Sony HT-SL5 / STR-KSL5 Service Manual ▷ View online
26
STR-KSL5
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87-92
93
94
95
96
97
98
99
100
Pin Name
MD2
NOT IN USE
NOT IN USE
SIRCS
FUSE DETECT
POWER KEY
JOG(B)
JOG(A)
VOL(B)
VOL(A)
DIN
CLK
FL_STB
FAN_ON
FAN_CLK
POWER RELAY
PROTECTOR
F_CTRL2
F_CTRL1
REAR RELAY
CENTER RELAY
FRONT RELAY
TUNED
STEREO
MUTE
DO
RSTX
SLATCH
X1A
X0A
VSS
XO
XI
VCC3
NOT IN USE
NC
NOT IN USE
XMODE
CKSEL1
CLK
CE
DI
DO
ERROR
XSTATE
I/O
I
I
I
I
I
I
I
I
I
I
O
O
O
I
I
O
I
O
O
O
O
O
I
I
O
I
I
O
—
—
—
O
I
—
I
I
I
O
O
O
O
O
I
I
I
Description
Flash programming MD2 input
Ground terminal
Ground terminal
Data input from the remote control receiver
Connected to +3.3V through the resistor (47k ohm)
Power swich detection signal input
Not used
Not used
Volume signal input from the rotary encoder
Volume signal input from the rotary encoder
Serial control data output to the FL/LED driver (IC152)
Clock signal output to the FL/LED driver (IC152)
STB signal output to the FL/LED driver (IC152)
Fan on detection signal input
Feedback signal input from the fan (FAN901)
Power relay drive signal output
Protect detection signal input
Fan speed control signal output
Fan ON/OFF control signal output
Surround relay drive signal output
Center relay drive signal output
Front relay drive signal output
Tuning a frequency detection signal input from the tuner
STEREO tuning signal from the tuner
Muting control signal output from the tuner
Data input from the tuner
System reset input
Serial control latch signal output to the tuner
Not used
Not used (connected to ground terminal)
Ground terminal
Terminal for a oscillator
Terminal for a oscillator
+3.3V (STBY)
Not used
Not used
Not used
Reset signal output to DIR (IC1101)
Not used
Clock signal output to DIR (IC1101)
Chip enable signal output to DIR (IC1101)
Write data output to DIR (IC1101)
Read data input from DIR (IC1101)
“PLL lock error, data error flag input from DIR (IC1101)”
Source clock selection monitor input from DIR (IC1101)
SECTION 4
EXPLODED VIEWS
NOTE:
•
•
-XX, -X mean standardized parts, so they may
have some differences from the original one.
have some differences from the original one.
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
in the exploded views are not supplied.
27
STR-KSL5
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
1
8
7
5
chassis section
8
6
#2
9
9
10
8
#1
#1
not
supplied
supplied
not
supplied
supplied
1
3
#1
2
4
1
4-977-358-01 CUSHION
2
4-241-511-01 KNOB (VOL)
3
X-4954-992-1 PANEL ASSY, FRONT
4
3-354-981-11 SPRING (SUS), RING
5
1-685-654-11 IR BOARD
6
1-773-045-11 WIRE (FLAT TYPE) (17 CORE)
4-1. Front Panel Section
7
A-4729-864-A DISPLAY BOARD, COMPLETE
8
4-951-620-01 SCREW (2.6X8), +BVTP
9
3-070-883-11 SCREW, TAPPING
10
4-241-509-01 CASE
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#2
7-685-133-19 SCREW +P 2.6X6 TYPE2 SLIT
28
STR-KSL5
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
#1
#1
#1
#1
#1
#1
#1
#1
#1
#3
#1
#1
55
56
58
57
62
59
52
65
61
51
52
53
54
63
T901
FAN901
TU901
F901
64
64
66
60
61
not
supplied
supplied
4-2. Chassis Section
51
A-4729-851-A AMPLIFIER BOARD, COMPLETE
52
3-531-576-11 RIVET
53
4-943-687-01 HOLDER, PC BOARD
54
1-685-650-11 STANDBY BOARD
* 55
3-703-244-00 BUSHING (2104), CORD
0 56
1-777-071-22 CORD, POWER
57
A-4729-847-A DIGITAL BOARD, COMPLETE
58
1-773-106-11 WIRE (FLAT TYPE) (19 CORE)
59
1-773-207-11 WIRE (FLAT TYPE) (25 CORE)
60
1-769-904-11 WIRE (FLAT TYPE) (9 CORE)
61
1-769-876-11 WIRE (FLAT TYPE) (7 CORE)
62
A-4729-852-A INPUT BOARD, COMPLETE
63
1-685-653-11 VIDEO BOARD
64
4-965-822-01 FOOT
65
4-214-557-21 CUSHION
66
1-765-325-11 WIRE (FLAT TYPE) (11 CORE)
0 F901
1-532-463-51 FUSE 1A/250V
FAN901 1-763-561-22 FAN, D.C.
