Sony HCD-RV600D / HCD-RV600DJ / MHC-RV600D / MHC-RV600DJ Service Manual ▷ View online
13
HCD-RV600D/RV600DJ
1
flat type wire (CN501,CN202)
6
flat type wire (CN501)
2
flat type wire
(CN503,CN302)
7
two
screws
(BVTP 3
×
8)
qd
screw
(BVTP 3
×
8)
9
screw
(BVTT 3
×
6)
qf
screw
(BVTP 3
×
8)
3
two
screws
(BVTP 3
×
8)
4
PWB holder
5
VIDEO board
qa
qs
heat sink (DVD)
qg
MB board
8
bracket (AL)
0
two
screws
(BVTP 3
×
8)
4
flat type wire
6
cushion (DVD)
7
cushion (DVD)
5
connector
1
screw
(BVTP 3
×
8)
3
8
bracket (DVD)
2
cushion (A)
qs
RF board
9
0
qa
two
screws (PTP 2.6
×
12)
qd
screw (BVTP 2.6
×
8)
qf
DRIVER board
2-11. VIDEO Board, MB Board
2-12. RF Board, DRIVER Board
Ver 1.1 2002.11
14
HCD-RV600D/RV600DJ
7
insulator
2
8
insulator
6
insulator
0
holder (DBU1) assy
4
step
screw (L)
5
step
screw (L)
1
floating
screw (PTPWH M2.6)
3
step
screw (L)
9
optical pick-up
qs
tray (DVD)
qa
screw (PTPWH 2.6
×
8)
1
two
screws (BVTP 2.6
×
8)
9
screw (BVTP 2.6
×
8)
7
screw (BVTP 2.6
×
8)
qd
screw (BVTP 2.6
×
8)
5
connector (CN723)
4
connector (CN722)
3
flat type wire (CN721)
6
MOTOR board
qf
SENSOR board
8
DIODE board
0
bracket (sensor)
2
Remove the two solderings of motor.
2-13. Optical Pick-up
2-14. MOTOR Board, DIODE Board, SENSOR Board
15
HCD-RV600D/RV600DJ
[Cold Reset]
• The cold reset clears all data including preset data stored in the
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure:
1. Press three buttons x , ENTER , and ?/1 simultaneously.
2. The fluorescent indicator tube display “COLD RESET” and
1. Press three buttons x , ENTER , and ?/1 simultaneously.
2. The fluorescent indicator tube display “COLD RESET” and
the set is reset.
[Hot Reset]
1. Press three buttons x , GAME EQ , and DISPLAY simulta-
1. Press three buttons x , GAME EQ , and DISPLAY simulta-
neously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset
[Tuner Step Change] (Except for European and Middle Eastern
models)
• A step of AM channels can be changed over between 9 kHz and
models)
• A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press `/1 button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND button
1. Press `/1 button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND button
to select the BAND “AM”.
3. Press `/1 button to turn the set OFF.
4. Press ENTER and `/1 buttons simultaneously, and the display
4. Press ENTER and `/1 buttons simultaneously, and the display
of fluorescent indicator tube changes to “AM 9 k STEP” or
“AM 10 k STEP”, and thus the channel step is changed over.
“AM 10 k STEP”, and thus the channel step is changed over.
[VIDEO/MD Function Change]
• Change of function VIDEO or MD ( also the input level changes).
Procedure:
1. Press `/1 button to turn the set ON.
2. Press VIDEO (MD) and `/1 buttons simultaneously, and the
• Change of function VIDEO or MD ( also the input level changes).
Procedure:
1. Press `/1 button to turn the set ON.
2. Press VIDEO (MD) and `/1 buttons simultaneously, and the
display of fluorescent indicator tube changes to “MD” or
“VIDEO”, and thus the channel step is changed over.
“VIDEO”, and thus the channel step is changed over.
3. Press `/1 button to turn the set OFF.
[DISC TRAY LOCK]
The disc tray lock function for the antitheft of a demonstration disc
in the store is equipped.
