Sony HMZ-T2 (serv.man2) Service Manual ▷ View online
HMZ-T2
2-3
2-2. Head Mounted Unit (HMZ-T2H)
2-2-1. DISASSEMBLY FLOW
・This set can be disassembled in the order shown below.
2-2-2. ROOF BLOCK
(Page 2-4)
2-2-3. TOP COVER
(Page 2-4)
2-2-8. INDICATOR BLOCK
(Page 2-9)
2-2-7. ARM (FOREHEAD-T2) BLOCK
(Page 2-8)
2-2-4. BOTTOM COVER BLOCK
(Page 2-5)
2-2-5. DISPLAY UNIT
(Page 2-6)
2-2-6. HEAD BAND BLOCK
(Page 2-7)
UNIT (HMZ-T2H)
HMZ-T2
2-4
2-2-2. ROOF BLOCK
2-2-3. TOP COVER
2
claw
2
claw
2
claw
3
roof block
1 screw
(P M1.7
× 4)
1 screw
(P M1.7
× 4)
Note 1: When installing the top cover,
check that there is no crevice.
2 three screws
(P2
(P2
× 4)
3 three claws
3 three claws
5 top cover
3 three claws
4 rib
4 rib
4 two ribs
2 two screws
(P2
(P2
× 4)
1 two screws
(P1.4
(P1.4
× 3.5)
1 two screws
(P1.4
(P1.4
× 3.5)
NG
OK
Note 2: When installing the top
cover, check that the HP
hook sheets are not bit.
HP hook sheet is not biting.
(The whole is black)
(The whole is black)
HP hook sheet is biting.
(The about 1/3 upper part
looks white)
(The about 1/3 upper part
looks white)
HMZ-T2
2-5
2-2-4. BOTTOM COVER BLOCK
・
Wire setting
• Wire setting
• Note when installing bottom cover block
④ screw
(P1.4
× 3.5)
④ screw
(P1.4
× 3.5)
⑤ two screws (P M1.7 × 4)
⑤ screw
(P M1.7 × 4)
⑤ screw
(P M1.7 × 4)
⑤ screw
(P M1.7 × 4)
⑦ lug wire
④ three screws
(P1.4
× 3.5)
④ three screws
(P1.4
× 3.5)
⑨ claw
⑨ claw
⑧ three ribs
⑧ three ribs
⑩ bottom cover block
OP unit slide button
① connector
(CN1001)
③ switch unit flexible board
(CN901)
Note 1: Turn a caulking portion up.
Note 4: Bend and attach a peculiarity.
Note 5: Wire must not come outside.
Note 6: Before installing the bottom cover
block, slide the lenses and the
buttons to each outside.
Note 7: After installing a bottom cover block,
check the buttons can slide to right
and left.
Note 2: Caulking portion must not
overflow from the width of
metal plate of switch unit.
⑥ screw
(P 2 × 4)
② connector
(CN904)
indicator block
bottom cover
display unit
Note 3: Wire must not come outside.
HMZ-T2
2-6
2-2-5. DISPLAY UNIT
7 Remove the display unit
in the direction of an arrow.
8 display unit
3 HM cable connector
(CN101)
(CN101)
2
connector
(CN903)
5
rib
6
boss
6
boss
1 cabinet upper cushion
10
10
× 7 × 0.3
cabinet upper cushion 10
× 7 × 0.3
Note 2: There must not be inclination,
a float, and peeling.
Note 3: Do not plug up the hole of the
display unit.
Note 4: Wire must not slacken.
hole
Two concave portions be seen.
guide line
• Wire setting
• Display unit flexible board setting
Note 1: Fix the arm (forehead-T2) block at
back until a wire setting finishes.
4 two screws
(P2
(P2
× 4)
4 two screws
(P2
(P2
× 4)
4 screw
(P2
(P2
× 4)
4 three screws
(P2
(P2
× 4)
display unit flexible board
Click on the first or last page to see other HMZ-T2 (serv.man2) service manuals if exist.