DOWNLOAD Sony HCD-RG30 / MHC-DX20 / MHC-RG30 Service Manual ↓ Size: 5.81 MB | Pages: 59 in PDF or view online for FREE

15

[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:

The aging operation stops and display status.

• If no error occurs:

The aging operation continues repeatedly.

1.

Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray.  Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x ,  ENTER ,  and

DISC SKIP EX-CHANGE  simultaneously.

4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [MC Cold Reset].

3. Aging Mode in CD section
1) Display state
• No error occurs

Note:
[*][*][*][*] :  Number of aging operations

E

** s ## $$ %%
1 2 3 4 5

• When the buttons  x ,  ENTER  and  DISC 1  are pressed simultaneously, number of time of the mechanism error and the NO DISC error

can be checked.
Display:

EMC**EDC**

**:

Number of times of error (Maximum three times)

EMC: Mechanism error
EDC: NO DISC error

• When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.

D: No disc error

01: FOCUS ERROR
02: GFS ERROR
03: SETUP ERROR

01: NO DISC judgment without chucking retry
02: NO DISC judgment after chucking retry

Status at the time of NO DISC judgment
(High order digits only)
1:

STOP

2:

SETUP

3:

TOC READ

4:

ACCESS

5:

PLAY BACK

6:

PAUSE

7:

MANUAL SEARCH (PLAY)

8:

MANUAL SEARCH (PAUSE)

AGING[*][*][*][*]

1

 

**

2

 s

3

 

##

4

 

$$

5

 

%%

M: Mechanism error

Don’t care

High order digits only
D: Stopped during closing due to problems other than mechanism.
E: Stopped during opening due to problems other than mechanism.
C: Stopped during chucking due to problems other than mechanism.
F: Stopped during EX-opening due to problems other than mechanism.

Emergency related errors (High order digits only)
1:

Stopped during chuck-up

2:

Stopped during chuck-down

3:

Time out by EX-OPEN

5:

Time out by EX-CLOSE

The error No. 00 indicates the newest error.  As the error No. increases, it means the older error.
When you want to retrieve the error history, press the  PLAY MODE  button in the case of mechanism error.
Or press the  REPEAT  button in the case of NO DISC error.

Display

16

2)  Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1)

The disc tray opens and closes.

(2)

The mechanism accesses DISC 2 and makes an attempt to
read TOC.  However, since there are no discs, a message
“CD2 NO DISC” appears.

(3)

The mechanism accesses DISC 3 and a message “CD3 NO
DISC” appears.

(4)

The disc tray turns to select a disc1.

(5)

A disc is chucked.

(6)

TOC of disc is read.

(7)

The pickup accesses to the track 1, and  playing 2 seconds.

(8)

The pickup accesses to the last track, and playing 2 seconds.

(9)

Every time when an aging operation of step 1 to step 8 is
complete, the display “AGING[*][*][*][*]” value increases
as the number of aging operations is counted up.

(10) Returns to step 1.

3. Aging Mode in Tape Deck section
1) Display state
• No error occurs

Display action now

• Error occurred

Display action last time

2)  Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1) Rewind is executed up to the top of tape A and B.
(2) A tape on FWD side is played for 2 minutes.
(3) FF is executed up to either made for 20 second or the end of

tape.

(4) B tape is reversed, and the tape on REV side is played for 2

minutes.

(5) Rewind is executed up to the top of tape.
(6) Returns to step 2, and repeat steps from 2 to 5.

[Function Change Mode]
* elect either VIDEO or MD of the external FUNCTION input.

Procedure:
1.

Turn on the power.

2.

Press the two buttons  MD (VIDEO)  and  ?/1  at the same
time.
The main power is turned on and the other function of the
previous function is selected and displayed.  “MD” or
“VIDEO”.

