Sony HCD-VX99 / MHC-VX99 Service Manual ▷ View online
6
This section is e
xtracted from
instr
uction manual.
7
Inserting two size AA (R6)
batteries into the remote
batteries into the remote
Using the remote
You can use the shaded buttons shown below
to operate a Sony TV.
to operate a Sony TV.
To
Press
Turn the TV on or off
TV ?/1
Switch the TV's
TV/VIDEO.
video input
Change the TV
TV CH +/–.
channels
Adjusts the volume
TV VOL +/–.
of the TV speaker(s)
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates
the system, replace both batteries with new ones.
six months. When the remote no longer operates
the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of
time, remove the batteries to avoid possible damage
from battery leakage.
time, remove the batteries to avoid possible damage
from battery leakage.
When carrying this system
Do the following to protect the CD
mechanism.
mechanism.
1
Make sure that all discs are removed from
the unit.
the unit.
2
Hold down CD and then press ?/1 so that
“LOCK” appears in the display.
“LOCK” appears in the display.
3
Unplug the AC power cord.
1
Press CLOCK/TIMER SET.
The hour indication flashes.
2
Press . or > repeatedly to set
the hour.
the hour.
Step 2: Setting the
time
time
You must set the time before using the timer
functions.
functions.
continued
N
X
x
x
M
m
>
.
nN
O
v
V
b
B
X
1
3,5
2,4
TV ?/1
TV VOL +/
TV CH +/
TV/VIDEO
8
1
Press TUNER/BAND repeatedly
until the band you want appears in
the display.
until the band you want appears in
the display.
Every time you press this button, the
band changes as follows:
FM y AM
band changes as follows:
FM y AM
Step 3: Presetting
radio stations
radio stations
You can preset 20 stations for FM and 10
stations for AM.
stations for AM.
?/1
(Power)
(Power)
3
Press ENTER.
The minute indication flashes.
4
Press . or > repeatedly to set
the minute.
the minute.
5
Press ENTER.
The clock starts working.
Tip
If you’ve made a mistake, start over from step 1.
To change the time
The previous explanation shows you how to set the
time while the power is off. To change the time
while the power is on, do the following:
1
time while the power is off. To change the time
while the power is on, do the following:
1
Press CLOCK/TIMER SET.
2
Press . or > repeatedly to select
SET CLOCK.
SET CLOCK.
3
Press ENTER.
4
Perform steps 2 through 5 above.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
Step 2: Setting the time
(continued)
(continued)
SHUTTLE
4
2
1
3
7
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
Side panel R
Claw
4
q;
8
Upper case (Top)
Side panel L
5
Two screws (Case)
7
Two screws
(+BVTP 3
× 10)
1
Two screws (Case)
9
Two screws (+BVTP 3
× 10)
3
Two screws
(+BVTP 3
× 10)
6
Screw (Case)
2
Screw (Case)
2
Pull-out the disc tray.
1
Turn the pulley to the direction of arrow.
pulley
Loading panel assy
Front panel side
CD mechanism deck (CDM58)
3
3-1.
UPPER CASE (TOP)
3-2.
LOADING PANEL ASSY
8
6
Tape mechanism deck
5
Five screws (+BVTP 2.6
× 8)
1
Screw (+BVTP 2.6
× 8)
2
Bracket (Heart cam R)
4
Bracket (Heart cam L)
3
Screw (+BVTP 2.6
× 8)
3-3.
FRONT PANEL SECTION
3-4.
TAPE MECHANISM DECK
7
CD mechanism deck (CDM58)
Front panel section
3
Connector (CN2)
8
Connector (CN201)
9
Connector (CN202)
2
Connector (CN1)
Connector
(CN601)
(CN601)
1
Flat type wire (CN304)
6
Three screws (+BVTT 3
× 6)
5
Screw (+BVTP 3
× 10)
4
Screw (+BVTP 3
× 10)
0
Two screws (+BVTP 2.6
× 8)
qs
9
qs
Cut the eleven melted-connection points with a cutting plier.
Note: When attching the panel board,
refer to "Service Note" on page 4.
refer to "Service Note" on page 4.
qf
Panel board
qa
CD Switch board
1
Knob (Volume)
8
5
FR knob
4
Bracket (FR)
qd
Five claws
0
Three claws
9
Three screws
(+BVTP 2.6
× 8)
3
Two bosses & four pins
6
Spring
2
Two screws
(+BVTP 2.6
× 8)
7
Knob(MIC)
8
Two screws
(+BVTT 4
× 8)
2
Six screws
(+BVTP 3
× 10)
1
Two screws
(+BVTP 3
× 10)
4
Panel, back
7
Two screws (+BVTT 4
× 8)
0
Trans board
9
Trans
5
Connector (CN975)
6
Connector (CN977)
3
Connector (CN891)
3-5.
PANEL BOARD
3-6.
TRANS BOARD
Click on the first or last page to see other HCD-VX99 / MHC-VX99 service manuals if exist.