Sony HCD-M700 Service Manual ▷ View online
6
HCD-M700
Smart Space
The signal was input again after silence continued
for 3 or more but less than 30 seconds during
digital recording, and the silence was cut to 3
seconds.
for 3 or more but less than 30 seconds during
digital recording, and the silence was cut to 3
seconds.
Step Full!
You tried to program 26 or more tracks (steps).
TOC Reading
The MD deck is reading the TOC information of
the MD.
the MD.
TOC Writing
The MD deck is writing the information of
recorded or edited contents.
Track End
You have reached the end of the track while
adjusting the dividing point during the Divide
Function.
adjusting the dividing point during the Divide
Function.
Tr Protect
You attempted to erase a protected track.
DVD
No Disc
There is no DVD in the player.
Push STOP!
You pressed PLAY MODE (or PLAY MODE/
TUNING MODE on the remote) during play.
TUNING MODE on the remote) during play.
Cannot use
You pressed an invalid button.
CD
No Disc
There is no CD in the player.
OVER
You have reached the end of the CD while
pressing M during play or pause.
pressing M during play or pause.
Step Full!
You tried to program 26 or more tracks (steps).
Self-diagnosis display (continued)
Incomplete!
Adjustment of the recording level after recording
or Fade-in and Fade-out procedures have failed
since the system was either subject to vibration or
there is a damaged or dirty disc in the tray.
or Fade-in and Fade-out procedures have failed
since the system was either subject to vibration or
there is a damaged or dirty disc in the tray.
Initialize
The power was off for a long time, so the system is
initializing itself.
initializing itself.
Name Full
There is no more space to store track, disc or group
titles.
titles.
No Change
While attempting to change the recording level
after recording, you pressed ENTER/YES on the
remote without actually changing the recording
level, so no change was made.
after recording, you pressed ENTER/YES on the
remote without actually changing the recording
level, so no change was made.
No Disc
There is no disc in the MD deck.
–OVER–
You have reached the end of the MD while
pressing M during playing pause.
pressing M during playing pause.
Push STOP!
You pressed PLAY MODE (or PLAY MODE/
TUNING MODE on the remote) during play.
TUNING MODE on the remote) during play.
—Rehearsal—
The MD is playing the specified point for
confirmation during the A-B Erase Function and
the Divide Function.
confirmation during the A-B Erase Function and
the Divide Function.
S.F Edit!
You attempted to perform another operation while
in S.F Edit (changing the recording level after
recording, Fade-in, Fade-out) mode.
in S.F Edit (changing the recording level after
recording, Fade-in, Fade-out) mode.
S.F Edit NOW
You pressed ?/1 while in S.F Edit (changing the
recording level after recording, Fade-in, Fade-out)
mode.
recording level after recording, Fade-in, Fade-out)
mode.
TAPE
Cannot SYNC!
There is no tape in the tape deck, or the tab has
been removed from the cassette.
been removed from the cassette.
No Tab
You cannot record the tape because the tab has
been removed from the cassette.
been removed from the cassette.
No Tape
There is no tape in the tape deck.
TUNER
WAIT
The function is switching to the tuner.
7
HCD-M700
How to Operate the Self-diagnostics Function (Error History Display Mode)
Note:
Note:
Use the self-diagnostics function in the "error history display mode" of the test mode. The least required procedure is described
below. Do not enter any other modes by mistake. If you have entered any other modes accidentally, press the MENU/NO “R”
button to exit the mode.
below. Do not enter any other modes by mistake. If you have entered any other modes accidentally, press the MENU/NO “R”
button to exit the mode.
1.
Press the
?/1
button to turn on the power.
2.
Press the FUNCTION button to select the “MD” function.
3.
While pressing the x button and the REC MODE button at the same time, press the FUNCTION button.
4.
Press the MD
>
“R” button to display “[Service]”. Then press the ENTER/YES “R” button.
5.
Press the MD
>
“R” button to display “Err Display”.
6.
Press the ENTER/YES “R” button to enter the error history display mode and “op rec tm” appears.
7.
Select the desired contents that you want to display or to execute using the MD
.
“R” button or the MD
>
“R” button.
8.
Press the REC MODE button to display or to execute the selected contents.
9.
Press the REC MODE button again to return to step 7.
10. Press the MENU/NO “R” button. The message “Err Display” appears and you exit the error history mode.
11. Press the REPEAT button twice to exit the test mode.
12. Press the
11. Press the REPEAT button twice to exit the test mode.
12. Press the
?/1
button to turn off the power.
Note 1:
About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SM700E/provided with unit) buttons. These
operations are indicated as “R” in this manual.
As this unit has only a few buttons, some operations require the use of remote commander (RM-SM700E/provided with unit) buttons. These
operations are indicated as “R” in this manual.
