Sony HMD-M11 Service Manual ▷ View online
– 29 –
NOTE FOR INSTALLATION
•
SLIDER COMPLETE ASS’Y
Install the part A of lever (head up)
to pass over the slider complete ass’y.
to pass over the slider complete ass’y.
part A
OK
NG
Take care not to damage
the detective switch.
the detective switch.
slider ass’y
– 30 –
SECTION 4
TEST MODE
4-1.
PRECAUTIONS FOR USE OF TEST MODE
1. As loading related operations will be performed regardless of
the test mode operations being performed, be sure to check
that the disc is stopped before setting and removing it. Even if
the
that the disc is stopped before setting and removing it. Even if
the
6 button is pressed while the disc is rotating during con-
tinuous playback, continuous recording, etc., the disc will not
stop rotating. Therefore, it will be ejected while rotating. Be
sure to press the
stop rotating. Therefore, it will be ejected while rotating. Be
sure to press the
6 button after pressing the NO button and
the rotation of disc is stopped.
2. The erasing-protection tab is not detected in the test mode.
Therefore, operating in the recording laser emission mode and
pressing the
pressing the
r REC button, the recorded contents will be
erased regardless of the position of the tab. When using a disc
that is not to be erased in the test mode, be careful not to enter
the continuous recording mode and traverse adjustment mode.
that is not to be erased in the test mode, be careful not to enter
the continuous recording mode and traverse adjustment mode.
4-1-1.
Recording Laser Emission Mode and Operating
Button
1. Continuous recording mode (CREC MODE)
2. Traverse adjustment mode (EFBAL ADJUST)
3. Laser power adjustment mode (LDPWR ADJUST)
4. Laser power check mode (LDPWR CHECK)
5. When pressing the
2. Traverse adjustment mode (EFBAL ADJUST)
3. Laser power adjustment mode (LDPWR ADJUST)
4. Laser power check mode (LDPWR CHECK)
5. When pressing the
r REC button.
4-2.
SETTING THE TEST MODE
With the power supply to the set in OFF (standby) status, press the
p button and NO button simultaneously, and the test mode is
activated.
4-3.
RELEASING THE TEST MODE
Press the FUNCTION button, and the power is turned OFF
(standby status) and the set becomes ready for normal operation.
(standby status) and the set becomes ready for normal operation.
4-4.
BASIC OPERATIONS OF THE TEST MODE
All operations are performed using the
= 0 button,
) + button, YES button, and NO button. The functions
of these buttons are as follows.
Table 4-1.
4-5.
SELECTING THE TEST MODE
Thirteen test modes are selected by pressing the
= 0 but-
ton, and
) + button.
Table 4-2.
•
For detailed description of each adjustment mode, refer to the
“5. ELECTRICAL ADJUSTMENTS”.
“5. ELECTRICAL ADJUSTMENTS”.
•
If a different adjustment mode has been selected by mistake,
press the NO button to exit from it.
press the NO button to exit from it.
*1: The EEP MODE, Scurve CHECK, MANUAL CMD and
SVDATA READ are not used in servicing. If set accidentally,
press the NO button immediately to exit it.
press the NO button immediately to exit it.
Button
Function
=0 button
)+ button
)+ button
YES button
Proceeds onto the next step.
Finalizes input.
Finalizes input.
NO button
Returns to previous step.
Stops operations
Stops operations
Changes parameters and modes.
Display
Contents
TEMP ADJUST
Temperature compensation offset
adjustment
adjustment
LDPWR ADJUST
Laser power adjustment
LDPWR CHECK
Laser power check
EFBAL ADJUST
Traverse (E-F balance) adjustment
FBIAS ADJUST
Focus bias adjustment
FBIAS CHECK
Focus bias check
CPLAY MODE
Continuous playback mode
CREC MODE
Continuous recording mode
DETRK CHECK
Detrack check
Scurve CHECK
S curve check (*1)
EEP MODE
Non-volatile memory mode (*1)
MANUAL CMD
Manual command transfer mode (*1)
SVDATA READ
Data reading out mode (*1)
– 31 –
4-6.
OPERATING THE CONTINUOUS PLAYBACK
MODE
MODE
4-6-1.
Entering the Continuous Playback Mode
1. Set the disc in the unit. (Whichever recordable discs or discs
for playback only are available.)
2. Press the
= 0 button or ) + button and display
“CPLAY MODE”.
3. Press the YES button to change the display to “CPLAY MID”.
4. When access completes, the display changes to
4. When access completes, the display changes to
“C1=
AD=
”.
Note: The numbers “
” displayed show you error rates and ADER.
4-6-2.
Changing the Parts to be Played-back
1. Press the YES button during continuous playback to change
the display as below.
2. When access completes, the display changes to
“C1=
AD=
”.
Note: The numbers “
” displayed show you error rates and ADER.
4-6-3.
Ending the Continuous Playback Mode
1. Press the NO button. The display will change to “CPLAY
MODE”.
2. Press the
6 button and remove the disc.
Notes:
1. The playback start address for IN, MID, and OUT are as fol-
1. The playback start address for IN, MID, and OUT are as fol-
lows.
IN
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
In case you want to display the address of the playback posi-
tion on the display, press the DISPLAY button and display
“CPLAY (
OUT : 700h cluster
In case you want to display the address of the playback posi-
tion on the display, press the DISPLAY button and display
“CPLAY (
)”.
2. The NO button can be used to stop playing anytime.
4-7.
OPERATING THE CONTINUOUS RECORDING
MODE
MODE
4-7-1. Entering the Continuous Recording Mode
1. Set the MO disc in the unit. (Refer to note 3.)
2. Press the
2. Press the
= 0 button or ) + button and display
“CREC MODE”.
