Sony HCD-M700 Service Manual ▷ View online
11
HCD-M700
Jig For Checking DVD Board and DIGITAL Board Waveform
The special jig (J-2501-196-A) is useful for checking the waveform of the DVD board and DIGITAL board.
• Extention cable (10P)
(J-2501-219-A)
• Extention cable (27P)
(J-2501-220-A)
jig (10P)
(J-2501-219-A)
(J-2501-219-A)
jig (27P)
(J-2501-220-A)
(J-2501-220-A)
CN607
CN608
CN705
DVD board
CONTROL board
CN101
DIGITAL board
• DISC TRAY LOCK
If the disc tray does not open and the message “LOCKED” appears,
press the two buttons of ENTER/START and Z DVD at the same
for 5 seconds or longer.
Then the lock is released, the message “UNLOCKED” appears for
2 seconds and the disc tray opens.
press the two buttons of ENTER/START and Z DVD at the same
for 5 seconds or longer.
Then the lock is released, the message “UNLOCKED” appears for
2 seconds and the disc tray opens.
12
HCD-M700
Iop DATA RECORDING AND DISPLAY WHEN OPTICAL PICK-UP AND NON-VOLATILE MEMORY (IC195 OF
BD BOARD) ARE REPLACED
BD BOARD) ARE REPLACED
The Iop value labeled on the optical pick-up can be stored in the non-volatile memory. By storing the value, it will eliminate the need to look
at the value on the label of the optical pick-up. When replacing the optical pick-up or non-volatile memory (IC195 of BD board), store the Iop
value on the optical pick-up according to the following procedure.
at the value on the label of the optical pick-up. When replacing the optical pick-up or non-volatile memory (IC195 of BD board), store the Iop
value on the optical pick-up according to the following procedure.
Record Precedure:
1. Press the ?/1
1. Press the ?/1
button to turn on the power.
2. Press the FUNCTION button to select the “MD” function.
3. While pressing the x button and the REC MODE button at the same time, press the FUNCTION button.
4. Press the MD
3. While pressing the x button and the REC MODE button at the same time, press the FUNCTION button.
4. Press the MD
>
“R” button to display “[Service]”. Then press the ENTER/YES “R” button.
5. Press the MD
>
“R” button to display “Iop Write” (C05) and press the ENTER/YES “R” button.
6. The display becomes “Ref=@@@.@” (@ is an arbitrary number) and the numbers which can be changed will blink.
7. Input the Iop value written on the optical pick-up.
7. Input the Iop value written on the optical pick-up.
To select the number : Press the MD
.
“R” button or the MD
>
“R” button.
To select the digit
: Press the REC MODE button.
8. When the ENTER/YES “R” button is pressed, the display becomes “Measu=@@@.@” (@ is an arbitrary number).
9. As the adjustment results are stored for the 6 value. Leave it as it is and press the ENTER/YES “R” button.
10. “Complete!” will be displayed momentarily. The value will be stored in the non-volatile memory and the display will become “Iop
9. As the adjustment results are stored for the 6 value. Leave it as it is and press the ENTER/YES “R” button.
10. “Complete!” will be displayed momentarily. The value will be stored in the non-volatile memory and the display will become “Iop
Write” (C05).
11. Press the REPEAT button twice to exit the mode.
12. Press the ?/1 button to turn off the power.
12. Press the ?/1 button to turn off the power.
Display Precedure:
1. Press the ?/1 button to turn on the power.
2. Press the FUNCTION button to select the “MD” function.
3. While pressing the x button and the REC MODE button at the same time, press the FUNCTION button.
4. Press the MD
1. Press the ?/1 button to turn on the power.
2. Press the FUNCTION button to select the “MD” function.
3. While pressing the x button and the REC MODE button at the same time, press the FUNCTION button.
4. Press the MD
>
“R” button to display “[Service]”. Then press the ENTER/YES “R” button.
5. Press the MD
>
“R” button to display “Iop Read” (C26) and press the ENTER/YES “R” button.
6. “@@.@/##.#” is displayed and the recorded contents are displayed.
