DOWNLOAD Sony HCD-VX222 / MHC-VX222 Service Manual ↓ Size: 7.01 MB | Pages: 69 in PDF or view online for FREE

7

Note : Disassemble the unit in the order as shown below.

Note : Follow the disassembly procedure in the numerical order given.

Driver board, Moter board, Address sensor board

Chassis section

Case (Side-R, Side-L, Top)

CD door

Front panel section

CD mechanism deck
(CDM58B)

Key board

Panel board

Tape mechanism deck

Sub trans board, Video out board, Back panel, Power transformer
                                                                                   (Trans board)

Main board, Power amp board

Video board, Base unit, BD board

Set

Case (Side-R)

Case (Side-L)

5

qd

qs

qs

q;

Case (Top)

6

Two screws (Case 3 TP2)

8

Screw

     (+BVTP 3

 

×

 10)

3

Screw

     (+BVTP 3

 

×

 10)

9

Screw

     (+BVTT 3

 

×

 8)

4

Screw

     (+BVTT 3

 

×

 8)

1

Two screws

     (Case 3 TP2)

qa

Two screws (+BVTP 3

 

×

 12)

7

Screw (Case 3 TP2)

2

Screw (Case 3 TP2)

8

2

 Pull-out the disc tray.

1

 Turn the pulley to the direction of arrow.

pulley

CD door

Front panel side

CD mechanism deck (CDM58B)

3

qg

qf

7

CD mechanism deck (CDM58B)

Front panel section

qs

Connector (B Deck)

qa

Connector (A Deck)

9

Connector

      (CN714) 

4

Screw

         (+BVTP3X10)

8

Wire (flat type)(CN2)

1

Wire (flat type)

      (CN102)

2

Connector 

      (CN701)

3

Connector

      (CN301) 

qd

Three screws (+BVTP 3

 

× 

6)

q;

Screw 

     (+BVTP 3

 

× 

10)

5

Screw

      (+BVTP 3

 

×

 10)

6

Screw (+BVTP 3

 

×

 10)

Chassis section

9

1

Six screws

     (+BVTP 2.6

 

×

 8)

2

Tape mechanism deck

1

Volume knob

2

Vol knob ring

4

Connector 

      (CN712)

Note: When attching the panel board,
          refer to "Service Note" on page 4. 

6

Panel board

3

5

Cut the seven melted-connection points with a cutting plier.

10

Note: When attching the Key board,
          refer to "Service Note" on page 4. 

2

Key board

1

Cut the six melted-connection points with a cutting plier.

qf

Two screws

     (+BVTT 4

 

×

 6)

qa

Five screws

     (+BVTP 3

 

×

 10)

q;

Two screws

     (+BVTT 3

 

×

 6)

qs

1

Two screws

     (+BVTP 3

 

×

 10)

8

Screw (+BVTP 3

 

×

 10)

Back panel

qg

Two screws

     (+BVTT 4

 

×

 6)

qh

Power transformer

     (T911)

qd

Connector (CN915)

3

Connector (CN2) 

5

Connector

     (CN903)

4

Connector

     (CN901)

2

Cover (Duct)

9

Video out board

7

Sub trans

      board

Trans board

6

Two screws

     (+BVTP 3

 

×

 10)