3. Press the YES button to change the display to “CREC MID”.
4. When access completes, the display changes to “CREC (
4. When access completes, the display changes to “CREC (
)”
and PRESET lights up.
Note: The numbers “ ” displayed shows you the recording posi-
tion address.
4-7-2.
Changing the Parts to be Recorded
1. When the YES button is pressed during continuous record-
ing, the display changes as below. ( PRESET indication turns
off during change-over of display.)
off during change-over of display.)
2. When access completes, the display changes to “CREC (
)”
and PRESET lights up.
Note: The numbers “ ” displayed shows you the recording posi-
tion address.
4-7-3.
Ending the Continuous Recording Mode
1. Press the NO button. The display will change to “CREC
MODE” and PRESET goes off.
2. Press the
6 button and remove the disc.
Notes:
1. The recording start address for IN, MID, and OUT are as fol-
1. The recording start address for IN, MID, and OUT are as fol-
lows.
IN
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
OUT : 700h cluster
2. The NO button can be used to stop recording anytime.
3. During the test mode, the erasing-protection tab will not be
3. During the test mode, the erasing-protection tab will not be
detected. Therefore be careful not to set the continuous re-
cording mode when a disc not to be erased is set in the unit.
cording mode when a disc not to be erased is set in the unit.
4. Do not perform continuous recording for long periods of time
above 5 minutes.
5. During continuous recording, be careful not to apply vibra-
tion.
CPLAY MID
CPLAY OUT
CPLAY IN
CREC MID
CREC OUT
CREC IN
– 32 –
Mode
display
Error rate
display
Address display
ADIP address
display
SUB Q address
display
Auto gain
display
IVR
display
Change over the display with the
SCROLL button.
SCROLL button.
4-8.
EEP MODE
This mode reads and writes the contents of the non-volatile
memory.
It is not used in servicing. If set accidentally, press the NO button
immediately to exit it.
memory.
It is not used in servicing. If set accidentally, press the NO button
immediately to exit it.
1. MODE display
Displays “TEMP ADJUST”, “CPLAY MODE”, etc..
2. Error rate display
Error rates are displayed as follows.
C1=
C1=
AD=
C1= : Indicates C1 error
AD= : Indicates ADER
AD= : Indicates ADER
3. Address display
Address are displayed as follows.
h=
h=
a=
(MO groove)
With this display, if SCROLL button is pressed, the follow-
ing will be displayed.
h=
ing will be displayed.
h=
s=
(MO pit and CD)
h=: Header address
s=: SUB Q address
a=: ADIP address
s=: SUB Q address
a=: ADIP address
Note: “—” is displayed when the address cannot be read.
4. Auto gain display
Auto gain are displayed as follows.
AGF=
AGF=
T=
F= Focus auto gain collection value
T= Tracking auto gain collection value
T= Tracking auto gain collection value
4-11.
MEANINGS OF OTHER DISPLAYS
Table 4-4.
Note: Auto gain display and IVR display are not used in servicing.
Note: The erasing-protection tab in not detected during the test
mode. Recording will start regardless of the position of
the erasing-protection tab when the
the erasing-protection tab when the
r REC button is
pressed.
4-10.
TEST MODE DISPLAYS
Each time the DISPLAY button pressed, the display changes in
the following order.
the following order.
Light
Off
MANUAL
During continuous
playback (servo all
on)
playback (servo all
on)
Stop state
(servo all off)
(servo all off)
—
AUTO
Tracking and sled
servo off
servo off
Tracking and
sled servo on
sled servo on
—
PRESET
Recording mode on
Recording
mode off
mode off
—
REPEAT
CLV lock state
CLV unlock
state
state
—
TRACK
Pit mode
Groove mode
—
DISC
High reflection rate
disc
disc
Low reflection
rate disc
rate disc
—
LEVEL-
SYNC
Spindle servo
CLV-S
(pull-in mode)
CLV-S
(pull-in mode)
Spindle servo
CLV-A
(playing mode)
CLV-A
(playing mode)
—
PGM
ABCD adjustment
completed
completed
Not adjustment
—
SHUFFLE
Focus auto gain
and tracking auto
gain successful
and tracking auto
gain successful
—
Focus auto
gain suc-
cessful,
tracking
auto gain
failed
gain suc-
cessful,
tracking
auto gain
failed
Display
Blinking
Contents
Table 4-3.
Button
Contents
(P
Sets continuous playback when pressed in the
STOP state. (servo all on)
When pressed during continuous playback, the
tracking and sled servo turns on/off.
STOP state. (servo all on)
When pressed during continuous playback, the
tracking and sled servo turns on/off.
p
Stop continuous playback and continuous
recording. (servo all off)
recording. (servo all off)
VOL +
The sled moves to the outer circumference
only when this is pressed.
only when this is pressed.
VOL –
The sled moves to the inner circumference
only when this is pressed.
only when this is pressed.
r REC
Turns recording on/off when pressed during
continuous playback.
continuous playback.
SCROLL
Switches between the pit and groove modes
when pressed.
when pressed.
BAND
Switches between the CLV-S (pull-in mode)
and CLV-A (playing servo) modes when
pressed. (Switches the spindle servo mode.)
and CLV-A (playing servo) modes when
pressed. (Switches the spindle servo mode.)
DISPLAY
Switches the display when pressed.
Returns to previous step. Stop operations.
Returns to previous step. Stop operations.
6
Disc eject
4-9.
FUNCTIONS OF OTHER BUTTONS
Click on the first or last page to see other HMD-M11 service manuals if exist.