DOWNLOAD Sony HCD-VP700 Service Manual ↓ Size: 10.21 MB | Pages: 90 in PDF or view online for FREE

Model
HCD-VP700
Pages
90
Size
10.21 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
hcd-vp700.pdf
Date

Sony HCD-VP700 Service Manual ▷ View online

11
HCD-VP700
2-11. VIDEO BOARD, DRIVER BOARD, MOTOR BOARD, CD SENSOR BOARD
2-10. LEAF SW BOARD, HEAD (A) BOARD, HEAD (B) BOARD (TCM-230AWR41/MWR41)
4
screw (+PTT 2
 
×
 4), 
    ground point
4
screw (+PTT 2
 
×
 4), 
    ground point
2
LEAF SW board 
1
five claws
5
HEAD (A) board
6
HEAD (B) board
3
remove the four solderings.
Note: This illustration is for TCM-230MWR, but in case of TCM-230AWR, you can remove them in the same way.
9
 Pull-out the Table.
4
Two
 screws (+BVTP 2.6 
×
 8)
q;
Screw (+PTPWH 2.6
 
×
 8)
qa
Tray
1
Screw (+BVTP 2.6
 
×
 8)
qs
Screw (+BVTP 2.6
 
×
 8)
6
Flat type wire (CN721)
3
Flat type wire 
    (CN702)
8
MOTOR board
qd
CD SENSOR board
qf
Flat type wire (CN502)
qg
Flat type wire (CN501)
qh
Two Screws
     (+BVTP 2.6
 
×
 8)
qj
VIDEO board
2
DRIVER board
5
Remove the two solderings of motor.
7
Connector (CN722)
12
HCD-VP700
2-12. BASE UNIT, BD BOARD
4
 Turn the pulley to the direction of arrow.
pulley
Base unit
qg
qd
Two screws (+PTPWH M2.6)
5
Screw (+PTPWH M2.6)
1
Pulley(B)(BU-30), chucking
2
Two Screws (+PTPWH M2.6)
3
Lever (lifter)
qf
Screw (DIA. 12)
qa
Two screws (+BVTP 2.6
 