0 T901
1-437-862-11 TRANSFORMER, POWER
TU901
1-693-580-21 TUNER
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#3
7-685-880-09 SCREW +BVTT 4X6 (S)
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
29
SECTION 5
ELECTRICAL PARTS LIST
NOTE:
•
•
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
•
-XX, -X mean standardized parts, so they
may have some difference from the original
one.
may have some difference from the original
one.
•
Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•
CAPACITORS:
uF:
uF:
µF
•
COILS
uH:
uH:
µH
•
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
STR-KSL5
When indicating parts by reference number,
please include the board name.
please include the board name.
•
SEMICONDUCTORS
In each case, u:
In each case, u:
µ, for example:
uA...:
µA... , uPA... , µPA... ,
uPB... ,
µPB... , uPC... , µPC... ,
uPD...,
µPD...
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
A-4729-851-A AMPLIFIER BOARD, COMPLETE
**************************
3-531-576-11 RIVET
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
7-685-872-09 SCREW +BVTT 3X8 (S)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
7-685-872-09 SCREW +BVTT 3X8 (S)
< CAPACITOR >
C501
1-126-963-11 ELECT
4.7uF
20.00% 50V
C502
1-162-282-31 CERAMIC
100PF
10%
50V
C503
1-162-282-31 CERAMIC
100PF
10%
50V
C504
1-162-195-31 CERAMIC
4.7PF
10.00% 50V
C506
1-126-960-11 ELECT
1uF
20.00% 50V
C507
1-113-342-11 CERAMIC
0.1uF
50V
C508
1-126-960-11 ELECT
1uF
20.00% 50V
C509
1-126-933-11 ELECT
100uF
20.00% 16V
C510
1-113-342-11 CERAMIC
0.1uF
50V
C511
1-136-157-00 FILM
0.022uF
5.00%
50V
C561
1-126-963-11 ELECT
4.7uF
20.00% 50V
C562
1-126-960-11 ELECT
1uF
20.00% 50V
C563
1-126-960-11 ELECT
1uF
20.00% 50V
C564
1-126-963-11 ELECT
4.7uF
20.00% 50V
C565
1-126-933-11 ELECT
100uF
20.00% 16V
C601
1-126-963-11 ELECT
4.7uF
20.00% 50V
C602
1-162-282-31 CERAMIC
100PF
10%
50V
C603
1-162-282-31 CERAMIC
100PF
10%
50V
C604
1-162-195-31 CERAMIC
4.7PF
10.00% 50V
C606
1-126-960-11 ELECT
1uF
20.00% 50V
C607
1-113-342-11 CERAMIC
0.1uF
50V
C608
1-126-960-11 ELECT
1uF
20.00% 50V
C609
1-126-933-11 ELECT
100uF
20.00% 16V
C610
1-113-342-11 CERAMIC
0.1uF
50V
C611
1-136-157-00 FILM
0.022uF
5.00%
50V
C641
1-130-483-00 MYLAR
0.01uF
5%
50V
C642
1-130-483-00 MYLAR
0.01uF
5%
50V
C643
1-130-483-00 MYLAR
0.01uF
5%
50V
C651
1-126-963-11 ELECT
4.7uF
