Sony HCD-VZ10 Service Manual ▷ View online
11
3-7. CD MECHANISM DECK SECTION
(CDM53F-K2BD37A)
3-8. FITTING BASE (GUIDE) ASSY, BRACKET (CHASSIS) AND
FITTING BASE (MAGNET) ASSY
1
three screws
(BVTT 3
(BVTT 3
× 6)
5
CD mechanism deck section
(CDM53F-K2BD37A)
2
two screws
(BVTT 3
(BVTT 3
× 6)
4
four screws
(sumitite (B3), +BV)
(sumitite (B3), +BV)
3
chassis, sub
qs
four screws
(BVTP M2.6)
(BVTP M2.6)
7
four screws
(BVTP M2.6)
(BVTP M2.6)
0
bracket
(chassis)
(chassis)
9
five screws
(BVTP M2.6)
(BVTP M2.6)
qa
connector
(CN710)
(CN710)
1
connector
(CN501)
(CN501)
6
two connectors
(CN709, 715)
(CN709, 715)
qd
base (magnet) assy, fitting
8
base
(guide) assy, fitting
2
screw
(BVTP 3
(BVTP 3
× 8)
4
screw
(BVTP
(BVTP
3
× 8)
3
VIDEO board
5
bracket (VCD)
12
3-9. TRAY (SUB)
3-10. CHASSIS (MOLD B) SECTION, STOCKER SECTION AND
SLIDER (SELECTION)
Note : In mounting the parts, refer to page 12 and 13.
pulley (LD)
stocker
section
section
tray (sub)
pulley (mode)
slider (selection)
1
Rotating the pulley (LD), shift the slider (selection) in the arrow A direction.
2
Rotating the pulley (mode) in the arrow direction, adjust the tray (sub) to be removed.
3
Rotating the pulley (LD), shift the slider (selection) in the arrow B direction.
4
Rotating the pulley (mode) in the arrow direction, remove the tray (sub) to be removed.
A
B
5
stocker
section
section
4
two step
screws
screws
4
two step screws
3
gear (eject)
2
chassis (mold B) section
Note: Rotating the pulley (LD),
shift the slider (selection)
to the left.
to the left.
9
compression
spring
spring
7
slider (selection)
8
washer
6
two screws
(PTPWH M2.6)
(PTPWH M2.6)
1
three screws
(BVTP M2.6)
(BVTP M2.6)
pulley (LD)
13
3-11. GEARS INSTALLATION
3-12. SLIDER (SELECTION) INSTALLATION
1
Slide the slider (U/D)
fully in the arrow
direction.
fully in the arrow
direction.
3
gear (gear B)
2
gear (U/D slider)
4
gear (gear A)
Adjust the gear (gear B) with the
portion A as shown.
portion A as shown.
Adjust the gear so that it meshes with
the bottom tooth of slider (U/D)gear,
as shown.
the bottom tooth of slider (U/D)gear,
as shown.
portion A
slider (U/D) gear
linearly
gear
(gear B)
(gear B)
Adjust so as to be aligned with
gear (B) linearly,as shown.
gear (B) linearly,as shown.
portion A
2
gear (chuking)
6
two screws
(PTPWH M2.6)
(PTPWH M2.6)
5
washer
3
convex portion of
slider (selection)
slider (selection)
4
compression spring
7
Insert the slider (selection)
into the portion A.
into the portion A.
1
rotary encoder
rotary encoder
Align with the slot of
rotary encoder.
rotary encoder.
align marking
gear (chuking)
Insert a convex portion into
a groove of gear (chuking).
a groove of gear (chuking).
14
3-13. STOCKER SECTION INSTALLATION
3-14. CHASSIS (MOLD B) SECTION INSTALLATION
2
portion A of tray (sub)
1
stocker section
3
two step screws
3
two step screws
Hook the portion A of tray (sub)
to the slider (selection).
to the slider (selection).
potion A
of tray (sub)
of tray (sub)
sticking of
slider (selection)
slider (selection)
3
three screws
(BVTP M2.6)
(BVTP M2.6)
2
Insert the gear (eject)
under the gear (LD
deceleration).
under the gear (LD
deceleration).
1
Insert the portion A of
chassis (mold B) section
into the portion B of
slider (selection).
chassis (mold B) section
into the portion B of
slider (selection).
gear (LD deceleration)
portion A
portion B of
slider (selection)
slider (selection)
Click on the first or last page to see other HCD-VZ10 service manuals if exist.