Sony HCD-RG11 / MHC-RG11 Service Manual ▷ View online
7
HCD-RG11
2-4. Tape Mechanism Deck And PANEL Board
2-5. SUB TRANS Board, VIDEO OUT Board and TRANS Board
qa
PANEL board
7
volume knob
2
six
screws
(+BVTP 2.6
×
8)
8
six
screws
(+BVTP 2.6
×
8)
9
five
screws
(+BVTP 2.6
×
8)
q;
eight
screws
(+BVTP 2.6
×
8)
3
tape mechanism deck
6
belt (FR)
4
belt (BF)
5
belt (AF)
1
flat type wire (17 core)
qg
four screws
(+BVTT 4
×
6)
qh
power transformer (T911)
TRANS board
7
cover (duct)
qf
connector (CN915)
4
connector (CN504)
1
connector (CN901)
qa
VIDEO OUT board
2
connector (CN2)
3
connector
(CN903)
qs
five screws
(+BVTP 3
×
10)
qd
back panel
5
two screws
(+BVTP 3
×
10)
8
two screws
(+BVTP 3
×
10)
9
SUB TRANS
board
6
q;
screw
(+BVTP 3
×
10)
8
HCD-RG11
2-6. MAIN Board and POWER Board
2-7. Base Unit
6
three screws (+BVTP 3
×
8)
8
two screws (+BVTP 3
×
8)
9
heat sink
5
two screws (+BVTP 3
×
16)
1
two screws (+BVTP 3
×
10)
4
MAIN board
7
POWER board
MAIN board
2
3
4
Turn the pulley to the direction of arrow.
pulley
Base unit
qs
q;
two screws
(+PTPWH M2.6)
6
screw
(+PTPWH M2.6)
1
pulley (B), chucking
2
two screws (+PTPWH M2.6)
3
lever (lifter)
qa
screw (DIA. 12)
8
two screws (+BVTP 2.6
×
8)
qd
two insulators
7
holder (BU) assy
qd
two insulators
9
two stoppers (BU)
5
flat type wire (16 core)
qf
two spring (insulator), coils
qf
spring (insulator),
coil
spring
(insulator),
coil
(insulator),
coil
9
HCD-RG11
2-8. CD Board, DRIVER Board, MOTOR Board and ADDRESS SENSOR Board
9
Pull-out the Table.
4
two
screws (+BVTP 2.6
×
8)
q;
screw (+PTPWH 2.6
×
8)
qa
tray
1
screw (+BVTP 2.6
×
8)
qs
screw (+BVTP 2.6
×
8)
6
flat type wire (8 core)
3
flat type wire
(8 core)
8
MOTOR board
qd
ADDRESS SENSOR board
qf
flat type wire (16 core)
qh
CD board
2
DRIVER board
5
Remove two solderings of turn motor (M721).
7
connector
qg
four screws
(+BVTP 2.6
×
8)
10
HCD-RG11
SECTION 3
TEST MODE
[Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure:
1. Press three buttons x , DISPLAY , and ?/1 simultaneously.
2. The fluorescent indicator tube displays “COLD RESET” and
1. Press three buttons x , DISPLAY , and ?/1 simultaneously.
2. The fluorescent indicator tube displays “COLD RESET” and
the set is reset.
[Aging Mode]
This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:
deck section.
• If an error occurred:
The aging operation stops and is displayed status.
• If no error occurs:
The aging operation continues repeatedly.
1.
Operating method of Aging Mode
Turn on the main power and select “CD” of the function.
1) Set three discs in tray. Select ALL DISCS, and REPEAT OFF.
2) Load the tapes recording use into both decks.
3) Press three buttons x , DISPLAY , and
1) Set three discs in tray. Select ALL DISCS, and REPEAT OFF.
2) Load the tapes recording use into both decks.
3) Press three buttons x , DISPLAY , and
DISC SKIP EX-CHANGE simultaneously.
4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [Cold Reset].
5) To exit the aging mode, perform [Cold Reset].
2.
Aging mode in CD section
1) Operation during aging mode
• In the agining mode ,the program is excuted in the following
• In the agining mode ,the program is excuted in the following
sequence.
(1) The disc tray opens and closes.
(2) The disc tray turns to select a disc 3.
(3) The pickup accesses to the first track, and plays 3 seconds.
(4) The pickup accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display
(2) The disc tray turns to select a disc 3.
(3) The pickup accesses to the first track, and plays 3 seconds.
(4) The pickup accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display
“AGING
∗∗∗∗
” value increases.
(10) If no error occurs, the aging operation continues repeatedly.
2) Error display
Step
1
2
3
4
5
6
7
8
9
10
11
12
Operation
Rewind the TAPE A
Rewind the TAPE B
Play the TAPE A (1 minute)
Stop the TAPE A (1 second)
Play the TAPE A (3 minutes)
Rewind(AMS) the TAPE A
F.F.(AMS) the TAPE A
Play the TAPE B (1 minute)
Stop the TAPE B (1 second)
Record the TAPE B (3 minutes)
Rewind(AMS) the TAPE B
F.F.(AMS) the TAPE B
Display
TAPE
AAG-1
TAPE
BAG-2
TAPE
AAG-2
TAPE
AAG-3
TAPE
AAG-4
TAPE
AAG-5
TAPE
AAG-6
TAPE
BAG-2
TAPE
BAG-3
TAPE
BAG-4
TAPE
BAG-5
TAPE
BAG-6
Disc error
Display
Error
E00D01022
Focus error (No disc)
E00D02022
Sub Q error (Focus is good)
E00D02023
TOC reading error
E00D02014
Access error (Unable within regular time)
Mechanism error
Display
Error
E00M__E_0
Error during opening tray
E00M__C_2
EX-CHANGE disc error
E00M__D_0
Error during closing tray
E00M__F_3
EX-OPEN error
E00M__D_5
EX-CLOSE error
E00M__C_2
Chuck-up error
E00M__C_3
Unchucking error
3.
Aging mode in Tape Deck section
1) Operation during aging mode
• In the agining mode, the program is excuted in the following
• In the agining mode, the program is excuted in the following
sequence.
2) Error display
• If error occurred, the display remains like “TAPE BAG-2”.
• If error occurred, the display remains like “TAPE BAG-2”.
4.
Exiting from the aging mode
• Be sure to perform Cold Reset to exit from the aging mode.
Click on the first or last page to see other HCD-RG11 / MHC-RG11 service manuals if exist.