Sony HT-K5 / SA-WP9000 / SS-BSP5K / SS-CNP5K / SS-SRP5K Service Manual ▷ View online
SERVICE MANUAL
Front speakers (SS-BSP5K)
Center speaker (SS-CNP5K)
Surround speakers (SS-SRP5K)
Center speaker (SS-CNP5K)
Surround speakers (SS-SRP5K)
Front speakers
2 way, magnetically
shielded
shielded
Center speaker Full
range,
magnetically
shielded
Surround speakers
Full range
Speaker units
Front speakers
Front speakers
200 mm cone type, 25 mm
Horn Tweeter
Horn Tweeter
Center/surround speakers 80 mm cone type
Enclosure type
Enclosure type
Bass reflex
Rated Impedance
6 ohms
Dimension (w/h/d) (Approx.)
Front speakers
Front speakers
270
× 468 × 266 mm
Center speaker
270
× 127 × 130 mm
Surround speakers
126
× 185 × 130 mm
RMS output
165 W (6 ohms, 100 Hz,
THD 10%)
THD 10%)
Music power 200
W
Input LINE
IN
(input
pin jacks)
Dimensions (w/h/d) (Approx.)
335
× 410 × 360 mm
including front panel
M
Design and specifications are subject to change
without notice.
without notice.
ass (Approx.)
11.0 kg
Mass (Approx.)
Front speakers
Front speakers
7.0 kg
Center speaker
1.7 kg
Surround speaker
1.0 kg
Power requirements
Power consumption
Area code
Power requirements
SP, MY
230 – 240 V AC,
50/60 Hz
50/60 Hz
E51
120/220/240 V AC,
50/60 Hz
50/60 Hz
Area code
Power consumption
SP, MY, E51
80 W
Sub woofer (SA-WP9000)
Speaker system
Active sub woofer,
magnetically shielded
magnetically shielded
Speaker unit
250 mm cone type
Enclosure type
Acoustically loaded bass
reflex
reflex
E Model
Ver. 1.0 2006.03
SPECIFICATIONS
9-887-118-01
2006C05-1
© 2006.03
© 2006.03
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
•
SA-WP9000 is the active sub woofer in HT-K5.
•
SS-BSP5K is the front speakers in HT-K5.
•
SS-CNP5K is the center speaker in HT-K5.
•
SS-SRP5K is the surround speaker in HT-K5.
This receiver incorporates Dolby* Digital and Pro Logic Surround and the
DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of
Dolby Laboratories.
Dolby Laboratories.
**“DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
SA-WP9000/SS-BSP5K/
CNP5K/SRP5K
ACTIVE SUB WOOFER/FRONT SPEAKERS/
CENTER SPEAKER/SURROUND SPEAKERS
Photo: SS-BSP5K
Photo: SS-CNP5K Photo: SS-SRP5K
Photo: SA-WP9000
•
JIG
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
• Abbreviation
E51 : Chilean and Peruvian models
MY : Malaysia model
SP
MY : Malaysia model
SP
: Singapore model
2
SA-WP9000/SS-BSP5K/CNP5K/SRP5K
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SA-WP9000/SS-BSP5K/CNP5K/SRP5K
3
Note:
Follow the disassembly procedure in the numerical order given.
1-1. LOUDSPEAKER (SA-WP9000)
SECTION 1
DISASSEMBLY
5
connector
6
front panel assy
8
two harnesses
4
ten bosses
9
loudspeaker (25cm)
(SP6)
(SP6)
7
four screws
(+BVTP4
(+BVTP4
×
20) (TYPE1)
3
Raise the front panel assy a little by little
from bottom to top of the set.
from bottom to top of the set.
1
Insert a flat-tip screwdriver into a slit
in the bottom of the set
to raise the front panel assy a little.
in the bottom of the set
to raise the front panel assy a little.
2
Insert the jig (J-2051-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
made by inserting the screwdriver,
and raise the front panel assy gradually.
2
Insert the jig (J-2051-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
made by inserting the screwdriver,
and raise the front panel assy gradually.
Note 2: Remove the front panel assy by paying attention particulaly
to the periphyery of ten bosses
where the front panel assy bonded tightly.
where the front panel assy bonded tightly.
Note 3: Take care not to damage the set
by applying an excessive force.
Note 1: front panel assy must be opend/raised
from right hand side towards left hand side
to avoid damage of LED wire and connector.
to avoid damage of LED wire and connector.
SA-WP9000/SS-BSP5K/CNP5K/SRP5K
4
1-2. MAIN BOARD (SA-WP9000)
qs
four screws
(BVTP3
(BVTP3
×
8)
qa
two screws
(BVTP4
(BVTP4
×
8)
1
seven screws
(BVTP4
(BVTP4
×
20)
2
screw
(BVTT4
(BVTT4
×
12 (S))
3
8
four screws
(BVTP4
(BVTP4
×
8)
9
POWER TRANS board
qd
MAIN board
6
rear cover
4
connector
(CN201)
(CN201)
5
connector
(CN3)
(CN3)
7
connector
(CN402)
(CN402)
0
two connectors
(CN301, CN601)
(CN301, CN601)