NO. Display action

Action contents

Final timing

1

TAPE A AG-6

Rewind the TAPE A

The top of tape

TAPE B AG-1

Rewind the TAPE B

2

TAPE A AG-2

FWD play the TAPE A

2 minutes playing

3

TAPE A AG-3

F.F. the TAPE A

20 second FF or the end
of tape

4

TAPE A AG-4

REV play the TAPE A

2 minutes playing

5

TAPE A AG-5

Rewind the TAPE A

The top of tape

6

TAPE B AG-2

FWD play the TAPE B

2 minutes playing

7

TAPE B AG-3

F.F. the TAPE B

20 second FF or the end
of tape

8

TAPE B AG-4

REV play the TAPE B

2 minutes playing

9

TAPE B AG-5

Rewind the TAPE B

The top of tape

17

Procedure:
1.

Supply a 98 MHz signal at 28 dB from the ANTENNA terminal.

2.

Tune the set to 98 MHz.

3.

Adjust RV101 to the point (moment) when the TUNED
indicator will change from going off to going on.

Adjustment Location: MAIN board

Procedure:
1.

Supply a 98 MHz signal at 60 dB from the ANTENNA terminal.

2.

Tune the set to 98 MHz.

3.

Measure voltage between pin 21 and pin 23 of IC 101.  Adjust
T101 ubtil the voltage becomes 0 V.

Adjustment Location: MAIN board

FM RF Signalgenerator

75 

Ω

 coaxial

Carrier frequency : 98 MHz
Modulation           : AUDIO 1 kHz, 75 kHz
                              deviation (100%)
Output level          : 28 dB  (at 75 

Ω

 open)

FM ANTENNA terminal
(TM101)

set

FM RF Signalgenerator

75 

Ω

 coaxial

Carrier frequency : 98 MHz
Modulation           : AUDIO 1 kHz, 75 kHz
                              deviation (100%)
Output level          : 60 dB  (at 75 

Ω

 open)

FM ANTENNA terminal
(TM101)

set

Note :

1. CD Block is basically designed to operate without adjustment.

Therefore, check each item in order given.

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M

Ω impedance.

4. Clean the object lens by an applicator with neutral detergent

when the signal level is low than specified value with the
following checks.

Procedure :
1. Connect oscilloscope to TP (FEO).
2. Connect between TP (FEI) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (D GND) by lead wire.
4. Turn Power switch on.
5. Load a disc (YEDS-18) and actuate the focus search. (In

consequence of open and close the disc tray, actuate the focus
search)

6. Confirm that the oscilloscope waveform (S-curve) is

symmetrical between A and B. And confirm peak to peak level
within 4 

±1 Vp-p.

7. After check, remove the lead wire connected in step 2 and 3.

Note : • Try to measure several times to make sure than the ratio

of A : B or B : A is more than 10 : 7.

• Take sweep time as long as possible and light up the

brightness to obtain best waveform.

Procedure :
1. Connect oscilloscope to TP (RF).
2. Connect between TP (AGCCON) and TP (D GND) by lead wire.
3. Turned Power switch on.
4. Load a disc (YEDS-18) and playback.
5. Confirm that oscilloscope waveform is clear and check RF signal

level is correct or not.

6. After check, remove the lead wire connected in step 2.

±1Vp-p

T101

RV661

RV101

IFT101

T102

RV661:TAPE SPEED

T101:NULL

RV101:FM TUNED LEVEL

18

Note : Clear RF signal waveform means that the shape “ 

◊ ” can be clearly

distinguished at the center of the waveform.

Procedure :
1. Connect oscilloscope to TP (TEO) and TP (VC).
2. Turned Power switch on.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the  gG  button. (Becomes the 1 track jump mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope

waveform.

6. After check, remove the lead wire connected in step 1.

RF PLL Free-run Frequency Check
Procedure :
1. Connect frequency counter to test point (XPCK) with lead wire.

2. Turned Power switch on.
3. Put the disc (YEDS-18) in to play the number five track.

Confirm that reading on frequency counter is 4.3218MHz.

± 0.3Vp-p

±0.6Vp-p

Specified level: –– 

× 100=less than ±22%

B

A

TP

(XPCK)

TP

(TEO)

TP

(FEO)

TP

(FEI)

TP

(RF)

TP

(VC)

TP

(DGND)

TP

(AGCCON)

1

12

24

1

20

21

40

60

80

41

61

IC101

IC103

[BD BOARD] (Conductor Side)