DOWNLOAD Sony HCD-RG550 / HCD-RG660 / MHC-RG550 / MHC-RG660 Service Manual ↓ Size: 5.12 MB | Pages: 75 in PDF or view online for FREE

29

29

• X

: parts extracted from the component side.

• Y

: parts extracted from the conductor side.

•

: Pattern from the side which enables seeing.

(The other layer’s patterns are not indicated.)

Caution:
Pattern face side:

Parts on the pattern face side seen from

(Conductor Side)

the pattern face are indicated.

Parts face side:

Parts on the parts face side seen from

(Component Side)

the parts face are indicated.

C

B

These are omitted.

E

Q

B

These are omitted.

C

E

Q

B

These are omitted.

C

E

Q

Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted.  pF: µµF

50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in 

Ω

 and 

1

/

4

 

W or less unless otherwise

specified.

•

2

: nonflammable resistor.

•

C

: panel designation.

•

Indication of transistor.

•

A

: B+ Line.

•

B

: B– Line.

• Voltage and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : FM
(

) : CD PLAY

[

] : TAPE PLAY (DECK-A)

{

 } : TAPE PLAY (DECK-B)

〈〈

 

〉〉

: REC

∗

: Impossible to measure

• Voltages are taken with a VOM (Input impedance 10 M

Ω

).

Voltage variations may be noted due to normal produc-
tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-
tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F

: TUNER (FM/AM)

J

: CD PLAY

E

: TAPE PLAY (DECK-A)

d

: TAPE PLAY (DECK-B)

G

: REC

j

: MD (VIDEO) IN

N

: MIC INPUT

• Abbreviation

E2

: 120 V AC area in E model

E3

: 240 V AC area in E model

E51

: 220 V AC area in E model

MX

: Mexican model

Note: The components identified by mark 

0

 or dotted line

with mark 

0

 are critical for safety.

Replace only with part number specified.

Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.

30

30

(Page 38)

C860

R860

FB803

FB805

FB804

FB806

R806
R807

R747

C761

R761

R762

R746

BD BOARD

(SIDE A)

1-688-077-

(11)

11

OPTICAL

PICK-UP

BLOCK

(KSS-213D)

IC803

BD BOARD

(SIDE B)

1-688-077-

(11)

11

M702

(SPINDLE)

M

+

–

M701

(SLED)

M

+

–

S701

(LIMIT IN)

TP

(RF)

TP

(FE)

TP

(TE)

TP

(VC)

E

B

C

7

1

14

8

22

28

15

21

Ref. No.

Location

IC721

E-8

IC722

C-9

IC801

E-3

IC802

F-3

IC803

F-9

Q701

B-7

31

31

(Page 36)

32

32

(Page 38)

Ref. No.

Location

D701

D-6

D711

D-7

IC701

F-6

IC712

F-7

IC731

E-11

Q731

C-9