Sony HCD-RG11 / MHC-RG11 Service Manual ▷ View online
2
HCD-RG11
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
of emitting radiation exceeding the limit for
Class 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
TABLE OF CONTENTS
1. GENERAL
·········································································· 3
2. DISASSEMBLY
································································ 5
2-1. Case (Top) ····································································· 5
2-2. CD Door ········································································ 6
2-3. Front Panel Section and
2-2. CD Door ········································································ 6
2-3. Front Panel Section and
CD Mechanism Deck (CDM58F-K6) Section ·············· 6
2-4. Tape Mechanism Deck And PANEL Board ·················· 7
2-5. SUB TRANS Board, VIDEO OUT Board and
2-5. SUB TRANS Board, VIDEO OUT Board and
TRANS Board ······························································· 7
2-6. MAIN Board and POWER Board ································· 8
2-7. Base Unit ······································································· 8
2-8. CD Board, DRIVER Board, MOTOR Board and
2-7. Base Unit ······································································· 8
2-8. CD Board, DRIVER Board, MOTOR Board and
ADDRESS SENSOR Board ·········································· 9
3. TEST MODE
···································································· 10
4. ELECTRICAL ADJUSTMENTS
······························· 12
5. DIAGRAMS
······································································ 14
5-1. Circuit Board Location ················································ 14
5-2. Block Diagrams ··························································· 15
5-3. Printed Wiring Board – CD Section – ························ 17
5-4. Schematic Diagram – CD Section – ··························· 18
5-5. Printed Wiring Board – MAIN Board – ····················· 19
5-6. Schematic Diagram – MAIN Board (1/4) – ··············· 20
5-7. Schematic Diagram – MAIN Board (2/4) – ··············· 21
5-8. Schematic Diagram – MAIN Board (3/4) – ··············· 22
5-9. Schematic Diagram – MAIN Board (4/4) – ··············· 23
5-10. Printed Wiring Board
5-2. Block Diagrams ··························································· 15
5-3. Printed Wiring Board – CD Section – ························ 17
5-4. Schematic Diagram – CD Section – ··························· 18
5-5. Printed Wiring Board – MAIN Board – ····················· 19
5-6. Schematic Diagram – MAIN Board (1/4) – ··············· 20
5-7. Schematic Diagram – MAIN Board (2/4) – ··············· 21
5-8. Schematic Diagram – MAIN Board (3/4) – ··············· 22
5-9. Schematic Diagram – MAIN Board (4/4) – ··············· 23
5-10. Printed Wiring Board
– Address Sensor, Driver Motor Section – ·················· 24
5-11. Printed Wiring Board – Panel Section – ····················· 25
5-12. Schematic Diagram – Panel Section – ······················· 26
5-13. Printed Wiring Board – POWER Board – ·················· 27
5-14. Printed Wiring Board – Trans Section – ····················· 28
5-15. Schematic Diagram – Trans Section – ······················· 29
5-16. IC Block Diagrams ······················································ 30
5-17. IC Pin Function Description ········································ 32
5-12. Schematic Diagram – Panel Section – ······················· 26
5-13. Printed Wiring Board – POWER Board – ·················· 27
5-14. Printed Wiring Board – Trans Section – ····················· 28
5-15. Schematic Diagram – Trans Section – ······················· 29
5-16. IC Block Diagrams ······················································ 30
5-17. IC Pin Function Description ········································ 32
6. EXPLODED VIEWS
······················································ 34
6-1. MAIN SECTION ························································ 34
6-2. FRONT PANEL SECTION ········································· 35
6-3. MAIN BOARD SECTION ·········································· 36
6-4. CD MECHANISM DECK SECTION ························ 37
6-2. FRONT PANEL SECTION ········································· 35
6-3. MAIN BOARD SECTION ·········································· 36
6-4. CD MECHANISM DECK SECTION ························ 37
7. ELECTRICAL PARTS LIST
······································· 38
3
HCD-RG11
This section is extracted
from instruction manual.
from instruction manual.
