Sony HT-SF2300 / HT-SS2300 / STR-KS2300 Service Manual ▷ View online
STR-KS2300
6
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2. CASE
(Page
(Page
6)
3-3. HDMI
BOARD
(Page
7)
3-5. MAIN
BOARD
(Page
8)
3-4. FRONT PANEL BLOCK
(Page
(Page
7)
SET
Note: Follow the disassembly procedure in the numerical order given.
3-2. CASE
two screws
(BVTP3
(BVTP3
× 8)
two tapping screws
Remove the case
in the direction of arrow ".
two tapping screws
"
STR-KS2300
7
3-3. HDMI BOARD
two screws
(BVTP3
(BVTP3
× 8)
three screws
(BVTP3
(BVTP3
× 8)
left HDMI bracket
HDMI board
connector
(CN3509)
(CN3509)
three screws
(BVTP3
(BVTP3
× 8)
wire (flat type) (17 core)
(HDMI BOARD (CN3511),
MAIN BOARD (CNS506))
3-4. FRONT PANEL BLOCK
screw
(BVTP3
(BVTP3
× 8)
wire (flat type) (19 core)
(CNS510)
(CNS510)
connector
(CNP500)
(CNP500)
saranet
cushion
three screws
(BVTP3
(BVTP3
× 8)
two claws
claw
three claws
front panel block
claw
STR-KS2300
8
3-5. MAIN BOARD
seven screws
(BVTP3
(BVTP3
× 8)
R four screws
(PWH3
(PWH3
× 8)
wire (flat type) (11 core)
(CNS508: AEP, UK)/(9 core)
(CNS509: except AEP, UK)
wire (flat type) (5 core)
(CNS505)
(CNS505)
wire (flat type) (19 core)
(CNS510)
(CNS510)
connector
(CNP500)
(CNP500)
three connectors
(CN902, CN905, CN906)
screw (BVTP3 × 14)
screw (BVTP3 × 10)
screw (BVTP3 × 10)
heat sink (AMP)
RB MAIN board
two radiation
sheets (AMP)
STR-KS2300
STR-KS2300
9
9
SECTION 4
TEST MODE
S.F. CLEAR MODE
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [SOUND FIELD +] button, press the [
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [SOUND FIELD +] button, press the [
?/1
]
button to turn on the main power.
2. The message “S.F. CLR.” appears and initialization is per-
formed.
CHANGE-OVER THE AM TUNING INTERVAL
(EXCEPT AEP, UK MODELS)
The AM tuning interval can be changed over 9 kHz or 10kHz.
Procedure:
1. While pressing the [PRESET TUNING +] button, press the
(EXCEPT AEP, UK MODELS)
The AM tuning interval can be changed over 9 kHz or 10kHz.
Procedure:
1. While pressing the [PRESET TUNING +] button, press the
[
?/1
] button to turn on the main power.
2. The AM turning interval changed over 9 kHz or 10 kHz.
FACTORY PRESET MODE
All preset contents are reset to the default setting.
Procedure:
1. While pressing the [SOUND FIELD +] and [PRESET TUNING
FACTORY PRESET MODE
All preset contents are reset to the default setting.
Procedure:
1. While pressing the [SOUND FIELD +] and [PRESET TUNING
–] buttons, press the [
?/1
] button to turn on the main power.
2. The message “FACTORY” appears and the present contents
are reset to the default values.
VERSION MODE
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [INPUT SELECTOR +] and [PRESET TUN-
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [INPUT SELECTOR +] and [PRESET TUN-
ING +] buttons, press the [
?/1
] button to turn on the main power.
2. The model, the distination and the software version number
appear.
FL CHECK MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [PRESET TUNING +] and [SOUND
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [PRESET TUNING +] and [SOUND
FIELD –] buttons, press the [
?/1
] button to turn on the main
power.
2. All
segments
turn on.
3. Press the [INPUT SELECTOR +] or [INPUT SELECTOR –]
button.