@@.@ : indicates the Iop value labeled on the optical pick-up
##.#
##.#
: indicates the Iop value after adjustment
7. To end, press the MENU/NO “R” button to display “Iop Read” (C26). Then press the REPEAT button twice.
8. Press the ?/1 button to turn off the power.
8. Press the ?/1 button to turn off the power.
Checks Prior to Parts Replacement and Adjustments in MD
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “Section 5 Electrical Adjustments”.
Details of the procedures are described in “Section 5 Electrical Adjustments”.
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments.
When performing adjustments, use the specified values for adjustments.
When performing adjustments, use the specified values for adjustments.
• 0.93 mW power
Specified value : 0.85 to 0.91 mW (KMS-260B)
0.80 to 0.96 mW (KMS-260E)
• 7.25 mW power
Specified value : 6.8 to 7.2 mW (KMS-260B)
7.0 to 7.5 mW (KMS-260E)
• Iop (at 7.25mW)
Labeled on the optical pick-up
Iop value
± 10mA
• Unsatisfactory if displayed as “NG : XXXX”NG
(XXXX are arbitrary numbers)
• Unsatisfactory if displayed as “T=@@ (##) [NG]”
NG
(@@, ## are both arbitrary numbers)
Laser power check
(6-2 : See page 36)
Auto check
(6-4 : See page 37)
Temperature
Temperature
compensation
offset check
(6-1 : See page 36)
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
(Unsatisfactory if specified value is not satisfied)
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
• Replace the optical pick-up
• Replace the optical pick-up
• Check for disconnection of the circuits around
D101 (BD board)
• Check the signals around IC101, IC151, CN102,
CN103 (BD board)
Measure if unsatisfactory
13
HCD-M700
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Main unit
ALPHABETICAL ORDER
A – P
DIRECTION qk (63–65)
Disc tray 0 (12)
Display window 2
DVD NX w; (12, 13, 16, 18)
ENTER/START qf (40, 41, 64)
FUNCTION ws (12, 14, 33, 35,
Disc tray 0 (12)
Display window 2
DVD NX w; (12, 13, 16, 18)
ENTER/START qf (40, 41, 64)
FUNCTION ws (12, 14, 33, 35,
36, 39, 41–45, 47, 48, 50–56,
58, 63, 65, 74)
58, 63, 65, 74)
MD slot 7 (33)
MD NX w; (33, 34, 36, 39, 41)
PHONES jack ql
PLAY MODE qk (12, 14, 15, 33,
MD NX w; (33, 34, 36, 39, 41)
PHONES jack ql
PLAY MODE qk (12, 14, 15, 33,
35, 41, 47)
REC MODE qg (40–42)
Remote sensor 5
REPEAT/FM MODE qj (13, 34,
Remote sensor 5
REPEAT/FM MODE qj (13, 34,
61, 62)
SYNCHRO MODE qh (40, 41,
64)
TAPE nN wa (63–65)
TUNER BAND wa (60–62)
TUNING +/– 3 (60–62)
TUNING MODE qk (60–62)
VOLUME +/– 8
TUNER BAND wa (60–62)
TUNING +/– 3 (60–62)
TUNING MODE qk (60–62)
VOLUME +/– 8
R – V
?/1 (power) 1
