Sony HT-ST9 Service Manual ▷ View online
HT-ST9
9
BOND FIXATION OF ELECTRIC PARTS
When the following parts are replaced, fi x the parts by using the bond (SC608Z2) (Refer to the fi gure below).
When the following parts are replaced, fi x the parts by using the bond (SC608Z2) (Refer to the fi gure below).
Target parts:
• AMP board: C7017, C7020, C7038, C7051, C7069, C7097, C7117, C7132, C7146, C7166
• POWER board: C902, C903, C905, C907, C914, C939, C967, C970, C988, C989, C990, C994, D901, R944, TH901, VDR901
• AMP board: C7017, C7020, C7038, C7051, C7069, C7097, C7117, C7132, C7146, C7166
• POWER board: C902, C903, C905, C907, C914, C939, C967, C970, C988, C989, C990, C994, D901, R944, TH901, VDR901
C914
(US, Canadian and Taiwan model only)
C903 or C990
C902 or C989
VDR901
C905
D901
TH901
C939
R944
C967
C970
C994
C7166
C7146
C7132
C7117
C7097
C7069 C7051 C7038
C7020
C7017
C907 or C988
– POWER Board (Component Side) –
– AMP Board (Side A) –
–
Side view
–
Ver. 1.1
HT-ST9
10
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-10. AMP BOARD
(Page
(Page
19)
2-11. IO BOARD
(Page
(Page
20)
2-13. POWER CORD (AC1)
(Page
(Page
22)
2-14. POWER BOARD
(Page
(Page
23)
to page 11
2-12. MB1406 BOARD
(Page
(Page
21)
2-2. COVER (REAR) BLOCK
(Page
(Page
12)
2-3. REAR PANEL (L) BLOCK
(Page
(Page
13)
2-4. REAR PANEL (R) ASSY,
BASE COVER (REAR)
(Page
14)
2-6. PANEL (SIDE L, R)
(Page
(Page
15)
2-7. PANEL (BOTTOM) BLOCK
(Page
(Page
16)
2-8. CHASSIS
BLOCK-1
(Page
17)
2-9. CHASSIS
BLOCK-2
(Page
18)
2-24. GRILLE ASSY
(Page
(Page
33)
2-5. KEY BOARD, BUTTON ASSY
(Page
(Page
14)
Note: When disassembling with the speaker side face down,
make sure to install the grille assy.
Disassembling with the speaker side face down without
installing the grille assy will damage the protrusion of
the
tweeter.
If the grille assy cannot be installed, make sure not to
disassemble with the speaker side face down.
grille assy
speaker side face
HT-ST9
11
from page 10
2-33. LOUDSPEAKER
(SP5, SP6, SP7, SP8) (CENTER)
(Page
41)
2-27. DISPLAY BOARD BLOCK-2
(Page
(Page
35)
2-29. LOUDSPEAKER (SP3, SP4) (R-ch)-1
(Page
(Page
37)
2-30. LOUDSPEAKER (SP3, SP4) (R-ch)-2
(Page
(Page
38)
2-31. LOUDSPEAKER (SP1, SP2) (L-ch)-1
(Page
(Page
39)
2-32. LOUDSPEAKER (SP1, SP2) (L-ch)-2
(Page
(Page
40)
2-25. NFC MODULE (NFC1)
(Page
(Page
33)
2-15. RF MODULATOR BLOCK-1
(Page
(Page
24)
2-16. RF MODULATOR BLOCK-2
(Page
(Page
25)
2-17. RF MODULATOR BLOCK-3
(Page
(Page
26)
2-22. FRONT SPEAKER (R) BLOCK
(Page
(Page
31)
2-23. FRONT SPEAKER (L) BLOCK
(Page
(Page
32)
2-21. CENTER SPEAKER BLOCK
(Page
(Page
30)
2-20. CARD WLAN/BT COMBO (WIFI1)
(Page
(Page
29)
2-18. USB BOARD
(Page
(Page
27)
2-19. WS BOARD,
RF MODULATOR (RF1)
(Page
28)
2-26. DISPLAY BOARD BLOCK-1
(Page
(Page
34)
2-28. DISPLAY BOARD,
OLED DISPLAY (OLED1)
(Page
36)
2-34. LOUDSPEAKER (SP9, SP10)
(CENTER)-1
(Page
(CENTER)-1
(Page
42)
2-35. LOUDSPEAKER (SP9, SP10)
(CENTER)-2
(Page
(CENTER)-2
(Page
43)
2-36. CONNECTION CABLE WITH
SPEAKER (SPC3, SPC4)
(Page
44)
HT-ST9
12
Note: Follow the disassembly procedure in the numerical order given.
2-2. COVER (REAR) BLOCK
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
How to install the connector
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
6
cover (rear) block
– Rear view –
Note 1: Lay a soft piece of cloth
under the unit to avoid
damaging the grille assy.
3
eight screws
(BVTP3
u 8)
1
two screws
(BVTP3
u 8)
2
two step screws
(BVTP3
u 8)
4
Lift up the cover (rear) block
in the direction of the arrow.
5
KEY board
connector
(CN1901)
(CN1901)
:ire settinJ
KEY board
Note 2: When installing screws (BVTP3 × 8), follow the installing procedure in the numerical order given.
1
6
7
8
9
0
2
3
4
5
Right side
Top side
Left side
Bottom side
Note 3: When installing the cover (rear) block,
push the KEY board cable into the unit.
Click on the first or last page to see other HT-ST9 service manuals if exist.