Sony HCD-XGV10AV / HCD-XGV6 / HCD-XGV8 / LBT-XGV10AV / LBT-XGV6 / LBT-XGV8 Service Manual ▷ View online
2
HCD-XGV6/XGV8/XGV10AV
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Outputs
PHONES:
(stereo phone jack)
PHONES:
(stereo phone jack)
accepts headphones of 8 ohms or more
MD (VIDEO) OUT:
(phono jacks)
(phono jacks)
voltage 250 mV
impedance 1 kilohms
impedance 1 kilohms
LBT-XGV10AV
WOOFER OUT (phono jack):
voltage 1 V, impedance 1 kilohm
FRONT SPEAKER:
accepts impedance of 6 to 16 ohms
CENTER SPEAKER:
accepts impedance of 8 to 16 ohms
REAR SPEAKER:
accepts impedance of 8 to 16 ohms
LBT-XGV8
FRONT SPEAKER:
accepts impedance of 6 to 16 ohms
(SUPER WOOFER)
accepts impedance of 6 to 16 ohms
(TWEETER & WOOFER)
(SUPER WOOFER)
accepts impedance of 6 to 16 ohms
(TWEETER & WOOFER)
LBT-XGV6
FRONT SPEAKER:
accepts impedance of 6 to 16 ohms
Video section
Inputs
GAME INPUT (phono jack):
GAME INPUT (phono jack):
1 V p-p, 75 ohms
Outputs
VIDEO OUT (phono jack):
VIDEO OUT (phono jack):
1 V p-p, 75 ohms
VIDEO CD/CD player section
System
Compact disc and digital audio system
Laser
Semiconductor laser
(
(
λ
=795nm), Emission
duration: continuous
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
Video color system format
NTSC, PAL
Tape player section
Recording system
4-track 2-channel stereo
Frequency response
40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
using Sony TYPE I cassette
Wow and flutter
±0.15% W.Peak (IEC)
0.1% W.RMS (NAB)
±0.2% W.Peak (DIN)
0.1% W.RMS (NAB)
±0.2% W.Peak (DIN)
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50 kHz step)
(50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Middle Eastern model:
Middle Eastern model:
531 – 1,602 kHz
(with the interval set at 9 kHz)
(with the interval set at 9 kHz)
Other models:
531 – 1,602 kHz
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
Saudi Arabian model:
Saudi Arabian model:
120 – 127 V, 220 V or 230 – 240 V AC,
50/60 Hz
Adjustable with voltage selector
50/60 Hz
Adjustable with voltage selector
Thai model:
220 V AC, 50/60 Hz
Other models:
120 V, 220 V or 230 –240 V AC,
50/60 Hz
Adjustable with voltage selector
50/60 Hz
Adjustable with voltage selector
Power consumption
LBT-XGV10AV
LBT-XGV10AV
230 watts
LBT-XGV8
320 watts
LBT-XGV6
180 watts
Dimensions (w/h/d)
Approx. 355 x 425 x 451 mm
Mass:
LBT-XGV10AV
LBT-XGV10AV
Approx. 15.4 kg
LBT-XGV8
Approx. 16.4 kg
LBT-XGV6
Approx. 14.7 kg
Supplied accessories:
AM loop antenna (1)
FM lead antenna (1)
Speaker cords (XGV6, XGV8 (4),
XGV10AV (5))
Speaker pads (XGV6, XGV8 (8),
XGV10AV (12))
Remote commander (1)
Batteries (2)
Video connecting cable (1)
FM lead antenna (1)
Speaker cords (XGV6, XGV8 (4),
XGV10AV (5))
Speaker pads (XGV6, XGV8 (8),
XGV10AV (12))
Remote commander (1)
Batteries (2)
Video connecting cable (1)
Design and specifications are subject to change witho fi notice.
3
HCD-XGV6/XGV8/XGV10AV
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
check that the S curve waveforms is output three times.
• MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
MODEL
XGV10AV : SP model
XGV10AV : TH model
XGV8 : SP model
XGV6 : TH model
XGV6 : SP model
XGV10AV : EA model
PARTS No.
4-238-825-2
s
4-238-825-3
s
4-238-825-4
s
4-238-825-5
s
4-238-825-6
s
4-238-825-7
s
PART No.