Example:
MENU/NO “R”
...Press the
MENU/NO
button of the remote commander.
Note 2:
Incorrect operations may be performed if the test mode is not entered properly.
In this case, press the ?
In this case, press the ?
/1
button to turn the power off, and retry to enter the test mode.
8
HCD-M700
Items of Error History Mode Items and Contents
Selecting the Test Mode
Display
op rec tm
op play tm
spdl rp tm
retry err
total err
err history
retry adrs
er refresh
op change
spdl change
History
Displays the accumulated recording time.
When the accumulated recording time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
The display time indicates the time when the laser is set to high power more, which is about 1/4 of the actual
recording time.
When the accumulated recording time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
The display time indicates the time when the laser is set to high power more, which is about 1/4 of the actual
recording time.
Displays the accumulated playback time.
When the accumulated playback time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
When the accumulated playback time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
Displays the accumulated rotating time of the spindle motor.
When the accumulated rotating time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
When the accumulated rotating time is more than 1 minute, displays the hour and minute
When less than 1 minute, displays “Under 1 min”
Displays the accumulated number of retry errors during recording and playback
Displays “r
Displays “r
p
”.
is the number of errors during recording.
is the number of errors during playback.
This is displayed in hexadecimal from 00 to FF.
Displays the total number of errors
Displays “total
Displays “total
”. This is displayed in hexadecimal from 00 to FF.
Displays the past ten errors.
Displays “0x ErrCd@@”.
X is the history number. The younger the number, the more recent is the history (00 is the latest). @@ is the
error code.
Select the error history number by pressing the MD
Displays “0x ErrCd@@”.
X is the history number. The younger the number, the more recent is the history (00 is the latest). @@ is the
error code.
Select the error history number by pressing the MD
.
“R” or MD
>
“R” button.
Displays the past five retry addresses.
Displays “
Displays “
ADRS
”,
is the history number,
is the cluster with the retry error.
Select the error history number by pressing the MD
.
“R” or MD
>
“R” button.
Mode for erasing the error and retry address histories
Procedure
1. Press the REC MODE button when displayed as “er refresh”.
2. When the display changes to “er refresh?”, press the ENTER/YES “R” button
When “Complete!!” is displayed, it means erasure has completed.
Be sure to check the following after executing this mode.
*Data has been erased.
*Perform recording and playback, and check that the mechanism is normal.
Procedure
1. Press the REC MODE button when displayed as “er refresh”.
2. When the display changes to “er refresh?”, press the ENTER/YES “R” button
When “Complete!!” is displayed, it means erasure has completed.
Be sure to check the following after executing this mode.
*Data has been erased.
*Perform recording and playback, and check that the mechanism is normal.
Mode for erasing the accumulated time of op rec tm, op play tm.
Use these histories as a guide line for the time of replacement of the optical pick-up. If the optical pick-up
has been replaced, perform this procedure and erase the past history.
Procedure
1. Press the REC MODE button when displayed as “op change”.
2. When the display changes to “op change?”, press the ENTER/YES “R” button.
When “Complete!!” is displayed, it means erasure has completed.
Use these histories as a guide line for the time of replacement of the optical pick-up. If the optical pick-up
has been replaced, perform this procedure and erase the past history.
Procedure
1. Press the REC MODE button when displayed as “op change”.
2. When the display changes to “op change?”, press the ENTER/YES “R” button.
When “Complete!!” is displayed, it means erasure has completed.
Mode for erasing the accumulated spdl rp tm time
Use these histories as the guide line for the time of replacement of the spindle motor. If the spindle motor has
been replaced, perform this procedure and erase the past history.
Procedure
1. Press the REC MODE button when displayed as “spdl change”
2. When the display changes to “spdl change?”, press the ENTER/YES “R” button.
When “Complete!!” is displayed, it means erasure has completed.
Use these histories as the guide line for the time of replacement of the spindle motor. If the spindle motor has
been replaced, perform this procedure and erase the past history.
Procedure
1. Press the REC MODE button when displayed as “spdl change”
2. When the display changes to “spdl change?”, press the ENTER/YES “R” button.
When “Complete!!” is displayed, it means erasure has completed.
9
HCD-M700
Table of Error Codes
Error Code
Description
10
11
12
20
21
22
23
24
30
31
40
41
42
43
50
51
Could not perform loading
The changer error occurred
Loading switches combined incorrectly
Timed out without reading the top of PTOC
Could read top of PTOC, but detected error
Timed out without accessing UTOC
Timed out without reading UTOC
Error in UTOC
Could not start playback
Error in sector
A cause of retry occurred during normal recording
Retried due to DRAM overflow
Retry occurred during TOC writing
Retry aborted during S.F editing
Other than access processing, and could not read address.
Focus NG occurred and overran.
Click on the first or last page to see other HCD-M700 service manuals if exist.