The disc tray lock function for the antitheft of a demonstration disc
in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the set on.
2. Press two buttons of x and Z simultaneously for five seconds.
3. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press two buttons of x and Z simultaneously for five seconds.
2. The message “UNLOCKED” is displayed and the tray is
1. Press the ?/1 button to turn the set on.
2. Press two buttons of x and Z simultaneously for five seconds.
3. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press two buttons of x and Z simultaneously for five seconds.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note : When “LOCKED” is displayed, the tray lock is not released
by turning power on/off with the POWER button.
SECTION 3
TEST MODE
5. When the Key count check mode is entered, the display shows
the indication of “KEY 0 1”.
Whenever the button is pressed, number in the first digit
increments. (RV90D: 38) At the same time, only when the key
is being pressed, the KEY channel is displayed in the second
digit. (KEY0: 1, KEY1: 2, KEY2: 3)
(The buttons that are already pressed once and the buttons of
?/1 and DISPLAY are not counted.)
Whenever the button is pressed, number in the first digit
increments. (RV90D: 38) At the same time, only when the key
is being pressed, the KEY channel is displayed in the second
digit. (KEY0: 1, KEY1: 2, KEY2: 3)
(The buttons that are already pressed once and the buttons of
?/1 and DISPLAY are not counted.)
6. When the Headphones input check mode is entered, the display
shows the indication of “H_P OFF” or “H_P ON” depending
on the PHONES jack status.
on the PHONES jack status.
7. When the Volume check mode is entered, the display shows the
indication of “VOLUME FLAT” or “VOLUME DOWN” or
“VOLUME UP” depending on the VOLUME status.
“VOLUME UP” depending on the VOLUME status.
8. You can exit the Test Mode when you press the GAME EQ
and DISC 2 buttons simultaneously.
[GC Test Mode]
• This mode is used to check the FL tube, LED, keyboard, vol-
• This mode is used to check the FL tube, LED, keyboard, vol-
ume and phones.
Procedure:
1. Press three buttons x , GAME EQ , and DISC 2 simulta-
1. Press three buttons x , GAME EQ , and DISC 2 simulta-
neously.
2. LEDs and fluorescent indicator tube are all turned on.
3. Press simultaneously the two buttons of GAME EQ and DISC
3. Press simultaneously the two buttons of GAME EQ and DISC
2 . Whenever these two buttons are pressed simultaneously, the
mode changes from Key check, Key count check, Headphones
input check and Volume check in this order.
mode changes from Key check, Key count check, Headphones
input check and Volume check in this order.
4. When the Key check mode is entered, the display shows the
indication of “KEY 0 0 0”.
The keys that are assigned to the respective channels of the key
entry signal lines (KEY0, KEY1, KEY2) that are input to IC001
Display Controller on the panel board, are checked. While you
press the button, the number that corresponds to the key shown
in the table below, is displayed in the location of the
corresponding channel. (The ?/1 and DISPLAY buttons are
not included in these channels.)
The keys that are assigned to the respective channels of the key
entry signal lines (KEY0, KEY1, KEY2) that are input to IC001
Display Controller on the panel board, are checked. While you
press the button, the number that corresponds to the key shown
in the table below, is displayed in the location of the
corresponding channel. (The ?/1 and DISPLAY buttons are
not included in these channels.)
Display
Left
Center
Right
(KEY0)
(KEY1)
(KEY2)
1
DVD
X
DISC 1
2
TUNER/BAND
x
DISC 2
3
TAPE A/B
ALBUM +
DISC 3
4
VIDEO (MD)
>
Z OPEN/CLOSE
5
GAME
M +
DISC SKIP/
EX-CHANGE
6
—
g G
TUNER MEMORY
PLAY MODE
7
DVD MENU
– m
FM MODE
REPEAT
8
GAME EQ
ALBUM –
DIRECTION
DVD TOP MENU
9
MUSIC EQ
.
