Sony HT-CT380 / HT-CT381 / SA-CT380 / SA-CT381 Service Manual ▷ View online
HT-CT380/CT381
10
2-4. NFC MODULE (NFC1)
3 Peel off the
release
paper.
4 Install the NFC
module (NFC1) to
the cabinet top.
2 flexible flat cable
(6 core) (FFC4)
5 Slant to insert the
sheet (NFC) into
the
slot.
slot
1 Paste the double
adhesive tape (NFC).
NFC module
(NFC1)
(NFC1)
6 Insert the sheet
(NFC) in the
other
slot.
sheet (NFC)
NFC module
(NFC1)
(NFC1)
filament tape
(sub material)
(sub material)
flexible flat cable
(6 core) (FFC4)
(6 core) (FFC4)
Terminal face is
below side.
below side.
sheet (NFC)
slot
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable,
ensure that the colored line is parallel
to the connector after insertion.
When installing the flexible flat cable,
ensure that the colored line is parallel
to the connector after insertion.
How to install the NFC module (NFC1)
Note: Please spread a sheet under a
unit not to injure cabinet top.
4 sheet (NFC)
2 Peel off the double
adhesive tape (NFC).
5 NFC module
(NFC1)
3 flexible flat cable
(6 core) (FFC4)
1 filament tape
(sub
material)
– Cabinet top bottom view –
– NFC module bottom view –
rear side
cabinet top block
left side
right side
front side
Flexible flat cable (FFC) settinJ
HT-CT380/CT381
11
2-5. DISPLAY BOARD
6 flexible flat cable
(6 core) (FFC4) (CN804)
4 flexible flat cable
(18 core) (FFC3) (CN803)
1 two screws
(BVTP3
u 8)
1 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
7 packing (CZ2)
0 DISPLAY board
9 cover (FL-CZ2) assy
5 non woven fabric
(T0.3)
2 Remove the DISPLAY board block
in the direction of the arrow.
3 filament tape
(sub
material)
Note: Please spread a sheet under a
unit not to injure cabinet top.
– Cabinet top bottom view –
rear side
cabinet top block
left side
right side
front side
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
)lexible flat cable ))C settinJ
3acNinJ C= settinJ
DISPLAY board
DISPLAY board
non woven fabric
(T0.3)
(T0.3)
flexible flat cable
(FFC4)
(FFC4)
flexible flat cable
(6 core) (FFC4)
(6 core) (FFC4)
flexible flat cable
(18 core) (FFC3)
(18 core) (FFC3)
flexible flat cable
(FFC3)
(FFC3)
filament tape
(sub material)
(sub material)
Terminal face is
below side.
below side.
Terminal face is
below side.
below side.
guide line
fold
packing (CZ2)
DISPLAY board
HT-CT380/CT381
12
2-6. POWER BOARD
3RZHUFRUGVHWWLQJ
wiring stopper
Dress the wiring stopper
toward the arrow direction.
toward the arrow direction.
CN901
6 POWER board
5 two screws
(BV3
u 7)
5 two screws
(BV3
u 7)
1 Remove the wire
from the wiring stopper
with cushion (CZ2-A).
with cushion (CZ2-A).
3 Remove the power cord
from the wiring stopper.
4 power cord connector
(CN901)
cabinet (bottom) block
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
:LUHVHWWLQJ
Note 2: Do not fix the wire near the heat sink.
MAIN board
CN1005
wiring stopper
cushion (CZ2-A)
CN3002
CN3005
heat sink
heat sink
2 connector (CN1005)
Note
1: Before connect this connector, refer to “CAPACITOR
ELECTRICAL DISCHARGE PROCESSING” on page 4.
&XVKLRQ&=$VHWWLQJ
Note 3: Paste the cushion (CZ2-A) to
screw head and wiring stopper.
wiring stopper
screw head
cushion
(CZ2-A)
(CZ2-A)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
connector
Insert at a slant.
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHSRZHUFRUGFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
HT-CT380/CT381
13
2-7. CONNECTION CABLE WITH SPEAKER (L-CH, R-CH) (SPC1, SPC2)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
How to install the connector
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
2 connector
(CN3002)
2 connector
(CN3001)
3 connection cable with speaker
(R-ch)
(SPC2)
3 connection cable
with
speaker
(L-ch)
(SPC1)
1 cushion (CZ2-A)
&RQQHFWLRQFDEOHZLWKVSHDNHU5FK63&VHWWLQJ
Push
Push
Push
CN3001
Vent hole
Note: Do not block the vent hole in the connection cable with
speaker (R-ch) (SPC2).
&RQQHFWLRQFDEOHZLWKVSHDNHU/FK63&VHWWLQJ
Push
Push
Push
Push
CN3002
cushion (CZ2-A)
Push
cabinet (bottom) block
Click on the first or last page to see other HT-CT380 / HT-CT381 / SA-CT380 / SA-CT381 service manuals if exist.