m/M 3
l/L 3
x 4
Z DVD 9
Z MD 6
z MD qd
z TAPE qa
X TAPE qs
m/M 3
l/L 3
x 4
Z DVD 9
Z MD 6
z MD qd
z TAPE qa
X TAPE qs
BUTTON DESCRIPTIONS
x
+
–
X
z
z
Z
Z
nN
NX
NX
?/1
lm
ML
1
3
6
ws
7
8
5
9
0
2
4
qk
ql
qj
qs
qd qa
w;
wa
qg
qh qf
14
HCD-M700
Remote Control
ANGLE eg (28)
AUDIO ej (25)
BASS/TREBLE qd (65)
BGMD wl (70)
CLEAR el (14, 15, 17, 27, 35,
AUDIO ej (25)
BASS/TREBLE qd (65)
BGMD wl (70)
CLEAR el (14, 15, 17, 27, 35,
49, 62)
CLOCK/TIMER SELECT rs
(69, 70)
CLOCK/TIMER SET rd (11, 68,
69)
CURSOR T/t 5 (11, 48, 49)
DISPLAY w; (23, 35, 63, 71, 72)
DSG qs (65)
DVD DISPLAY qg (16, 17, 19,
DISPLAY w; (23, 35, 63, 71, 72)
DSG qs (65)
DVD DISPLAY qg (16, 17, 19,
20, 23–25, 27–29, 66)
DVD MENU qa (17)
DVD TOP MENU qj (17)
DVD SETUP eh (19, 30)
DVD N/SELECT wa (12–18,
DVD TOP MENU qj (17)
DVD SETUP eh (19, 30)
DVD N/SELECT wa (12–18,
21, 32, 42)
DVD X wa (13, 42)
DVD x wa (13, 16, 18, 29)
DVD ./> 7 (13, 14, 18)
DVD t
DVD x wa (13, 16, 18, 29)
DVD ./> 7 (13, 14, 18)
DVD t
/
T 8 (13)
ENTER/YES wd (11, 14, 35,
42–60, 62, 68–70)
FUNCTION ql (12, 14, 33, 35,
36, 39, 41–45, 47, 48, 50–56,
58, 63, 65, 74)
58, 63, 65, 74)
GROUP ra (36, 38–40, 48–51)
GROUP SKIP wk (36, 39, 40, 48,
GROUP SKIP wk (36, 39, 40, 48,
49, 51)
MD N wg (33, 35, 36, 39, 41)
MD X wg (34)
MD x wg (34, 39–42, 46)
MD m/M 2 (34, 54)
MD ./> 3 (34–36, 48,
MD X wg (34)
MD x wg (34, 39–42, 46)
MD m/M 2 (34, 54)
MD ./> 3 (34–36, 48,
50, 52–59)
MD z wg (39, 41, 44, 45)
MENU +/– 4 (11, 43–60, 65,
MENU +/– 4 (11, 43–60, 65,
68–70)
MENU/NO wf (43–47, 49–60,
62)
NAME EDIT/SELECT r; (48,
62)
Numeric buttons e; (13, 15, 17,
18, 27–32, 34, 48, 61)
@/1 (power) 1
V/v/B/b/ENTER qh
V/v/B/b/ENTER qh
ALPHABETICAL ORDER
A – D
E – N
z
.
>
.
t
y
>
N
X
x
m
M
nN
X
x
N
X
x
O
b
B
V
v
m
M
+
+
–
–
–
wh
wg
wf
wd
ql
qg
qh
qj
qd
qs
qf
6
5
4
1
3
2
7
8
q;
9
wa
qk
w;
ws
qa
z
.
>
.
t
y
>
N
X
x
m
M
nN
X
x
N
X
x
O
b
B
V
v
m
M
+
+
–
–
–
rs
ra
r;
el
ek
eg
ef
wl
wk
wj
ej
eh
e;
ea
es
ed
rd
PLAY MODE/TUNING MODE
0 (12, 14, 15, 33, 35, 41, 47,
60–62)
60–62)
REPEAT/FM MODE 9 (13, 34,
61, 62)
RETURN O qf (18, 27, 30, 31)
SCROLL qk (49, 72)
SLEEP wh (68)
SUBTITLE ed (28)
TAPE nN ws (63–65)
TAPE X ws (63, 65)
TAPE x ws (63–65)
TAPE m/M 6 (63)
TUNER BAND ek (60–62)
TUNER +/– ea (60–62)
TV @/1 wj (10)
TV/VIDEO es (10)
VOL +/– ef
SCROLL qk (49, 72)
SLEEP wh (68)
SUBTITLE ed (28)
TAPE nN ws (63–65)
TAPE X ws (63, 65)
TAPE x ws (63–65)
TAPE m/M 6 (63)
TUNER BAND ek (60–62)
TUNER +/– ea (60–62)
TV @/1 wj (10)
TV/VIDEO es (10)
VOL +/– ef
P – V
BUTTON DESCRIPTIONS
Click on the first or last page to see other HCD-M700 service manuals if exist.