DOWNLOAD Sony HCD-XB88AVK / HCD-XB88K / LBT-XB88AVK / LBT-XB88KS Service Manual ↓ Size: 8.28 MB | Pages: 86 in PDF or view online for FREE

– 10 –

• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the

customer.

Procedure:
1. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  DISC 1  simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press  1/u  button to turn the set ON.
2. Press  PLAY MODE  button and  1/u  button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

• This mode resets the set with the preset data kept stored in the memory.  The hot reset mode functions same as if the power cord is plugged

in and out.

Procedure:
1. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  DISC 2  simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  FUNCTION  simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, press  )  button in CD section to move the pick-up to outside track, or  0  button to inside track.
5. To exit from this mode, perform as follows:

1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.

Note:
• Always move the pick-up to most inside track when exiting from this mode.  Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.

• The FUNCTION name of external input terminal can be changed over to VIDEO or MD. With the FUNCTION selected to “MD”, about

5dB mute is applied to the input gain.

Procedure:
1. Press  1/u  button to turn the set OFF.
2. Press  1/u  button together with  FUNCTION  button, and the power is turned on, the display of fluorescent indicator tube changes to

“MD” or “VIDEO” instantaneously, and thus the FUNCTION is changed over.

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press  1/u  button to turn the set ON.
2. Select the function “TUNER”, and press  TUNER/BAND  button to select the BAND “AM”.
3. Press  1/u  button to turn the set OFF.
4. Press  ENTER/NEXT  and  1/u  buttons simultaneously, and the display of  fluorescent indicator tube changes to “AM 9k STEP” or “AM

10k STEP”, and thus the channel step is changed over.

Procedure:
1. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  DISC 3  simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.

Press  DISC 2  button, and the key check mode is activated.

3. In the key check mode, the fluorescent indicator tube displays “K 1 V0 J0”.  Each time a button is pressed, “K”value increases. However,

once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating  VOLUME  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.

4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

– 11 –

This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:

The aging operation stops.

• If no error occurs:

The aging operation continues repeatedly.

1-1. Operating procedure of Aging Mode

1. Set discs in DISC 1 and DISC 3 trays.
2. Select the function “CD”.
3. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  KARAOKE PON/MPX  simultaneously.
4. The aging mode is activated, if a roulette mark on the fluorescent indicator tube is blinking.
5. In the aging mode, the aging is executed in a sequence given in “1-2. Operation during Aging Mode”.

The aging continues unless an alarm occurred.

6. To exit from the aging mode, press  1/u  button to turn the set OFF.

• If a button other than buttons In CD section is pressed during aging, the aging in the CD section is finished.
• To execute aging to the tape deck section successively, press  ·  button in the deck A.

“AGING” is displayed on the fluorescent indicator tube.  (For the aging in tape deck, see “2. Aging Mode in Tape Deck Section”.

1-2.  Operation during aging Mode
In the aging mode, the program is executed in the following sequence.

1. The disc tray turns to select a disc. (For a disc selection sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pick-up accesses to the last track.
4. Steps 1 through 3 are repeated.

1-3.  Disc Selection Sequence

• During the aging mode, discs are selected in the following sequence:

Disc 1 

→

 Disc 3

↑

↓

Disc 3 

←

 Disc 1

2-1.  Operating procedure of Aging Mode

1. Load a commercially available 10-minute tape into the decks A and B respectively.

(If a 10-minute tape is not available, another tape may be used but a cycle time will be longer.)

2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing  0  button respectively on decks A and B.
4. Press three buttons  SPECTRUM ANALYZER  ,  ENTER  , and  KARAOKE PON/MPX  simultaneously.
5. Press  ·  button on deck A.  (This button triggers the aging mode.)
6. The aging mode is activated if “AGING A” is displayed on the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence given in “2-2.  Operation during Aging Mode”.

The aging continues unless an alarm occurred.

8. To exit from the aging mode, press  1/u  button to turn the set OFF.

2-2.  Operation during Aging Mode
In the aging mode, the program is executed in the following sequence.

