DOWNLOAD Sony HT-DDW7500 / HT-DDW8500 / STR-KM7500 Service Manual ↓ Size: 6.95 MB | Pages: 80 in PDF or view online for FREE

After press the [TUNING MODE] button, DCAC Factory test 
mode will start, below display will show:
 

“DCAC   x” 

x = 1, 2, 3, 4

  

If there is error happen, below display will show:

 

“ERR SD0x”  x = 1 

→ D1501 or R1530 problem

 

 

x = 2 

→ D1502 problem 

 

 

x = 3 

→ D1503 problem 

 

 

x = 4 

→ D1504 problem 

Connect front left speaker of the receiver and AUTO CAL micro-
phone. Turn [MASTER VOLUME] jog, there will be test tone 
sound output from front left speaker, and the display will change 
accordingly.

 

“AD - xxx” 

xxx = 0 to 255 (depends on loudness of test tone)

Note
When the value reaches more than 222, the test tone will muted 
(for production line checking). Thus, the AD value will drop to 0. 
To check the AD value again, power off the receiver and re-enter 
the test mode.

VACS  CONTROL  TEST  MODE
The VACS feature of the amplifi er is turned off purposely.
Procedure:
1.  While pressing the [MUSIC] and [A.F.D] buttons, press the 

[

?/1

] button to turn on the main power.

2.  The message “VACS OFF” appears.

HISTORY MODE
* The state that the set is used is memorized.
* Procedure:
1. While depressing the [GAME]  and the [A.F.D.] buttons simul-

taneously, press the [

?/1

] button to turn on the main power.

2. “HISTORY” appears.
3. Each time the [↑] / [↓] buttons on the remote commander is 

pressed, the item is switched in order as follows.

Items
Protector Count

COUNT XX

Total single power on time

SXXXHXXM

Sound Field

SND FLD 

Input function

FUNCTION

Input Mode

INP MODE

Digital Select

DIGI IN 

Stream information

STREAM 

Signal confi guration

CO XXXXX

Headphones

HP XXX

Volume

VOL XXX

Bass Setting

BASS XXX

Treble Setting

TREB XXX

Front Level Setting

F XXX 

Center Level Setting

CT XXX

Surround Left Level Setting

SL XXX

Surround Right Level Setting

SR XXX

Surround Back Left Level Setting

BL XXX

Surround Back Right Level Setting

BR XXX

Subwoofer Level Setting

SW XXX 

Total power on time

TXXXHXXM

Muting Status

MUTE XXX

Power on counter (Rebox test mode)

P.W. XXX

Protector Type

PRT XXXX

Temperature when protect

TEM XXXC

* Procedure:

1. While depressing the [NIGHT MODE] and the [MUSIC] 

buttons simultaneously, press the power [

?/1

] button to 

turn on the main power.

2. “PROTEVER” appears.

Procedure:
1.  Turn on the set.
2.  Input the following signal from signal generator to FM an-

tenna input directly.

Carrier frequency: A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation  : 75 kHz
Modulation  : 1 kHz
ANT input  : 1 kHz

Note:  Use 75 ohm coaxial cable to connect signal generator and the set. 

You cannot use video cable for checking.

 

Use signal generator whose output impedance is 75 ohm.

3.  Set to FM tuner function and scan the input FM signal with 

automatic scanning.

4. Confi rm that input frequency of A, B and C are detected and 

automatic scanning stops.

When the station signal is received in good condition, automatic 
scanning stops.

STR-KM7500

‡6LJQDOSDWK

IC102

AD_1

AD_2

P:_6:

DCAC_IN

DCAC

1

VOG_JOG_%

VOG_JOG_A

)/_5E6E7NC

FL_CLK

FL_DIN

FL_C6

NIG+70ODELED

08L7I_67LED

6I5C6

+3.3V67AND%<

+3.3V

+5V

CN6104

CNP102

FL101

VAC880FL8O5E6CEN7

DI6PLA<

7101

INP87_JOG_%

INP87_JOG_A

6107

086IC

6108

GA0E

610

08L7I67E5EO

6101

NIG+70ODE

6102

AFD

6103

0OVIE

6110

RV102

0A67ERVOL80E

RV101

INP876ELEC7OR

,40,41,42

1a

31,5

a

64

4a

27,3

a

51

28,2

,30,31,32,33,34,35,36,

37,38

2

53

1

2

3

4

7

8

Q101

Q111

D106

FLDI6PLA<DRIVER

Q110

D105

+5V

+3.3V

IC181

A0P

IC180

0ICA0P

CN173

LC+V2

RC+V2

5

7

VIDEO

0IC0ONO

10

RCH

RCH

D180

D181

J181

VIDEO2IN

A8DIO

VIDEO

R

L

V

A87OCAL0IC

J180

0IC

?/1

RCH

RCH

VIDEO
A8DIO

‡

RFKLVRPLWWHGGXHWRVDPHDVLFK.