DOWNLOAD Sony HCD-NXM2D Service Manual ↓ Size: 5.01 MB | Pages: 101 in PDF or view online for FREE

21

In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.

1.

Set correctly the disc type to be used on the Disc Type
screen.

2. In case of an alarm, immediately press the  x  button

to stop the servo operation, and press the  +/1  button to
turn the power off.

(controllable from front panel or remote commander)
 +/1

: Power OFF (release the Test Mode)

 x

: Servo stop

 Z

: Stop and eject/Loading

[RETURN]

: Return to Operation Menu or Test
  Mode Menu

[         PREV], [NEXT           ]

: Transition between sub modes of menu

[1] to [9], [10/0]

: Selection of menu items

Cursor  o / O

: Increase/Decrease in manually
   adjusted value

Disc Type

Disc Type Select

 1. Disc Type Auto Check

 2. Set Disc Type DVD

 3. Set Disc Type CD

 4. Set Disc Type Hybrid

Exit: RETURN

2-1-1.

Disc Type Auto Check

1) Press the [1] key on the remote commander to display the Disc

Type Auto Check screen.

2) Insert a disc and press the [ENTER]  key on the remote

commander.

3) It judges the type of inserted disc automatically and displays

the disc type and so on as below.

Disc Type Auto Check

 Disc Type

xx

 Layer

xx

 Mirr Time

xx

 Mirr Count

xx

 FZC Count

xx

 PI Reference xx

 PI Peak

xx

 ENTER.Execute

Exit: RETURN

Disc Type

: CD, DVD or Hybrid (SACD)

Layer

: SINGLE, DUAL or HYBRID

Mirr Time

: Mirror time of between disc surface and record
  surface when disc type judgment. (hexadecimal
  number)

1-3.  DVD-DL (dual layer)
Press the [3] key on the remote commander and insert a DVD dual
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.

1.

Sled tilt reset

2.

Disc check memory DL

3.

Wait 500 msec

4.

Set disc type DL

5.

LD on

6.

Spindle start

7.

Wait 1 sec

Layer 1 Adjust

8.

Focus servo on 0

9.

Auto track offset adjust

10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 500 msec
14. Sled on
15. Check CLV lock
16. Auto loop filter offset adjust, Auto focus adjust
17. Auto focus gain adjust
18. Auto focus offset adjust
19. EQ boost adjust
20. Auto loop filter offset adjust
21. Auto Track Gain Adjust

Layer 0 Adjust

22. Focus jump (L1 t L0)
23. Auto track offset adjust L0
24. CLVA on
25. Wait 500 msec
26. Tracking on
27. Wait 500 msec
28. Sled on
29. Check CLV lock
30. Auto Focus Adjust
31. Auto focus gain adjust
32. Auto focus offset adjust
33. EQ boost adjust
34. Auto track gain adjust
35. All servo stop

Note: This mode is used for design, and not used in service fundamen-

tally.

On the Test Mode Menu screen, press the [2] key on the remote
commander, and the Operation Menu will be displayed. For the
manual operation, each servo on/off control and adjustment can be
executed manually.

## Drive Manual Operation ##

Operation Menu

 1. Disc Type

 2. Servo Control

 3. Track/Layer Jump

 4. Non EEPROM Write Adjust

 5. EEPROM Write Adjust

 6. Memory Check

 7. Disc Check Memory

 8. Error Rate Display

 9. SACD Water Mark

Exit: RETURN

 >

.

22

Mirr Count

: The number of times which mirror
  counts between disc surface and record
  surface when disc type judging.

FZC Count

: The number of times which focus zero
  cross points of each layer when lens
  down.

PI Reference

: The average of PI reference voltage.
  (hexadecimal number)

PI Peak

: PI peak level voltage. It performs only
  when disc type judgment is successful.
  (hexadecimal number)

2-1-2.

Disc Type DVD

It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]: DVD single layer disc (12 cm)
[2]: DVD dual layer disc (0 layer, 12 cm)
[3]: DVD dual layer disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layer disc (0 layer, 8 cm)
[7]: DVD dual layer disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)

2-1-3.

Disc Type CD

It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]: CD disc (normal speed, 12 cm)
[2]: CD disc (double speed, 12 cm)
[3]: CD disc (normal speed, 8 cm)
[4]: CD disc (double speed, 8 cm)
[5]: CD-RW disc (normal speed, 12 cm)
[6]: CD-RW disc (double speed, 12 cm)
[7]: CD-RW disc (normal speed, 8 cm)
[8]: CD-RW disc (double speed, 8 cm)

2-1-4.

