DOWNLOAD Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Service Manual ↓ Size: 6.02 MB | Pages: 41 in PDF or view online for FREE

Model
HT-SL7 HT-SL7A STR-KSL7 STR-SL7 TA-KSL7
Pages
41
Size
6.02 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
ht-sl7-ht-sl7a-str-ksl7-str-sl7-ta-ksl7.pdf
Date

Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Service Manual ▷ View online

2
STR-KSL7/SL7/TA-KSL7
    After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
    The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY  CHECK-OUT
To Exposed Metal 
Parts on Set
0.15 
µ
F
1.5 k
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A.  Using an AC voltmeter to check AC leakage.
AM tuner section
Tuning range
With 10-kHz tuning scale:
530 – 1710 kHz
With 9-kHz tuning scale:
531 – 1710 kHz
With 10-kHz tuning scale:
530 – 1610 kHz
With 9-kHz tuning scale:
531 – 1602 kHz
530 – 1610 kHz
531 – 1602 kHz
Antenna
Loop antenna
Intermediate frequency
450 kHz
Usable sensitivity
50 dB/m (at 1,000 kHz or
999 kHz)
S/N
54 dB (at 50 mV/m)
Harmonic distortion
0.5% (50 mV/m, 400 Hz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 dB
4) You can change the AM tuning scale to 9 kHz 
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down the + button and press the
 button. All preset stations will be erased when
you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
General
Power requirements
120 V AC, 60 Hz
110 – 120 V AC,
50/60 Hz
220 – 230 V AC,
50/60 Hz
230 V AC, 50/60 Hz
Power consumption
98 W
Power consumption (during standby mode)
1.7 W
1.9 W
Dimensions (w/h/d)
430 
×
 83 
×
 289 mm
including projecting parts
and controls
Mass (Approx.)
3.1 kg
US, Canadian models
E model
Mexican model
Malaysia, Singapore
models
STR-SL7 : US, STR-KSL7, Canadian, Mexican models
STR-SL7 : US, STR-KSL7, Canadian, Mexican models
TA-KSL7 : AEP, UK, Chinese models
STR-KSL7 : E model
STR-KSL7 : Malaysia, Singapore models
STR-KSL7 : Malaysia, Singapore models
STR-SL7 : US model
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-U305S (1)
R6 (size-AA) batteries (2)
Design and specifications are subject to change
without notice.
EXCEPT TA-KSL7
3
STR-KSL7/SL7/TA-KSL7
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
MODEL IDENTIFICATION
— BACK PANEL —
PARTS No.
4-235-042-1s
4-235-042-2s
4-235-042-3s
4-235-042-4s
4-235-042-5s
4-235-042-7s
4-235-042-9s
MODEL
STR-SL7
:US model
STR-KSL7 :Canadian model
STR-KSL7 :Malaysia, Singapore model
STR-KSL7 :E model
STR-KSL7 :Mexican model
TA-KSL7
:AEP, UK model
TA-KSL7
:Chinese model
1. GENERAL
·········································································· 4
2. TEST MODE
······································································ 5
3. DIAGRAMS
········································································ 7
3-1. Block Diagrams ····························································· 8
– Main Section – ··························································· 8
– Display/Power Section – ············································ 9
3-2. Printed Wiring Board  – Digital Section – ·················· 10
3-3. Schematic Diagram  – Digital Section (1/2) – ············ 11
3-4. Schematic Diagram  – Digital Section (2/2) – ············ 12
3-5. Printed Wiring Board  – Main Section (1/2) – ············ 13
3-6. Printed Wiring Board  – Main Section (2/2) – ············ 14
3-7. Schematic Diagram  – Main Section (1/3) – ··············· 15
3-8. Schematic Diagram  – Main Section (2/3) – ··············· 16
3-9. Schematic Diagram  – Main Section (3/3) – ··············· 17
3-10. Printed Wiring Board  – Panel Section – ····················· 18
3-11. Schematic Diagram  – Panel Section – ······················· 19
3-12. Schematic Diagram  – Video Section – ······················· 20
3-13. Printed Wiring Board  – Video Section – ···················· 21
3-14. IC Block Diagrams ······················································ 22
3-15. IC Pin Function Descriptions ······································ 25
4. EXPLODED VIEWS
······················································ 29
4-1. Front Panel Section ····················································· 29
4-2. Chassis Section ···························································· 30
5. ELECTRICAL PARTS LIST
······································· 31
Parts No.
TABLE OF CONTENTS