TABLE OF CONTENTS
1. SERVICING NOTE
·························································· 4
2. GENERAL
·········································································· 5
3. DISASSEMBY
··································································· 8
4. TEST MODE
···································································· 16
5. MECHANICAL ADJUSTMENTS
····························· 18
6. ELECTRICAL ADJUSTMENTS
······························· 18
7. DIAGRAMS
7-1. Circuit Board Location ······················································ 23
7-2. Block Diagram – CD Servo Section – ······························· 24
7-2. Block Diagram – CD Servo Section – ······························· 24
Block Diagram – Tuner/Tape Deck Section – ··················· 25
Block Diagram – Main Section – ······································ 26
Block Diagram
Block Diagram – Main Section – ······································ 26
Block Diagram
– Display/Key Control/Power Supply Section – ·········· 27
7-3. Printed Wiring Board – BD Section – ······························· 28
7-4. Schematic Diagram – BD Section – ·································· 29
7-5. Schematic Diagram –Video (1/2) Section – ······················ 30
7-6. Schematic Diagram –Video (2/2) Section – ······················ 31
7-7. Printed Wiring Board – Video Section – ··························· 32
7-8. Printed Wiring Board – Motor, LED Section – ················· 33
7-9. Schematic Diagram –Motor, LED Section – ····················· 33
7-10. Schematic Diagram – Main (1/3) Section – ······················ 34
7-11. Schematic Diagram – Main (2/3) Section – ······················ 35
7-12. Schematic Diagram – Main (3/3) Section – ······················ 36
7-13. Printed Wiring Board – Main Section – ···························· 37
7-14.Printed Wiring Board
7-4. Schematic Diagram – BD Section – ·································· 29
7-5. Schematic Diagram –Video (1/2) Section – ······················ 30
7-6. Schematic Diagram –Video (2/2) Section – ······················ 31
7-7. Printed Wiring Board – Video Section – ··························· 32
7-8. Printed Wiring Board – Motor, LED Section – ················· 33
7-9. Schematic Diagram –Motor, LED Section – ····················· 33
7-10. Schematic Diagram – Main (1/3) Section – ······················ 34
7-11. Schematic Diagram – Main (2/3) Section – ······················ 35
7-12. Schematic Diagram – Main (3/3) Section – ······················ 36
7-13. Printed Wiring Board – Main Section – ···························· 37
7-14.Printed Wiring Board
– CD-L,CD-R,Headphone,Front Input,D-SW Section – ·· 38
7-15.Schematic Diagram
– CD-L,CD-R,Headphone,Front Input,D-SW Section – ·· 39
7-16.Printed Wiring Board – Panel VR Section – ······················ 40
7-17. Schematic Diagram – Panel VR Section – ························ 41
7-18. Printed Wiring Board – Panel FL,TC-A,TC-B Section – · 42
7-19. Schematic Diagram – Panel FL,TC-A,TC-B Section – ····· 43
7-20. Printed Wiring Board – PA Section (XGV10AV) – ··········· 44
7-21. Schematic Diagram – PA Section (XGV10AV) – ············· 45
7-22. Printed Wiring Board – PA Section (XGV6/XGV8) – ······ 46
7-23. Schematic Diagram – PA Section (XGV6/XGV8) – ········· 47
7-24. Schematic Diagram – Sub Amp Section (XGV10AV) – ·· 48
7-25. Schematic Diagram – Sub Amp Section (XGV8) – ·········· 49
7-26. Printed Wiring Board
7-17. Schematic Diagram – Panel VR Section – ························ 41
7-18. Printed Wiring Board – Panel FL,TC-A,TC-B Section – · 42
7-19. Schematic Diagram – Panel FL,TC-A,TC-B Section – ····· 43
7-20. Printed Wiring Board – PA Section (XGV10AV) – ··········· 44
7-21. Schematic Diagram – PA Section (XGV10AV) – ············· 45
7-22. Printed Wiring Board – PA Section (XGV6/XGV8) – ······ 46
7-23. Schematic Diagram – PA Section (XGV6/XGV8) – ········· 47
7-24. Schematic Diagram – Sub Amp Section (XGV10AV) – ·· 48
7-25. Schematic Diagram – Sub Amp Section (XGV8) – ·········· 49