4. Half of segments turn on.
5. Press the [INPUT SELECTOR +] or [INPUT SELECTOR –]
5. Press the [INPUT SELECTOR +] or [INPUT SELECTOR –]
button once again.
6. Others half of segments turn on.
7. Press the [INPUT SELECTOR +] or [INPUT SELECTOR –]
7. Press the [INPUT SELECTOR +] or [INPUT SELECTOR –]
button once again.
8. All segments turn off.
KEY CHECK MODE
This mode is used to check the key.
Procedure:
1. While pressing the [MUTING] and [PRESET TUNING –]
This mode is used to check the key.
Procedure:
1. While pressing the [MUTING] and [PRESET TUNING –]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “REST 06” appears.
3. Every pressing of any button other than the [
3. Every pressing of any button other than the [
?/1
] button counts
down the buttons. The buttons which are already counted once
are not counted again.
are not counted again.
4. When all buttons are pressed, the message “REST 00” ap-
pears.
5. Either [INPUT SELECTOR+] or [INPUT SELECTOR–] but-
ton can be checked each time the key check mode is activat-
ed.
ed.
SWAP AUTO MODE
(Not used for the servicing)
(Not used for the servicing)
SHIPMENT MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [PRESET TUNING –] and [SOUND FIELD
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [PRESET TUNING –] and [SOUND FIELD
–] buttons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears, then the message
“CLEARED” appears.
PROTECTOR EVER MODE
When this mode is used, a protector on state is maintainable.
Procedure:
1. While pressing the [SOUND FIELD +] and [INPUT SELECTOR
When this mode is used, a protector on state is maintainable.
Procedure:
1. While pressing the [SOUND FIELD +] and [INPUT SELECTOR
+] buttons, press the [
?/1
] button to turn on the main power.
2. The message “PROTEVER” appears.
VACS OFF MODE
This mode is used to switch off the VACS (Variable Attenuation
Control System).
Procedure:
1. Press the buttons of standard commander (RM-AAV022) (PART
This mode is used to switch off the VACS (Variable Attenuation
Control System).
Procedure:
1. Press the buttons of standard commander (RM-AAV022) (PART
No.: 1-480-586-11) (US, Canadian models) or (RM-AAU023)
(PART No.: 1-480-587-11) (Except US, Canadian models) in
order of [DISPLAY]
(PART No.: 1-480-587-11) (Except US, Canadian models) in
order of [DISPLAY]
→ [DISPLAY] → [DISPLAY] → [MAS-
TER VOL +]
→ [3].
2. The message “VACS OFF” appears and the switch off the
VACS.
DCAC TEST MODE
(Not used for the servicing)
RE-BOX CLASSIFICATION TEST MODE
Procedure:
1. While pressing the [INPUT SELECTOR –] and [SOUND
Procedure:
1. While pressing the [INPUT SELECTOR –] and [SOUND
FIELD –] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “R.BOX
[][][]XX” appears.
XX: times set powered on
HDMI CONTROL ON/OFF MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Press the buttons of standard commander (RM-AAV022)
(PART No.: 1-480-586-11) (US, Canadian models) or (RM-
AAU023) (PART No.: 1-480-587-11) (Except US, Canadian
models) in order of [AMP MENU] → [↓] → [↓] → [↓] → [↓]
→ [↓] → [→] → [↓] → [→] → [↓].
AAU023) (PART No.: 1-480-587-11) (Except US, Canadian
models) in order of [AMP MENU] → [↓] → [↓] → [↓] → [↓]
→ [↓] → [→] → [↓] → [→] → [↓].
3. The message “CTRL ON” appears.
4. Press the buttons [↑] of standard commander.
5. The message “CTRL OFF” appears.
4. Press the buttons [↑] of standard commander.
5. The message “CTRL OFF” appears.
SECTION 5
ELECTRICAL CHECK
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 1 kHz
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
Click on the first or last page to see other HT-SF2300 / HT-SS2300 / STR-KS2300 service manuals if exist.