1. A tape on FWD side is played for one minute.
2. PAUSE STOP is made.
3. Recording is made for 3 minutes. (For the deck not having the record function, the play is executed.)
4. FF is executed up to the end of tape.
5. A tape is reversed, and the tape on REV side is played for one minute.
6. PAUSE STOP is made.
7. Recording is made for 3 minutes.  (For the deck not having the record function, the play is executed.)
8. FF is executed up to the end of tape.
9. Steps 1 through 8 are executed for the other deck.
10. Steps 1 through 9 are repeated unless an alarm occurred.

2-3.  Deck Selection Sequence

• During the aging mode, decks are selected in the following sequence:

Deck A (FWD) 

→

 Deck A (REV)

↑

↓

Deck B (REV) 

←

 Deck B (FWD)

– 12 –

1. Clean the following parts with a denatured alcohol-moistened

swab:

record/playback heads pinch rollers
erase head rubber belts
capstan idlers

2. Demagnetize the record/playback head with a head demagne-

tizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

2 to 6 g • cm

(0.02 - 0.08 oz • inch)

36 to 61 g • cm

(0.5 - 0.84 oz • inch)

Mode Torque meter

FWD

FWD
back tension

REV

FF/REW

REV
back tension

FWD tension

REV tension

CQ-102C

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

36 to 61 g • cm

(0.5 - 0.84 oz • inch)

2 to 6 g • cm

(0.02 - 0.08 oz • inch)

61 to 143 g • cm

(0.85 - 1.99 oz • inch)

100 g or more

(3.53 oz or more)

100 g or more

(3.53 oz or more)

Meter reading

1. Demagnetize the record/playback head with a head damagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjusted.

4. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this

service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit adjust-
ment.)

6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise

specified.

Note: Perform this adjustments for both decks.

Procedure:
1. Mode : Playback

Signal

Used for

Tape

Azimuth Adjustment

Tape Speed Adjustment

Level Adjustment

10 kHz, –10 dB

3 kHz, 0 dB

315 Hz, 0 dB

P-4-A100

WS-48B

P-4-L300

test tape
P-4-A100
(10kHz, –10dB)

main board
CN403
Pin 

3

 (L-CH)

Pin 

1

 (R-CH)

level meter

set

main board
CN403
Pin 

2

 (GND)

– 13 –

4. After the adjustments, apply suitable locking compound to the

parts adjusted.

Adjustment Location: Playback Head (Deck A)

Record/Playback/Erase Head (Deck B)

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.

3. Mode: Playback

Note: Set the test mode using the following method and begin tape

speed adjustment.
In the test mode, the tape will move at double speed or normal
speed each time the  H SPEED DUB.  button is pressed.

Procedure :
With the power turned ON, press the  SPECTRUM ANALYZER
button,  ENTER  button, and  EFFECT  button simultaneously.
(The “VOLUME” on the fluorescent display tube will blink while
in the test mode.)
To exit the test mode, press the  1/u  button.

1. Load WS-48B into deck B.
2. Play deck B.
3. Press the  H SPEED DUB.  button and play the tape at double

speed.

4. Adjust RV652 of the AUDIO board so that the reading of the

frequency counter becomes 6000 ± 180 Hz.

5. Press the  H SPEED DUB.  button and play the tape at normal

speed.

6. Adjust RV651 of the AUDIO board so that the reading of the

frequency counter becomes 3000 ± 90 Hz.

Adjustment Location: AUDIO board

W.RMS (JIS) less than 0.3%
(test tape: WS-48B)

Procedure:
Mode: Playback

Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.

Adjustment level:
CN403 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board

L-CH
peak

R-CH
peak

screw
position

output
level

within
1 dB

L-CH
peak

R-CH
peak

screw
position

within 1dB

test tape
P-4-A100
(10kHz, –10dB)

oscilloscope

set

L

R

Waveform of oscilloscope

in phase

45

°

90

°

135

°

180

°

good

wrong

main board
CN403
Pin 

3

 (L-CH)

Pin 

2

 (GND)

Pin 

1

 (R-CH)

reverse

forward

test tape 
P-4-L300
(315Hz, 0dB)

level meter

set

main board
CN403

Pin 

3

 (L-CH)

Pin 

1

 (R-CH)