7-26. Printed Wiring Board
– Sub Amp Section (XGV10AV/XGV8) – ························· 50
7-27. Schematic Diagram – MIC/Guitar Section – ····················· 51
7-28. Printed Wiring Board – MIC/Guitar Section – ·················· 51
7-29. Printed Wiring Board – Prologic Section (XGV10AV) – ·· 52
7-30. Schematic Diagram – Prologic Section (XGV10AV) – ···· 53
7-31. Printed Wiring Board – Trans,Sub Trans Section – ·········· 54
7-32. Schematic Diagram – Trans,Sub Trans Section – ·············· 55
7-33. IC Pin Function Description ············································· 56
7-34. IC Block Diagram ····························································· 63
7-28. Printed Wiring Board – MIC/Guitar Section – ·················· 51
7-29. Printed Wiring Board – Prologic Section (XGV10AV) – ·· 52
7-30. Schematic Diagram – Prologic Section (XGV10AV) – ···· 53
7-31. Printed Wiring Board – Trans,Sub Trans Section – ·········· 54
7-32. Schematic Diagram – Trans,Sub Trans Section – ·············· 55
7-33. IC Pin Function Description ············································· 56
7-34. IC Block Diagram ····························································· 63
8. EXPLODED VIEWS
8-1. Case,Back Panel Section ··················································· 66
8-2. Front Panel Section-1 ························································ 67
8-3. Front Panel Section-2 ························································ 68
8-4. Chassis Section ·································································· 69
8-5. CD Mechanism Deck Section
(CDM37B-30BD62) ··························································· 70
8-6. Base Unit Section (BU-30BD62) ······································ 71
8-2. Front Panel Section-1 ························································ 67
8-3. Front Panel Section-2 ························································ 68
8-4. Chassis Section ·································································· 69
8-5. CD Mechanism Deck Section
(CDM37B-30BD62) ··························································· 70
8-6. Base Unit Section (BU-30BD62) ······································ 71
9. ELECTRICAL PARTS LIST
······································· 72
• Abbreviation
SP : Singapore model
TH : Thai model
EA : Saudi Arabia model
TH : Thai model
EA : Saudi Arabia model
4
HCD-XGV6/XGV8/XGV10AV
SECTION 1
SERVICING NOTE
JIG FOR CHECKING PROLOGIC BOARD (XGV10AV ONLY)
CN201
MAIN board
CN151
CN152
CN202
PROLOGIC board
Jig (J-2501-216-A)
The special jig (J-2501-216-A) is useful for checking the PROLOGIC board.
5
HCD-XGV6/XGV8/XGV10AV
This section is extracted from
instruction manual.
instruction manual.
SECTION 2
GENERAL
ALPHABETICAL ORDER
E — K
ECHO LEVEL ej
EDIT ef
EFFECT 5
ENTER 5
FM MODE 8
FUNCTION qd
EDIT ef
EFFECT 5
ENTER 5
FM MODE 8
FUNCTION qd
GAME qf
GAME INPUT AUDIO L/R jacks
wf
GAME INPUT VIDEO jack wf
GAME MIXING qg
GROOVE ra
H SPEED DUB ql
KARAOKE PON/MPX ea
KEY CONTROL #/ 2 ea
GAME MIXING qg
GROOVE ra
H SPEED DUB ql
KARAOKE PON/MPX ea
KEY CONTROL #/ 2 ea
M — R
MIC LEVEL ej
MIC 1/2 jacks eh
NEXT wd
P FILE 5
PHONES jack w;
PICTURE EFFECT wd
PLAY MODE eg
POWER SAVE/DEMO
MIC 1/2 jacks eh
NEXT wd
P FILE 5
PHONES jack w;
PICTURE EFFECT wd
PLAY MODE eg
POWER SAVE/DEMO
(STANDBY) 3
Power stream indicator 6
PREV wd
PRO LOGIC wg (XGV10AV)
PUSH OPEN wk
REPEAT eg
RETURN O wd
PREV wd
PRO LOGIC wg (XGV10AV)
PUSH OPEN wk
REPEAT eg
RETURN O wd
Main unit
wf
wg
wh
wj
wl
e;
ea
es
ed
ef
eg
eh
ej
ek
r;
ra
el
wk
qf
qd
23 4 5
7
6
890 qa qs
qg
qh
qj
qk
ql
w;
wa
ws
wd
1
A — D
A EJECTZ/ Z B EJECT wl
ALBUM +/—
ALBUM +/—
ed
CD SYNC ql
Direct equalizer qh r;
Direct equalizer qh r;
POP/ROCK/JAZZ/DANCE/
GAME
SALSA/REGGAE/TANGO/
SAMBA/MOVIE
GAME
SALSA/REGGAE/TANGO/
SAMBA/MOVIE
DIRECTION ek
DISC SKIP eg
DISC 1 to 5 es
DISPLAY 2
DSP ra (XGV10AV)
DVD 5.1CH wg (XGV10AV)
DISC SKIP eg
DISC 1 to 5 es
DISPLAY 2
DSP ra (XGV10AV)
DVD 5.1CH wg (XGV10AV)