Sony HCD-XGV10AV / HCD-XGV6 / HCD-XGV8 / LBT-XGV10AV / LBT-XGV6 / LBT-XGV8 Service Manual ▷ View online
16
HCD-XGV6/XGV8/XGV10AV
SECTION 4
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure:
1.Turn the power ON or set to the DEMO mode.
2.Press three buttons of c/CLOCK SET , TUNER ENTER , and
1.Turn the power ON or set to the DEMO mode.
2.Press three buttons of c/CLOCK SET , TUNER ENTER , and
\/1 simultaneously.
3. The set is reset, and displays “COLD RESET”, then becomes
DEMO mode.
[Change-over the AM Tuning Interval]
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1.Press the \/1 button to turn the power ON.
2.Select the function “TUNER”, and press the TUNER/BAND
Procedure:
1.Press the \/1 button to turn the power ON.
2.Select the function “TUNER”, and press the TUNER/BAND
button to select the BAND “AM”.
3. Press the \/1 button to turn the power OFF.
4. Press the ENTER/NEXT and \/1 buttons simultaneously,
4. Press the ENTER/NEXT and \/1 buttons simultaneously,
and the display on the fluorescent indicator tube changes to
“AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning
interval is changed over.
“AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning
interval is changed over.
[CD Ship Mode] (No memory clear)
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
after repair.
Procedure:
1.Press the \/1 button to turn the power ON.
2. Press the EDIT and \/1 buttons simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
1.Press the \/1 button to turn the power ON.
2. Press the EDIT and \/1 buttons simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Mode]
Procedure:
1. Press three buttons of c/CLOCK SET , ENTER/NEXT ,
1. Press three buttons of c/CLOCK SET , ENTER/NEXT ,
and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3.Press the DISC 1 button, the MODE and DESTINATION are
3.Press the DISC 1 button, the MODE and DESTINATION are
displayed fluorescent indicator tube.
4.Each time the DISC 1 button is pressed, the MC/GC category
version is displayed in the following order.
5.Press the DISC 2 button, and the key check mode is acti-vated.
6. In the key check mode, the fluorescent indicator tube displays
“K 0 J0 V0”. Each time a button is pressed, “K” value in-creases
to “K69”call the button is pressed.However, once a button is
pressed, it is no longer taken into account.
“J” value increases like 1, 2, 3 ... if turn the . AMS > JOG
dial clock-wise,or it decreases like 0, 9, 8 ... if turn the
. AMS > JOG dial counter-clockwise.
“V” value increases like 1, 2, 3 ... if turn the VOLUME dial
clockwise (“+” direction), or it decreases like 0, 9, 8 ... if turn the
VOLUME dial counterclockwise (“–” direction).
to “K69”call the button is pressed.However, once a button is
pressed, it is no longer taken into account.
“J” value increases like 1, 2, 3 ... if turn the . AMS > JOG
dial clock-wise,or it decreases like 0, 9, 8 ... if turn the
. AMS > JOG dial counter-clockwise.
“V” value increases like 1, 2, 3 ... if turn the VOLUME dial
clockwise (“+” direction), or it decreases like 0, 9, 8 ... if turn the
VOLUME dial counterclockwise (“–” direction).
7. To release from this mode, press three buttons in the same
manner as step 1, or disconnect the power cord.
NR
MC
GC
CD
CDDM
CDMA
CDMB
BDA
BDB
ST
TA
TM
TC
[Sled Servo Mode] (CD service mode)
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons c/CLOCK SET , TUNER ENTER , and
1. Select the function “CD”.
2. Press three buttons c/CLOCK SET , TUNER ENTER , and
DISC 5 simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press M button in CD section to
move the pick-up to outside track, or m button to inside track.
5. To exit from this mode, press \/1 button turn to the power OFF.
Note:
• Always move the pick-up to most inside track when exiting from
Note:
• Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[Change-over of FUNCTION Name]
• The FUNCTION name of external input terminal can be changed
over to VIDEO or MD. With the FUNCTION selected to “MD”,
about 5dB mute is applied to the input gain.
about 5dB mute is applied to the input gain.
Procedure:
1. Press \/1 button to turn the power OFF.
2. Press \/1 button together with FUNCTION button for
1. Press \/1 button to turn the power OFF.
2. Press \/1 button together with FUNCTION button for
several seconds, and the power is turned on, the display of
fluorescent indicator tube changes to “MD” or “VIDEO”
instantaneously, and thus the FUNCTION is changed over.
fluorescent indicator tube changes to “MD” or “VIDEO”
instantaneously, and thus the FUNCTION is changed over.
[Aging Mode]
This mode can be used for operation check of tape deck section.
Tape deck section work in parallel.
• If an error occurred:
Tape deck section work in parallel.
• If an error occurred:
The aging operation stops and display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1.Load the tapes into the decks A and B respectively.
2.Press the FUNCTION button to select the function “CD”.
3.Press the PLAY MODE button to set the “ALL DISCS” mode,
1.Load the tapes into the decks A and B respectively.
2.Press the FUNCTION button to select the function “CD”.
3.Press the PLAY MODE button to set the “ALL DISCS” mode,
and press the REPEAT button to “REPEAT” off.
4. Press three buttons of c/CLOCK SET , TUNER ENTER ,
and DISC 4 simultaneously.