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
4
STR-KSL7/SL7/TA-KSL7
SECTION 1
GENERAL
This section is extracted
from instruction manual.
AUX 6 (18)
Cursor buttons (U/u) qh (14,
22–24)
Display qk (21)
DVD 3 (18)
LEVEL qj (22)
MASTER VOLUME qa (17, 18)
MULTI CH IN 8 (18)
MULTI CHANNEL DECODING
indicator 5
MUTING qd (18)
PHONES jack ql (18)
SET UP q; (14, 24)
SOUND FIELD +/– qs (19, 23)
SURR 9 (23)
TEST TONE qf (17)
TUNER 7 (18)
TV 4 (18)
VIDEO 2 (18)
?/1 (power) 1 (13, 17, 18, 23)
+/– qg (14, 22–24)
Main unit
1
2
3 456 7
8
9
q;
qa
qs
ql
qk
qj
qf
qg
qh
qd
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses ( ) for details.
5
STR-KSL7/SL7/TA-KSL7
SECTION 2
TEST MODE
FACTORY SET MODE
* All preset contents are reset to the default setting.
* Procedure:
While depressing the  SET UP  and the  SOUND FIELD –  buttons
simultaneously, press the power  ?/1  button to turn on the main
power.  The message FACTORY appears and switch off the set.
While depressing the  SET UP and the  SOUND FIELD –  buttons
simultaneously, press the power  ?/1  button again. The message
FACTORY appears and the present contents are reset to the default
values.
AM CHANNEL STEP 9 kHz/10 kHz
SELECTION MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Set the FUNCTION to AM.  Turn off the main power.
While depressing the   i  cursor button, press the power  ?/1
button to turn on the main power.  Either the message 9 k STEP or
10 k STEP appears.  Select the desired step.
* For US/Canadian/E model only
MICRO/NORMAL SPEAKER SELECTION MODE
* Either the micro speaker mode or normal speaker mode can be
selected.
* Procedure
Press the  ?/1  button while pressing the  +  cursor button to turn
on the power. Either the message MICRO SP. or NORM. SP.
appears. Select the derired mode.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the  SOUND FIELD +  button, press the power
?/1
  button to turn on the main power.  The message
S. F. CLR appears and initialization is performed.
DEMONSTRATION MODE
* Demonstration is performed.
* Procedure :
While depressing the  SET UP  button, press the power  ?/1
button. The message appears and demonstration is performed.
* To finish DEMONSTRATION MODE, press the power ?/1
button while the introduction message appears in the display.
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested.  When this test is activated,
all segments turn on at the same time, then each segment turns on
one after another.
* Procedure:
While depressing the  SET UP  and the  SOUND FIELD +  buttons
simultaneously, press the power  ?/1  button to turn on the main
power.
1. All segments turn on.
DVD ,  TV ,  MULTI CH IN  and  SURR  LED turn on.
2. Press the  VIDEO  button, confirm display
AUX ,  TUNER  and  LEVEL  LED turn on.
3. Press the  VIDEO  button, confirm display
MULTI CHANNEL DECODING(blue),  VIDEO and SET UP
LED turn on.
4. Press the  VIDEO  button, All segments turn off.
5. Every pressing of the VIDEO button turns on each segment and
LED one after another in the same order.
(Not only the VIDEO button, but also the other buttons such as
DVD ,  TV ,  AUX ,  TUNER can be used.)
KEY CHECK MODE
* Button check
* Procedure:
While depressing the MUTING and the ENTER buttons
simultaneously, press the power  ?/1  button to turn on the main
power.
REST 17 appears.
Every pressing of any button other than  ?/1  counts down the
buttons.  The buttons which are already counted once are not
counted again.  When all buttons are pressed REST 00 appears.
SW
L
SL
C
R
S
SR
SLEEP
SP.OFF
( ( ( L F E ) ) )
DIGITAL
OPT COAX MULTI CH IN
PRO LOGIC DTS MPEGSTEREO MONO RDS
MEMORY
MUTING
INFO
NEWS
TA
EQ
D.RANGE
D D
dB
kHz
mft.
MHz
SW
L
R
S
SLEEP
 L F E 
COAX
PRO LOGIC
MPEGSTEREO
RDS
MUTING
INFO
TA
D.RANGE
D D
k    
m   
MHz
SL
C
SR
SP.OFF
( ( (       ) ) )
DIGITAL
OPT
MULTI CH IN
DTS
MONO
MEMORY
NEWS
EQ
dB
  Hz
   ft.
Page of 41
Display

Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Service Manual ▷ Download

  • DOWNLOAD Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Service Manual ↓ Size: 6.02 MB | Pages: 41 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 in PDF for free, which will help you to disassemble, recover, fix and repair Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Audio. Information contained in Sony HT-SL7 / HT-SL7A / STR-KSL7 / STR-SL7 / TA-KSL7 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.