Sony HT-DDW5500 / HT-DDW7500 / HT-DDW7600 / HT-DDW8500 / HT-DDW8600 / TA-KMSW500 Service Manual ▷ View online
TA-KMSW500
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1. GENERAL
............................................................................ 3
2. DISASSEMBLY
2-1.
Case ..................................................................................... 4
2-2. Back Panel Section ............................................................. 5
2-3. Front Panel Section ............................................................. 5
2-4. Main Board Section ............................................................ 6
2-3. Front Panel Section ............................................................. 5
2-4. Main Board Section ............................................................ 6
3. DIAGRAMS
3-1. Block Diagram ................................................................... 7
3-2. Printed Wiring Boards – MAIN Board – ........................... 9
3-3. Schematic Diagram – MAIN Board – .............................. 10
3-4. Printed Wiring Boards – LED RIGHT,
3-2. Printed Wiring Boards – MAIN Board – ........................... 9
3-3. Schematic Diagram – MAIN Board – .............................. 10
3-4. Printed Wiring Boards – LED RIGHT,
LED LEFT, VOL CONTROL Section – ............................11
3-5. Schematic Diagram – LED RIGHT,
LED LEFT, VOL CONTROL Section – ........................... 12
4. EXPLODED VIEWS
4-1.
Case ................................................................................... 14
4-2. Front Panel Section ........................................................... 15
4-3. Back Panel Section ........................................................... 16
4-4. Chassis Section ................................................................. 17
4-3. Back Panel Section ........................................................... 16
4-4. Chassis Section ................................................................. 17
5. ELECTRICAL PARTS LIST
......................................... 18
TA-KMSW500
3
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
LOCATION OF CONTROLS
Front Panel
RT
RB
ILLUMINATION
VOLUME
ON
OFF
MIN
RE
- ILLUMINATION
The illumination is on
(initial setting).
(initial setting).
The illumination is off.
. Illumination
indicator
Lights up to indicate the
subwoofer output level.
subwoofer output level.
ON
OFF
, SUBWOOFER
VOLUME
Turn to adjust the volume
level of the subwoofers.
level of the subwoofers.
Rear Panel
AUDIO
IN
SUBWOOFER ONLY FOR SS-WP7500
SUBWOOFER
IN
SYSTEM
CONTROL
SUBWOOFER
SPEAKERS
ONLY FOR
STR-KM5500/7500/8500
% SYSTEM CONTROL INPUT/OUTPUT
section
SYSTEM
CONTROL
OUT jack
CONTROL
OUT jack
Connects to the
power amplifier
(page 18).
power amplifier
(page 18).
SYSTEM
CONTROL IN
jack
CONTROL IN
jack
Connects to the
receiver (page 18).
receiver (page 18).
OUT
DC5V
50mA MAX
50mA MAX
SYSTEM CONTROL
IN
SYSTEM
CONTROL
& SPEAKERS section
Connects to the
supplied speakers
(page 16).
supplied speakers
(page 16).
' AUDIO INPUT/OUTPUT section
AUDIO IN
jack
jack
Connects to the
receiver.
receiver.
Black
TA-KMSW500
4
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
2-1. CASE
(Page 4)
2-2. BACK PANEL SECTION
(Page 5)
2-3. FRONT PANEL SECTION
(Page 5)
2-4. MAIN BOARD SECTION
(Page 6)
SET
Note: Follow the disassembly procedure in the numerical order given.
2-1. CASE
two screws
(+BVST 4
× 8) (black)
two screws
(+BVST 4
× 8) (black)
three screws
(+BVTP 3
× 8)
case
TA-KMSW500
5
2-2. BACK PANEL SECTION
2-3. FRONT PANEL SECTION
five screws
(+BVTP 3 x 8)
CNP651 (7P)
front panel section
CNP901 (2P)
CNP650 (3P)
five screws
(+BVTP 3
× 8)
two screws
(+BVTP 3
× 8)
one screw
(+BVTP 3
× 8)
back panel section