Sony HT-ST7 Service Manual ▷ View online
HT-ST7
21
2-22. CABLE WITH CONNECTOR (SPC1) (L-ch)
1
terminal (narrow side)
[black]
1
terminal (wide side)
[gray]
3 cable with connector
(SPC1)
cable with connector
(SPC1)
(SPC1)
2 Remove the cord bushing
of cable with connector in
the direction of an arrow.
narrow side
[black]
[black]
wide side
[gray]
[gray]
MOUNTED board
NG
OK
cabinet (L) assy
cord bush
No gap.
There is a gap.
cable with connector
(SPC1)
(SPC1)
cabinet (L) assy
cord bush
:LUHVHWWLQJ
:LUHVHWWLQJ
–)URQWERWWRPYLHZ–
Note: When installing the cable with connector (SPC1), make
the position of caulking of terminals is outside.
HT-ST7
22
2-23. FRONT SPEAKER (R) BLOCK
1 two canoe clips (small)
1 two canoe clips (small)
3 sheet (jack)
2 three adhesive sheets
4 screw
(PTPWH3
u 8)
guide line
sheet (jack)
guide line
mountain fold
valley fold
4 screw (PTPWH3 u 8)
6KHHWMDFNVHWWLQJ
6 front speaker (R) block
5 three screws
(BVP-tite
3
u 8)
guide pin
ditch
Note 2: When installing the front
speaker (R) block, align
the guide pin and ditch.
–5HDUERWWRPYLHZ–
Note 1: Please spread a sheet under
a unit not to injure front side.
guide pin
ditch
HT-ST7
23
2-24. DISPLAY BOARD
1
saranet cushion
flexible flat cable
Note: When installing the flexible flat cable,
ensure the colored line.
No slanting after insertion.
colored line
connector
5 flexible flat cable (15P) (FFC6)
(CN801)
2 screw (BVTP3 u 12)
2 screw
(BVTP3
u 12)
6 two claws
7 holder (LED) assy
3 collar (damper)
3 collar (damper)
8 bushing (damper)
8 bushing (damper)
8 bushing (damper)
8 bushing (damper)
3 collar (damper)
3 collar
(damper)
2 screw
(BVTP3
u 12)
2 screw
(BVTP3
u 12)
4 Remove the DISPLAY board block
in the direction of an arrow.
9 DISPLAY board
– Front bottom view –
2-25. LOUDSPEAKER (6.5 cm) (SP4) (R-ch)
2 Remove the loudspeaker
(6.5 cm) (SP4) in the
direction of an arrow.
4 loudspeaker (6.5 cm)
(SP4)
1 two screws
(3.5)
1 two screws
(3.5)
:LUHVHWWLQJ
loudspeaker (6.5 cm)
(SP4)
(SP4)
terminals position
(wide side) [blue]
(wide side) [blue]
terminals position
(narrow side) [black]
(narrow side) [black]
Note 1: When installing the loudspeaker (6.5 cm) (SP4),
make the position of terminals as shown
in the figure below.
–)URQWERWWRPYLHZ–
3
terminal (narrow side)
[black]
3
terminal (wide side)
[blue]
loudspeaker (6.5 cm) (SP4)
Note 2: When installing the speaker wire, make the
position of caulking of terminals is outside.
narrow side
[black]
[black]
wide side
[blue]
[blue]
HT-ST7
24
2-26. LOUDSPEAKER (2 cm) (SP2) (R-ch)
3 Remove the baffle (R)
block in the direction
of an arrow.
5
screw (3.5)
5
screw (3.5)
2 screw (3.5)
2 two screws
(3.5)
1 label (TW)
1 label (TW)
2 screw
(3.5)
2 screw
(3.5)
2 three screws
(3.5)
6 loudspeaker (2 cm)
(SP2)
loudspeaker (2 cm) (SP2)
– Front bottom view –
4
terminal (narrow side)
[black]
4
terminal (wide side)
[red]
loudspeaker (2 cm) (SP2)
Note 1: When installing the loudspeaker (2 cm) (SP2),
match the terminal position with the marking.
– Baffle (R) block inner view –
terminal
marking
Note 2: When installing the speaker wire, make the
position of caulking of terminals is outside.
narrow side
[black]
[black]
wide side
[red]
[red]
:ire VettinJ
MOUNTED board
speaker wire from MOUNTED board
:ire VettinJ
Click on the first or last page to see other HT-ST7 service manuals if exist.