DOWNLOAD Sony HCD-RG66 / MHC-RG66 Service Manual ↓ Size: 4.9 MB | Pages: 58 in PDF or view online for FREE

11

1

×

2

×

3

4

four screws (+BTTP M2.6 )

5

2

wire (flat type)

      16p (CN731)

8

wire (flat type)

      8p (CN702)

9

DRIVER board

6

BD board

7

screw (+BTTP M2.6

 )

1

connector 10p (CN735)

3

connector

      6p (CN732)

12

1

2

3

qs

optical pick-up

     (KSM-213D)

qa

8

two screws (+PTPWH M2.6)

9

two spring (insulator), coils

2

CD (cover) (down)

7

two spring (insulator), coils

3

screw (+PTPWH M2.6)

q;

screw (DIA. 12)

5

two screws (+BTTP M2.6)

1

screw (+BTTP M2.6)

qf

two insulators

4

holder (BU) assy

qd

two insulators

6

two stoppers (BU)

13

2

 Pull out the disc tray.

6

two

 screws (+BTTP M2.6)

3

screw (+PTPWH 2.6

 

×

 8)

4

tray

9

screw (+BTTP M2.6)

8

MOTOR board

q;

ADDRESS SENSOR board

7

Remove the two solderings of motor.

5

connector 4p (CN722)

1

 Turn the pulley to the direction of arrow.

pulley

Front panel side

CD mechanism deck (CDM58F-K6A)

7

6

5

4

2

3

1

14

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning
the set to the customer.

Procedure:
1. Press three buttons x  ,  ENTER  ,  and ?/1 simultaneously.
2. The fluorescent indicator tube displays “COLD RESET” and

the set is reset.

This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:

The aging operation stops and is displayed status.

• If no error occurs:

The aging operation continues repeatedly.

1.

Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set three discs in tray.  Select ALL DISCS, and REPEAT OFF.
2) Load the tapes recording use into both decks.
3) Press three buttons x ,  GAME EQ ,  and

DISC SKIP/EX-CHANGE  simultaneously.

4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [Cold Reset].

2.

Aging mode in CD section

1) Operation during aging mode
• In the agining mode ,the program is excuted in the following

sequence.

(1) The disc tray opens and closes.
(2) The disc tray turns to select a disc 3.
(3) The pick-up accesses to the first track, and plays 3 seconds.
(4) The pick-up accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display

“AGING 

∗∗∗∗

” value increases.

(10) If no error occurs, the aging operation continues repeatedly.

2) Error display

Step

1

2

3

4

5

6

7

Operation

Rewind the TAPE A

Rewind the TAPE B

Play the TAPE A (1 minute)

Stop the TAPE A (1 second)

Play the TAPE A (3 minutes)

Rewind(AMS) the TAPE A

F.F.(AMS) the TAPE A

Display

TAPE

AAG-01

TAPE

BAG-01

TAPE

AAG-02

TAPE

AAG-03

TAPE

AAG-04

TAPE

AAG-05

TAPE

AAG-06

Disc error

Display

Error

E00D01022

Focus error (No disc)

E00D02022

Sub Q error (Focus is good)

E00D02023

TOC reading error

E00D02014

Access error (Unable within regular time)

Mechanism error

Display

Error

E00M__E_0

Error during opening tray

E00M__C_2

EX-CHANGE disc error

E00M__D_0

Error during closing tray

E00M__F_3

EX-OPEN error

E00M__D_5

EX-CLOSE error

E00M__C_2

Chuck-up error

E00M__C_3

Unchucking error

3.

Aging mode in Tape Deck section

1) Operation during aging mode
• In the agining mode, the program is excuted in the following

sequence.

2) Error display
• If error occurred, the display remains like “TAPE BAG-2”.

4.

Exiting from the aging mode

• Be sure to perform Cold Reset to exit from the aging mode.

• All fluorescent segments and LEDs are tested.
• Keyboard check.

Procedure:
1. Press the  ?/1  button to turn the set ON.
2. To enter the test mode, press the three buttons  x ,  GAME EQ

and  DISC 2  simultaneously.

3. All segments and LEDs are turned on.
4. Press the  GAME EQ  and  DISC 2  buttons simultaneously, and

the key check mode is activated.

5. The message “KEY 0 0 0 ” is displayed.

Each time a button is pressed, the key code number is displayed.

6. Press the  GAME EQ  and  DISC 2  buttons simultaneously, and

the key count mode is activated.

7. The message “KEYCNT 0 1” is displayed.

Each time a button is pressed, “KEYCNT 0 1” value increased.
However, once a button is pressed, it is no longer taken into
account.

8. Press the  GAME EQ  and  DISC 2  buttons simultaneously, and

the head phone detect mode is activated.

9. The message “H_P OFF” is displayed when a headphone jack

is not inserted.
“H_P ON ” is displayed when a headphone jack is inserted.

10. Press the  GAME EQ  and  DISC 2  buttons simultaneously, and

the volume control detect mode is activated.

11. The message “VOLUME FLAT” is displayed.

“VOLUME UP” is displayed if rotating VOLUME knob
clockwise, or “VOLUME DOWN” is displayed if rotating
counterclockwise.

12. To exit from the GC test mode after the volume control detect

mode, press the  GAME EQ  and  DISC 2  buttons simultaneously.