SECTION 1
GENERAL
Main unit
1
2
3
4 5 6
7
8
9
q;
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
wa
ws
wd
wf
wg
wh
wj
wk
AUDIO jacks wd (19)
CD wk (10 – 12, 15)
CD SYNC qh (15)
Deck A ws (14)
Deck B qs (14 – 16)
DISC 1 – 3 4 (10, 11)
DISC SKIP EX-CHANGE 3
CD wk (10 – 12, 15)
CD SYNC qh (15)
Deck A ws (14)
Deck B qs (14 – 16)
DISC 1 – 3 4 (10, 11)
DISC SKIP EX-CHANGE 3
(10, 11)
Disc tray 5 (10)
DISPLAY w; (12)
EFFECT ON/OFF qd
DISPLAY w; (12)
EFFECT ON/OFF qd
(17)
GAME wg (18 – 20)
BUTTON DESCRIPTIONS
?/1 (power) 1
Z OPEN/CLOSE 6
Z (deck B) qa
M (fast forward) qf
. (go back) qj
> (go forward) qj
X (pause) qj
H (play) qj
x (stop) qj
m (rewind) qk
Z (deck A) wa
Z OPEN/CLOSE 6
Z (deck B) qa
M (fast forward) qf
. (go back) qj
> (go forward) qj
X (pause) qj
H (play) qj
x (stop) qj
m (rewind) qk
Z (deck A) wa
GAME EQ ql (17, 18, 20)
GROOVE 8 (17)
MOVIE EQ 7 (17)
MUSIC EQ 2 (17)
PHONES jack q;
REC PAUSE/START qg (15)
TAPE A/B wh (14, 15)
TUNER/BAND wj (12, 13, 15)
VIDEO jack wf (19, 20)
VOLUME control 9
GROOVE 8 (17)
MOVIE EQ 7 (17)
MUSIC EQ 2 (17)
PHONES jack q;
REC PAUSE/START qg (15)
TAPE A/B wh (14, 15)
TUNER/BAND wj (12, 13, 15)
VIDEO jack wf (19, 20)
VOLUME control 9
4
HCD-RG11
Remote Control
1 2 3 4
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
wa
CD ql (10 – 12, 15)
CLEAR w; (11)
CLOCK/TIMER SELECT 2
CLEAR w; (11)
CLOCK/TIMER SELECT 2
(16, 19)
CLOCK/TIMER SET 3 (9, 16,
18)
DISPLAY 6 (12)
D.SKIP 7 (10)
ENTER qg (9, 11 – 13, 16, 18,
D.SKIP 7 (10)
ENTER qg (9, 11 – 13, 16, 18,
19)
EQ +/– qf (17)
GAME q; (18 – 20)
GROOVE qd (17)
GAME q; (18 – 20)
GROOVE qd (17)
ON/OFF qh (17)
PLAY MODE wa (10, 11)
PRESET +/– 5 (13)
REPEAT 8 (11)
SLEEP 1 (18)
STEREO/MONO 8 (13)
SURROUND qa (17)
TAPE A/B 9 (14, 15)
TUNER MEMORY qj (12, 13)
TUNER/BAND qk (12, 13)
TUNING +/– 5 (12, 13)
VOL +/– qs
PLAY MODE wa (10, 11)
PRESET +/– 5 (13)
REPEAT 8 (11)
SLEEP 1 (18)
STEREO/MONO 8 (13)
SURROUND qa (17)
TAPE A/B 9 (14, 15)
TUNER MEMORY qj (12, 13)
TUNER/BAND qk (12, 13)
TUNING +/– 5 (12, 13)
VOL +/– qs
BUTTON DESCRIPTIONS
?/1 (power) 4
M (fast forward) 5
. (go back) 5
> (go forward) 5
X (pause) 5
N (play) 5
m (rewind) 5
x (stop) 5
M (fast forward) 5
. (go back) 5
> (go forward) 5
X (pause) 5
N (play) 5
m (rewind) 5
x (stop) 5
Setting the time
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
Proceed to step 5 when “CLOCK” appears
in the display.
in the display.
3
Press
.
or
>
repeatedly to select
“SET CLOCK”.
4
Press ENTER on the remote.
5
Press
.
or
>
repeatedly to set the
hour.
6
Press ENTER on the remote.
The minute indication flashes.
7
Press
.
or
>
repeatedly to set the
minute.
8
Press ENTER on the remote.
Tip
If you made a mistake or want to change the time,
start over from step 2.
start over from step 2.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
5
HCD-RG11
SECTION 2
DISASSEMBLY
2-1. Case (Top)
Note :
Disassemble the unit in the order as shown below.
Note :
Follow the disassembly procedure in the numerical order given.
4
qa
q;
q;
8
case (Top)
case (Side-L)
case (Side-R)
5
two screws (Case 3 TP2)
7
two screws
(+BVTP 3
×
10)
3
two screws
(+BVTP 3
×
10)
1
two screws (Case 3 TP2)
9
four screws (+BVTP 3
×
6)
6
screw (Case 3 TP2)
2
screw (Case 3 TP2)
CD DOOR
SET
CASE (TOP)
FRONT PANEL SECTION AND CD MECHANISM
DECK (CDM58F-K6) SECTION
DECK (CDM58F-K6) SECTION
BASE UNIT
CD BOARD, DRIVER BOARD, MOTOR BOARD AND
ADDRESS SENSOR BOARD
ADDRESS SENSOR BOARD
PANEL BOARD
TAPE MECHANISM DECK AND PANEL BOARD
CD BOARD
SUB TRANS BOARD, VIDEO OUT BOARD AND TRANS BOARD
MAIN BOARD AND POWER BOARD