×
 8)
q;
BD board
qh
Two insulators
6
Holder assy
qh
Two insulators
qs
Two stoppers
7
Flat type wire (CN101)
8
Flat type wire (CN102)
9
Remove the solder
      (four portions).
Spring (insulator), coil
Spring (insulator),
coil
Spring
(insulator),
coil
13
HCD-VP700
SECTION 3
TEST MODE
[Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Press three buttons  x  ,  DISPLAY  , and  DISC 1
simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[Tuner Step Change] (Except for European and Middle Eastern
models)
• A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press  `/1  button to turn the set ON.
2. Select the function “TUNER”, and press  TUNER/BAND  button
to select the BAND “AM”.
3. Press   `/1  button to turn the set OFF.
4. Press  ENTER  and   `/1  buttons simultaneously, and the
display of fluorescent indicator tube changes to “AM 9 k ST”
or “AM 10 k ST”, and thus the channel step is changed over.
[GC Test  Mode]
• This mode is used to check the software version, FL tube, LED,
keyboard and VACS.
Procedure:
1. Press three buttons   x  ,  DISPLAY , and  DISC 2
simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3. When you want to enter the software version display mode,
press  DISC 1 .The model number and destination are displayed.
4. Each time  DISC 1  is pressed, the display changes stating from
MC version, GC version, CD version, CDD, CDM version BD,
ST version, TA version, TM version, TC version, in this order,
and returns to the model number and destination display.
5. When  DISC 3  is pressed while the version numbers are being
displayed except model number and destination, year, month
and day of the software creation appear. When  DISC 3  is pressed
again, the display returns to the software version display. When
DISC 1  is pressed while year, month and day of the software
creation are being displayed, the year, month and day of creation
of the software versions are displayed in the same order of
version display.
6. Press  DISC 2  button, and the key check mode is activated.
7. In the key check mode, the fluorescent indicator tube displays
“KOJOVO”. Each time a button is pressed, “KEY” value
increases.
However, once a button is pressed, _it is no longer taken into
account.
“VOL” value increases like 1, 2, 3...if rotating VOLUME knob
in “+” direction, or it decreases like 0, 9, 8...if rotating in
“_”direction.
8. Also when  DISC 3  is pressed after lighting of all LEDs and FL
tubes, value of VACS appears.
9. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
[MC Test  Mode]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
Procedure:
• To enter MC Test Mode
1. Press the  `/1  button to turn on the set.
2. Press the three buttons of  x   ,  DISPLAY  and  DISC 3
simultaneously.
3. Cursor segment flash on the FL display tube. The input
FUNCTION is changed to GAME.
* Check of Amplifier
Initial settings: Input
, GAME
EQ
, FLAT
Mode
, MUSIC
VA CS
, OFF
Output channel switching:
MUSIC key: L
,  L
, R through
MOVIE key: L
, SL
, SR through
GAME key:L
, L, SL, C R , R, SR, SW through
TOOL MODE key: L 
,  C
, SW through
1. When the  VOLUME  control knob is turned clockwise even
slightly, the sound volume increases to is maximum and a
message “VOLUME MAX” appears for two seconds, then the
display returns to the original display.
2. When the  VOLUME  control knob is tuned counter-clockwise
even slightly, the sound volume decreases to its minimum and a
message “VOLUME MIN” appears for two seconds, then the
display returns to the original display.
* Tuner function
1. In the test mode, the default-preset channel is called even when
the TUNER is selected and an attempt is made to call the preset
channel that has been stored in memory. (It means that the
memory is cleared.)
2. The minimum, center and maximum frequency of each band is
set then.
* Tape recording test
1. To enter the MC Test Mode.
2. Load tapes in both tape decks A and B.
3. Press the REC button to start recording.
4. Pressing the  M  ,  m  buttons during recording returns the
tape to the recording start position and stops it at this position.
5. Pressing the “High Speed Dubbing” key while playing back the
tape of deck B switches the playback speed between “Normal
Speed” and “High Speed”.
Note:
When the playback direction of the tape is set to other than “ONY
WAY”, the restriction on the number of times playback which can
be repeated will be cleared.
* AMS Test Mode
1. Set TAPE function
2. Select the desired loop by pressing the  PLAY MODE  button.
Insert a test tape AMS-110A or AMS-120 to Deck A.
3. Press the  SPECTRUM  or  KARAOKE PON  button to enter
the AMS test mode.
4. After a tape is rewound first, the FF AMS is checked, and the
mechanism is shut off after detecting the AMS signal the AMS
signal twice.
5. Then the REW AMS is checked and the mechanism is shut off
after detecting the AMS signal twice.
6. When the check is complete, a message of either OK or NG
appears.
* To return to normal mode again.
1. When you want to exit this mode, press the  `/1  button.
2. The cold reset is enforced at the same time.
14
HCD-VP700
[CD Ship Mode (No Memory Clear)]
• This mode moves the position to the position durable to vibra-
tion Use this mode when returning the set to the customer after
repair.
Procedure:
1. Press  `/1  button to turn the set ON.
2. Press three  ENTER  ,  DISK 1  button and CD  button
simultaneously.
3. After the “STANBY” display blinks six times, a message
“LOCK” is displayed on the fluorescent indicator rube, and the
CD ship mode is set.
[CD Ship Mode (Memory Clear)]
• This mode moves the pickup to the position durable to vibra-
tion. Use this mode when returning the set to the customer after
repair.
Procedure:
1. Press  `/1  button to turn the set ON.
2. Press three buttons  CD  and  `/1  button simultaneously.
3. After the “STANDBY” display blinks six times, a message
“LOCK” is displayed on the fluorescent indicator tube, and the
CD ship mode is set.
[CD Service Mode]
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Press  `/1  button to turn the set ON.
2. Select the function “CD”.
3. Press three buttons  ENTER  ,  DISC 1  , and  x   simultaneously.
4. The CD service mode is selected.
5. With the CD in stop status, press  M  button to move the
pickup to outside track, or press  m  button to inside track.
6. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press  `/1  button to turn the set OFF.
Note:
• Always move the pickup to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.
Page of 90
Display

Click on the first or last page to see other HCD-VP700 service manuals if exist.