DOWNLOAD Sony HCD-VR90AV Service Manual ↓ Size: 10.29 MB | Pages: 96 in PDF or view online for FREE

9

5

 Cassette lid (B) assembly

     (Refer to upper figure)

7

 Holder (B) assembly

    (Refer to lower figure)

6

 Holder (A) assembly

    (Refer to lower figure)

4

 Cassette lid (A) assembly

     (Refer to upper figure)

Cassette lid assembly

Holder assembly

Claw

Claw

Claw

Claw

8

 Torsion spring (TC-A)

9

 Torsion spring (TC-B)

1

 Three screws (BVTP 2.6x8)

2

 Three screws

(BVTP 2.6x8)

3

 Tape mechanism

Portion 

B

Portion 

B

Portion 

A

Portion 

A

1

 

Five screws (BVTP3x8)

2

 

CD mechanism 

     deck

3

 

Base unit

1

 

Yoke fitting

2

 

Boss

10

When the disc table is installed, adjust the positions of
roller cam and mark 

” as shown in the figure, then set to

the groove of disc table.

A

A

2

 

Screw (BVTP3X8)

1

 

Screw (BVTP3X8)

4

 

Stop screw

5

 

Disc table

3

 

Bracket (BU)

11

This unit is provided with a simple CD-TEXT display function.
The CD-TEXT contents of 20 tracks are displayed on the fluorescent display tube.
Since the function is simple, some special characters may not be displayed, or may be displayed as other characters.

• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the

customer.

Procedure:
1.

Press three buttons  

t/CLOCK SET  ,  ENTER  , and  1/u  simultaneously.

2.

“COLD RESET” is displayed on the fluorescent display tube and reset is executed.

• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1.

Press  

1/u  button to turn the set ON.

2.

Press  LOOP  button and  

1/u  button simultaneously.

3.

Press the  

1/u  button again to turn the set OFF.

4.

A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

• This mode resets the set with the preset data kept stored in the memory.  The hot reset mode functions same as if the power cord is plugged

in and out.

Procedure:
1.

Press three buttons  

t/CLOCK SET  ,  ENTER  , and  DISC 1  simultaneously.

2.

The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1.

Press  

1/u  button to turn the set ON.

2.

Press three buttons  

t/CLOCK SET  ,  ENTER  , and  DISC 5  simultaneously.

3.

The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.

4.

With the CD in stop status, When  

)  button is pressed, the pick-up moves outside. When 0  button is pressed, the pick-up moves

inside.

5.

To exit from this mode, perform as follows:

1) Move the pick-up to the most inside track.
2) Execute MC cold reset. (Press the three buttons  

t/CLOCK SET  ,  ENTER  , and  1/u  button simultaneously.)

Note:
• Always move the pick-up to most inside track when exiting from this mode.  Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1.

Press  

1/u  button to turn the set ON.

2.

Select the function “TUNER”, and press  TUNER/BAND  button to select the BAND “AM”.

3.

Press  

1/u  button to turn the set OFF.

4.

Press  ENTER  and  

1/u  buttons simultaneously, and the display of  fluorescent indicator tube changes to “AM 9k STEP” or “AM 10k

STEP”, and thus the channel step is changed over.

Procedure:
1.

Press three buttons  

t/CLOCK SET  ,  ENTER  , and  DISC 2  simultaneously.

2.

LEDs and fluorescent indicator tube are all turned on.
Press  DISC 2  button, and the key check mode is activated.

3.

In the key check mode, the fluorescent indicator tube displays “K0 V0 J0”.  Each time a button is pressed, “K”value increases. However,
once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating  

= AMS +  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-”

direction.
“V” Value increases like 1, 2, 3 ... if rotating  VOLUME  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.

4.

To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

12

• This mode is used for checking the AMS operations of the tape deck.

JIG
7-819-039-12 Alignment tape, AMS-110A

Procedure:
1.

Press the  

1/u  button to turn the set ON.

2.

Set the tape (AMS-110A).

3.

Press the three buttons  

t/CLOCK SET  ,  ENTER  , and  DISC 3  button simultaneously.

4.

“TEST MODE” is displayed on the fluorescent display tube. At the same time, the VOLUME indicator blinks.

5.

Press the  FUNCTION  button and switch the function to the deck with the tape (AMS-110A).

6.

Press the  CD SYNCHRO  button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.

7.

AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8.
“NG” is displayed at other times, and the deck stops.

8.

AMS starts in the opposite direction. If the AMS count is 2 at shut down again, “OK” is displayed.
“NG” is displayed at other times.

During the aging mode, both the CD player and tape deck are executed together.
• If an error occurs:
Aging stops, and the error state is displayed on the fluorescent display tube.
• If no error occurs:
Aging is repeated.

Procedure:
1.

Press the  

1/u  button to turn the set ON.

2.

Load 10 minute tapes with unbent rec-proof tabs in decks A and B.

3.

Set CDs on the DISC 1 and DISC 4 tables.

4.

Set the CD mode REPEAT to OFF and PLAY MODE to ALL DISCS.
(Press the  PLAY MODE  and  REPEAT  buttons to set these modes.)

5.

Press the  FUNCTION  button to switch the function to “CD”.

6.

Press the three buttons   

t/CLOCK SET  ,  ENTER  , and  DISC 4  button simultaneously.

7.

Aging starts.

8.

To end aging, press the  

1/u  button to turn the set OFF.

Aging Sequence:
Aging is performed in the following sequence.

• Tape Deck
1.

The tape in deck A is rewound. “TAPE A AG-1” is displayed.

2.

The FWD side of deck A is played for two minutes.
“TAPE A AG-2” is displayed.

3.

The tape in deck A is fast forwarded. “TAPE A AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

4.

The RVS side of deck A is played for two minutes.
“TAPE A AG-4” is displayed.

5.

The tape in deck A is rewound. “TAPE A AG-5” is displayed.

6.

The FWD side of deck B is played for two minutes.
“TAPE B AG-2” is displayed.

7.

The tape in deck B is fast forwarded. “TAPE B AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

8.

The RVS side of deck B is played for two minutes.
“TAPE B AG-4” is displayed.

9.

The tape in deck A is rewound. “TAPE A AG-5” is displayed.

10. Repeated from step 2.