5. The aging mode is activated, if the indicator of disc tray num-
ber on the fluorescent indicator tube is blinking.
6. To release from the aging mode, press the \/1 button to turn
the power OFF and operate the cold reset. (Refer to the “MC
Cold Reset”)
Cold Reset”)
1. Display at the Aging Mode
• Display operating state of tape deck section alternately.
• If an error occurred, stop display.
• If an error occurred, stop display.
17
HCD-XGV6/XGV8/XGV10AV
FWD the tape A
“TAPE A AG-2”
Fast forward the tape A
“TAPE A AG-3”
RVS the tape A
“TAPE A AG-4”
Rewind the tape A
“TAPE A AG-5”
FWD the tape B
“TAPE B AG-2”
Rewind the tape A
“TAPE A AG-1”
Fast forward the tape B
“TAPE B AG-3”
RVS the tape B
“TAPE B AG-4”
Rewind the tape B
“TAPE B AG-5”
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
Aging mode sequence (Tape deck section):
2. Tape Deck Section
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
• If an error occurred, stop display that step.
Note:
“TAPE * AG- * ” is display of each step.
3. CD Section
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
• If an error occurred, stop display that step.
Aging mode sequence (CD section):
DISC 1
chucking
TOC Read
Track 1 Play
Tray Tun
Tray Turn
DISC 4
Chucking
2 seconds
Last Track Play
TOC Read
Track 1 Play
Last Track play
[VACS ON/OFF]
• The volume control by VACS is turned ON/OFF.
Procedure:
1.Press the \/1 button to turn the power ON.
2.Press the PLAY MODE and \/1 buttons simultaneously.
3.The reaction display appears when switcing ON/OFF.
Procedure:
1.Press the \/1 button to turn the power ON.
2.Press the PLAY MODE and \/1 buttons simultaneously.
3.The reaction display appears when switcing ON/OFF.
2 seconds
2 seconds
18
HCD-XGV6/XGV8/XGV10AV
Torque Measurement
Mode
Torque Meter
Meter Reading
2.9~6.9 mN•m
FWD
(30 to 70 g•cm)
(0.42 – 0.97 oz•inch)
FWD
CQ-102C
0.19~0.59 mN•m
back tension
(2 to 6 g•cm)
(0.03 – 0.08 oz•inch)
7.8~16.7 mN•m
FF/REW
CQ-201B
(80 to 170 g•cm)
(1.11 – 2.36 oz • inch)
SECTION 5
MECHANICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION 0 DB = 0.775 V
Precaution
1. Demagnetize the record/playback head with a head demagne-
tizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)
adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless other-wise
7. Switches and controls should be set as follows unless other-wise
specified.
8. Set to the DOLBY NR OFF.
9. Set to the test mode.
9. Set to the test mode.
(1) Press the \/1 button to turn the power ON.
(2) Select the function “TAPE A or B”.
(2) Select the function “TAPE A or B”.
(3) Press the button of c/CLOCK SET , TUNER ENTER ,
and DISC 3 simultaneously, to set the tape deck test mode
and displays “TEST MODE” on the fluorescent indicator
tube.
and displays “TEST MODE” on the fluorescent indicator
tube.
(4) To release from the test mode, press the \/1 button.
• Test Tape
Tape
Signal
Used for
P-4-A100
10 kHz, – 10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
19
HCD-XGV6/XGV8/XGV10AV
Record/Playback Head Azimuth Adjustment
DECK A DECK B
Note:
Note:
Perform this adjustments for both decks
Procedure:
1. Mode: Playback (FWD)
1. Mode: Playback (FWD)
set
MAIN board
MD (VIDEO) OUT jack (J701)
L-CH, R-CH
MD (VIDEO) OUT jack (J701)
L-CH, R-CH
+
level meter
test tape
P-4-A100
(10 kHz, – 10 dB)
P-4-A100
(10 kHz, – 10 dB)
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
3. Mode: Playback
set
test tape
P-4-A100
(10 kHz, – 10 dB)
P-4-A100
(10 kHz, – 10 dB)
R-CH
oscilloscope
L-CH
R-CH
V
H
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good
wrong
MAIN board
MD (VIDEO) OUT jack (J701)
L-CH
MD (VIDEO) OUT jack (J701)
L-CH
4. Repeat step 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck
B).
Tape Speed Adjustment DECK B
Mode: Playback
+
–
–
set
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
MAIN board
MD (VIDEO) OUT jack (J701)
L-CH, R-CH
MD (VIDEO) OUT jack (J701)
L-CH, R-CH
frequency counter
1. Insert the WS-48B into the deck B.
2. Press the H button on the deck B.
3. Press the H SPEED DUB button in playback mode.
2. Press the H button on the deck B.
3. Press the H SPEED DUB button in playback mode.
Then at HIGH speed mode.
4. Adjust RV392 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
5. Press the H SPEED DUB button.
Then back to NORMAL speed mode.
6. Adjust RV391 on the LEAF SW board so that frequency
counter reads 3,000 ± 90 Hz.
Adjustment Location: MAIN board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
forward
reverse
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
Click on the first or last page to see other HCD-XGV10AV / HCD-XGV6 / HCD-XGV8 / LBT-XGV10AV / LBT-XGV6 / LBT-XGV8 service manuals if exist.