Sony HCD-VX777 Service Manual ▷ View online
3
HCD-VX777
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
of emitting radiation exceeding the limit for
Class 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
MODEL IDENTIFICATION
— BACK PANEL —
PARTS No.
• Abbreviation
EA
: Saudi Arabia model
IA
: Indonesian model
SP
: Singapore model
TH
: Thai model
MODEL
E, EA, SP, IA models
TH model
PARTS No.
4-232-028-1
s
4-232-028-5
s
SETTING THE TIME
This section is extracted
from instruction manual.
from instruction manual.
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
When you set the time for the first time,
proceed to step 5.
proceed to step 5.
3
Press cursor
V/v
repeatedly to select
CLOCK SET.
4
Press ENTER.
5
Press cursor
V/v
repeatedly to set the
hour.
6
Press ENTER.
7
Press cursor
V/v
repeatedly to set the
minute.
8
Press ENTER.
The clock starts working.
If you have made a mistake or want to change the
time, start over from step 2.
time, start over from step 2.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
4
HCD-VX777
Location of Parts and Controls
1
@/1 (POWER) button and indicator
2
DISC 1 button and indicator
3
DISC 2 button and indicator
4
DISC 3 button and indicator
5
DISC SKIP EX-CHANGE button
6
CD (OPEN) button
7
CD button and indicator
8
TUNER/BAND button and indicator
9
TAPE A/B button and indicator
q;
MD (VIDEO) button and indicator
qa
VOLUME knob
qs
PHONES jack
qd
MIC 2 jack
qf
MIC 1 jack
qg
MIC LEVEL knob
qh
ECHO level knob
qj
SURROUND speaker indicator
qk
GAME INPUT (VIDEO, AUDIO L/R) jack
ql
GAME button and indicator
w;
DISPLAY button
wa
SPECTRUM button
ws
EDIT (DIRECTION) button
wd
REPEAT (FM MODE/DOLBY NR) button
SECTION 1
GENERAL
Front Panel
wf
PLAY MODE (TUNER MEMORY) button
wg
Remote sensor
wh
MOVIE EQ button
wj
ENTER button and indicator
wk
P FILE button
wl
M/+ button
e;
REC PAUSE/START button and indicator
ea
> button
es
CD SYNC HI-DUB button
ed
X button
ef
SURROUND button
eg
bB button
eh
x button
ej
GROOVE button
ek
. button
el
m/– button
r;
b/v/B/V button
ra
GAME EQ button
rs
KARAOKE PON button
rd
EFFECT ON/OFF button
rf
MUSIC EQ button
w; wa ws wd wf wg
1
2 3 4
56
7
9
qa
qs
8
q;
ql
qg
qd
qk
elek eh eg ed ea
wl
e;
ej
ef es
rs
rd
r;
ra
rf
wj
wk
wh
qf
qh
qj
5
HCD-VX777
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1. CASE (TOP)
Set
Case (Top)
Loading Panel
Front Panel Section
Tape Mechanism Deck
CD SW Board, Panel Board And PAD Switch Board
Head (A) Board, Head (B) Board And SW Board
Main Trans Board
Main Board And Power Board
Base Unit
Driver Board, Motor Board, CD Sensor Board And Video Board
• The equipment can be removed using the following procedure.
4
qs
9
8
two screws
(+BVTP 3
×
10)
1
two screws (case 3 TP2)
6
two screws (case 3 TP2)
qd
case (top)
7
screw (case 3 TP2)
5
side panel (R)
0
side panel (L)
2
screw (case 3 TP2)
qa
two screws (+BVTP 3
×
10)
two claws
two claws
3
two screws
(+BVTP 3
×
10)
6
HCD-VX777
2-2. LOADING PANEL
2-3. FRONT PANEL SECTION
2
Pull-out the disc tray.
4
Pull-out the disc tray.
1
Turn the pulley to the direction of arrow.
pulley
Front panel side
CD mechanism deck (CDM58)
3
8
3
connector (CN2)
4
connector
(CN607)
0
connector
(CN781)
qa
flat type wire
(CN201)
qs
connector
(CN202)
2
connector (CN1)
connector
(CN401)
(CN401)
1
flat type wire (CN304)
qg
CD mechanism deck (CDM58)
7
three screws (+BVTT 3
×
8)
9
front panel section
5
screw (+BVTP 3
×
10)
qd
screw (+BVTP 3
×
10)
6
screw
(+BVTP 3
×
10)
qf