20.00% 50V
C652
1-162-282-31 CERAMIC
100PF
10%
50V
C653
1-162-282-31 CERAMIC
100PF
10%
50V
C654
1-162-195-31 CERAMIC
4.7PF
10.00% 50V
C656
1-126-960-11 ELECT
1uF
20.00% 50V
C657
1-113-342-11 CERAMIC
0.1uF
50V
C658
1-126-960-11 ELECT
1uF
20.00% 50V
C659
1-126-933-11 ELECT
100uF
20.00% 16V
C660
1-113-342-11 CERAMIC
0.1uF
50V
C661
1-136-157-00 FILM
0.022uF
5.00%
50V
C701
1-126-963-11 ELECT
4.7uF
20.00% 50V
C702
1-162-282-31 CERAMIC
100PF
10%
50V
C703
1-162-282-31 CERAMIC
100PF
10%
50V
C704
1-162-195-31 CERAMIC
4.7PF
10.00% 50V
C706
1-126-960-11 ELECT
1uF
20.00% 50V
C707
1-113-342-11 CERAMIC
0.1uF
50V
C708
1-126-960-11 ELECT
1uF
20.00% 50V
C709
1-126-933-11 ELECT
100uF
20.00% 16V
C710
1-113-342-11 CERAMIC
0.1uF
50V
C711
1-136-157-00 FILM
0.022uF
5.00%
50V
C730
1-126-934-11 ELECT
220uF
20.00% 10V
C732
1-136-165-00 FILM
0.1uF
5.00%
50V
C741
1-130-483-00 MYLAR
0.01uF
5%
50V
C751
1-126-963-11 ELECT
4.7uF
20.00% 50V
C752
1-162-282-31 CERAMIC
100PF
10%
50V
C753
1-162-282-31 CERAMIC
100PF
10%
50V
C754
1-162-195-31 CERAMIC
4.7PF
10.00% 50V
C756
1-126-960-11 ELECT
1uF
20.00% 50V
C757
1-113-342-11 CERAMIC
0.1uF
50V
C758
1-126-960-11 ELECT
1uF
20.00% 50V
C759
1-126-933-11 ELECT
100uF
20.00% 16V
C760
1-113-342-11 CERAMIC
0.1uF
50V
C761
1-136-157-00 FILM
0.022uF
5.00%
50V
C791
1-130-483-00 MYLAR
0.01uF
5%
50V
C801
1-136-169-00 MYLAR
0.22uF
5.00%
50V
C802
1-136-169-00 MYLAR
0.22uF
5.00%
50V
C811
1-126-943-11 ELECT
2200uF
20.00% 25V
C812
1-126-942-61 ELECT
1000uF
20.00% 25V
C813
1-101-001-00 CERAMIC
0.001uF
50V
C814
1-101-001-00 CERAMIC
0.001uF
50V
C815
1-130-495-00 MYLAR
0.1uF
5%
50V
C816
1-130-495-00 MYLAR
0.1uF
5%
50V
C817
1-126-936-11 ELECT
3300uF
20.00% 16V
C818
1-126-955-11 ELECT
4700uF
20.00% 35V
C819
1-126-955-11 ELECT
4700uF
20.00% 35V
C820
1-126-948-11 ELECT
100uF
20.00% 35V
C821
1-126-967-11 ELECT
47uF
20.00% 50V
C871
1-126-933-11 ELECT
100uF
20.00% 16V
< CONNECTOR >
CN801
1-691-767-11 PLUG (MICRO CONNECTOR) 5P
* CN802
1-564-508-11 PLUG, CONNECTOR 5P
CN820
1-770-479-11 PLUG,CONNECTOR PIN(PC BOARD)4P
CN821
1-784-922-11 PIN, CONNECTOR 5P
CN822
1-784-780-11 CONNECTOR, FFC 19P
CN823
1-568-828-11 CONNECTOR, FFC 9P
CN861
1-779-978-11 PIN, CONNECTOR 3P
AMPLIFIER
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
Click on the first or last page to see other HT-SL5 / STR-KSL5 service manuals if exist.