Disc Type Hybrid

It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]: SACD Hybrid disc (SACD layer, 12 cm)
[2]: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]: SACD Hybrid disc (SACD layer, 8 cm)
[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]: SACD Hybrid disc (CD layer, double speed, 8 cm)

Note: Be sure to perform the disc type setup before performing this item.

Servo Control

 1.LD

off R.Sled FWD

 2.Focus

off L.Sled REV

 3.SPDL

off U.Sled Reset

 4.CLVA

off D.Sled Limit

 5.Trk.

off

 6.Sled

off

 7.Fcs.Srch

off

 0.All Servo Off

Exit: RETURN

On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.

[1] LD

: Turn on/off the laser.

[2] Focus

: Search the focus and turn on the focus.

[3] SPDL

: Turn on/off the spindle.

[4] CLVA

: Turn on/off normal servo of spindle servo.

[5] Trk.

: Turn on/off the tracking servo.

[6] Sled

: Turn on/off the sled servo.

[7] FCS. Srch : Turn on/off the focus search.
[10/1]

: All servo off.

[R] Sled FWD (right cursor) : Move the sled forward.
[L] Sled REV (left cursor)

: Move the sled reverse.

[U] Sled FWD (up cursor)

: Reset the sled.

[D] Sled REV (down cursor) : Limit in the sled.

Track/Layer Jump

 1.  1Tj

FWD

 2.  1Tj

REV

 3.500Tj Fine

FWD

 4.500Tj Fine

REV

 5.10kTj Dirc

FWD

 6.10kTj Dirc

REV

 7.20kTj Dirc

FWD

 8.20kTj Dirc

REV

 0. All Servo Off

Exit: RETURN

On this screen, track jump, etc. can be performed. Only for the DVD
dual layer disc, the focus jump and layer jump are displayed in the
right field

[1] 1Tj FWD

: 1 track jump forward.

[2] 1Tj REV

: 1 track jump reverse.

[3] 500Tj FWD

: 500 track jump (fine search)forward.

[4] 500Tj REV

: 500 track jump (fine search) reverse.

[5] 10kTj FWD

: 10k track jump (direct search) forward.

[6] 10kTj REV

: 10k track jump (direct search) reverse.

[7] 20kTj FWD

: 20k track jump (direct search) forward.

[8] 20kTj REV

: 20k track jump (direct search) reverse.

[10/0]

: All servo off.

Non EEPROM Write Adjust

 1. Focus Offset

 2. Focus Gain

 3. Trk.

Offset Coarse

 4. Trk.

Offset Fine

 5. Trk.

Gain

 6. EQ

Boost

 0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted manually. Select the desired
number [1] to [10/0] from the remote commander, and current setting for
the selected item will be displayed, then increase or decrease numeric
value with the O key or  o key. If CLV has been applied, the jitter is
displayed for reference for the adjustment.

23

[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain

: Adjusts focus gain.

[3] TRK. Offset coares :

  Adjusts tracking offset of the RF amp
  (IC001) side.

[4] TRK. Offset fine :

   Adjusts tracking offset of the DSP (IC401)
  side.

[5] TRK. Gain

: Adjusts track gain.

[6] EQ Boost

: Adjusts amount of boost of equalizer.

[10/0]

: All servo off.

EEPROM Write Adjust

 1. Focus

Offset

 2. Focus

Gain

 3. Trk.

Offset Coarse

 4. ——————

 5. Trk.

Gain

 6. EQ

Boost

 0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted automatically. Select the
desired number [1]  to  [10/0]  from the remote commander, and
selected item is adjusted automatically.

[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain

: Adjusts focus gain.

[3] TRK. Offset coarse :

  Adjusts tracking offset of the RF amp
 (IC001) side.

[5] TRK. Gain

: Adjusts track gain.

[6] EQ Boost

: Adjusts amount of boost of equalizer.

[10/0]

: All servo off.

2-6.  Memory Check
Display images are shown as follows, and all two screens are able
to switch by the O key (UP) or  o key (DW).

EEPROM Data 1/2

CD

SL

L0

L1

Focus

Gain

xx

xx

xx

xx

Trk.

Gain

xx

xx

xx

xx

Focus

Offset

xx

xx

xx

xx

Trk.

Offset

xx

xx

xx

xx

EQ.

Boost

xx

xx

xx

xx

PI

Level

xx

xx

--

--

Fcs. Balance

--

xx

--

--

Jitter

xx

xx

xx

xx

Mirror Time

xx

xx

xx

--

FE Level

--

xx

--

--

Traverse Lv1.