CD SYNC
10
EFFECT ON/OFF
b
REC
PAUSE/START
11
GAME MIXING
V
P FILE
12
GROOVE
B
ENTER
13
—
v
MOVIE EQ
14
—
—
DVD DISPLAY
Ver 1.1 2002.11
16
HCD-RV600D/RV600DJ
[MC Test Mode]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
Procedure:
• To enter MC Test Mode
1. Press `/1 button to turn on the set.
2. Press the three buttons of x , GAME EQ and DISC 3 simul-
• To enter MC Test Mode
1. Press `/1 button to turn on the set.
2. Press the three buttons of x , GAME EQ and DISC 3 simul-
taneously.
* Check of Amplifier
Initial settings: Input
, GAME
EQ
, FLAT
Mode , MUSIC
VA CS , OFF
VA CS , OFF
Output channel switching:
MUSIC key: L
, L
R , R through
MOVIE key: L
, SL
R , SR through
GAME key:L
, L, SL, C R , R, SR, SW through
TOOL MODE key: L , C
R , SW through
1. When VOLUME control knob is turned clockwise even
slightly, the sound volume increases to is maximum and a
message “VOLUME MAX” appears for two seconds, then the
display returns to the original display.
message “VOLUME MAX” appears for two seconds, then the
display returns to the original display.
2. When VOLUME control knob is tuned counter-clockwise
even slightly, the sound volume decreases to its minimum and a
message “VOLUME MIN” appears for two seconds, then the
display returns to the original display.
message “VOLUME MIN” appears for two seconds, then the
display returns to the original display.
3. When you press the v button, the message “GEQ MAX” is
displayed and the entire band of the graphic equalizer is set to
the maximum level.
the maximum level.
4. When you press the V button, the message “GEQ MIN” is
displayed and the entire band of the graphic equalizer is set to
the minimum level.
the minimum level.
5. When you press the b , B or P FILE button, the message
“GEQ FLT” is displayed and the entire band of the graphic
equalizer is set to the center level.
equalizer is set to the center level.
6. Whenever you press the ENTER button, it toggles between
“VACS ON” and “VAC OFF” so that you can switch ON or
OFF of VACS.
OFF of VACS.
* To return to normal mode again.
1. When you want to exit this mode, press `/1 button.
2. The cold reset is enforced at the same time.
1. When you want to exit this mode, press `/1 button.
2. The cold reset is enforced at the same time.
[Aging Mode]
This mode can for operation check of tape deck section.
• If an error occurred:
The aging operation stops and display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1. Press the DVD button to select the function “DVD”.
2. Load the tapes into the decks A and B respectively.
3. Set a disk in “DISK1” tray.
4. Press the PLAY MODE button to set the “ALL DISCS” mode,
• If an error occurred:
The aging operation stops and display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1. Press the DVD button to select the function “DVD”.
2. Load the tapes into the decks A and B respectively.
3. Set a disk in “DISK1” tray.
4. Press the PLAY MODE button to set the “ALL DISCS” mode,
and press the REPEAT button to “REPEAT” off.
5. Press three buttons of x , GAME EQ , and DISC SKIP/EX-
CHANGE simultaneously.
6. The florescent indicator tube display “AGING”, aging mode
start.
7. To exit from the aging mode, operate the cold reset.
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
• If an error occurred, stop display that step.
Aging mode sequence (Tape deck section):
Rewind the tape A
“TAPE A AG-1”
Rewind the tape B
“TAPE A AG-2”
FWD play the tape A
“TAPE A AG-3”
Fast forward the tape A
“TAPE A AG-4”
RVS play the tape A
“TAPE A AG-5”
Rewind the tape A
“TAPE A AG-6”
FWD play the tape B
“TAPE B AG-3”
Fast forward the tape B
“TAPE B AG-4”
RVS play the tape B
“TAPE B AG-5”
Rewind the tape B
“TAPE B AG-6”
Shut off
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
Click on the first or last page to see other HCD-RV600D / HCD-RV600DJ / MHC-RV600D / MHC-RV600DJ service manuals if exist.