--

xx

--

--

Next:DW Default:CLR

Exit:RET

EEPROM Data 2/2

CDRW DVDRW

Focus

Gain

xx

xx

Trk.

Gain

xx

xx

Focus

Offset

xx

xx

Trk.

Offset

xx

xx

EQ.

Boost

xx

xx

Prev:UP Default:CLR

Exit:RET

On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
[CLEAR]  key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if [0]-All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.

Disc Check Memory

 1. SL Disc check

 2. CD Disc check

 3. DL Disc check

Exit: RETURN

On this screen, measure the mirror time of chucked disc, and write
to the EEPROM.

Error Rate Display

UC

CR

Address

PI1 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx

PI2 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx

PO  Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx

START: ENTER

STOP: RETURN

On this screen, measure and display the error rate.

UC : Incorrect value
CR

: Correct value

Add : Address

24

SACD Water Mark Check

 PSP AMP

 PSN

 Adjust Error Failed

 Start: ENTER

Stop: RETURN

On this screen, measure the PSP AMP value and PSN value of SACD
water mark.

On the Test Mode Menu screen, selecting [3] executes the aging of
the mechanism deck.

## Aging Test MENU ##

**

 Pls use over 40min. CD 

**

Operation Menu

1. Open/Close Test

Exit: RETURN

1) On the Aging Test MENU screen, press the [1]  key on the

remote commander to display the Open/Close Test screen.

2) Insert discs and press the [ENTER]  key on the remote

commander.

3) Is starts the aging.

During aging, the disc number, operating status and repeat
cycle are displayed. Aging can be aborted at any time by
pressing the [RETURN] key. After the operation is stopped,
press the [RETURN] key to return to the Aging Test MENU.

On the Test Mode Menu screen, selecting [4]  displays the
information such as servo emergency history.
The history information from last 1 up to 10 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.

### EMG. History ###

  Laser Hours

CD

xxxxhxxm

DVD

xxxxhxxm

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

   Select:1-9

Scroll:UP/DOWN

  (1.Latest EMG.)

Exit: RETURN

xxxxhxxm

: The laser on total hours. Data below
   minutes are omitted.

a.

: Error number.

bb

: Error code.

xx

: Not used.

• Clearing History Information

Press the [DVD DISPLAY] and [CLEAR] keys in this order.
Then both CD and DVD data are cleared.

Press the [DVD TOP MENU] and [CLEAR] keys in this order.

Press [DVD MENU] and [CLEAR] keys in this order.
The data have been initialized when “EEPROM Initialize
Finished”  message is displayed.

• Code list of Emergency History

10 : Communication to RF AMP (IC001) failed.
11 : Each servo for focus, tracking, and spindle is unlocked.
12 : Check sum error of EEPROM (IC204).
14 : Communication to servo DSP (IC509) failed, or servo

DSP  (IC509) is faulty.

15 : Communication to DVD decoder (IC701) failed, or DVD

decoder (IC701) is faulty.

16 : Communication to DSD decoder (IC801) failed, or DSD

decoder (IC801) is faulty. (Not used)

20 : Initialization of sled servo failed. It is not placed in the

initial position.

23 : Sled servo operation error.
24 : Made a request to move the sled servo to wrong position.
30 : Tracking balance adjustment error.
31 : Tracking gain adjustment error.
33 : Focus bias adjustment error.
34 : Focus gain adjustment error.
35 : Equalizer adjustment error.
40 : Focus servo does not operate.
41 : With a DVD dual layer disc, focus jump failed.
50 : CLV (spindle) servo does not operate.
51 : Spindle does not stop.
60 : Made a request to seek nonexistent address.
61 : Seek error of retry more than regulated times.
70 : Control data could not be read.
80 : Disc reading failed.

5. MECHA  ERROR  HISTORY
On the Test Mode Menu screen, selecting [5]  displays the
information of mechanism deck error history.
The history information from last 1 up to 8 can be scrolled with
the O key or o key.

### Mecha Error History ###

  1. xx xx xx xx xx xx xx xx

  2. xx xx xx xx xx xx xx xx

  3. xx xx xx xx xx xx xx xx

  4. xx xx xx xx xx xx xx xx

  5. xx xx xx xx xx xx xx xx

  6. xx xx xx xx xx xx xx xx

  7. xx xx xx xx xx xx xx xx

  8. xx xx xx xx xx xx xx xx

Scroll:UP/DOWN

(1.Latest Err.)

Exit: RETURN