DOWNLOAD Sony HCD-LX10AV / HCD-LX90AV / HCD-LX9AV / LBT-LX10AV / LBT-LX90AV / LBT-LX9AV Service Manual ↓ Size: 10.64 MB | Pages: 81 in PDF or view online for FREE

Model
HCD-LX10AV HCD-LX90AV HCD-LX9AV LBT-LX10AV LBT-LX90AV LBT-LX9AV
Pages
81
Size
10.64 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
hcd-lx10av-hcd-lx90av-hcd-lx9av-lbt-lx10av-lbt-lx9.pdf
Date

Sony HCD-LX10AV / HCD-LX90AV / HCD-LX9AV / LBT-LX10AV / LBT-LX90AV / LBT-LX9AV Service Manual ▷ View online

9
3-3. TAPE MECHANISM DECK (TCM-230PWR1)
Two screws
(BVTP3 
× 8)
Two screws
(BVTP3 
× 8)
Tape mechanism deck
(TCM-230PWR1)
1
 
2
 
3
 
3-4. MAIN BOARD
qs
 Main board 
6
 Back panel
5
 Eleven screws
     (BVTP3
 × 8)
7
 Connector 
     (CN102)
8
 Wire (flat type)
     (19 core) (CN411)
9
 Connector
     (CN412)
qa
 Two connector
     (CN803, CN804)
1
 Wire (flat type) (CN441)
4
 Five screws
     (BVTP3
 × 8)
3
 Two screws
     (BVTP3
 × 8)
0
 Two screws
     (BVTP3
 × 8)
2
 Connector
     (CN903) 
          
LX10AV  Model
10
3-5. CD MECHANISM DECK (CDM37M-5BD32L)
CD mechanism deck
(CDM37M-5BD32L)
9
 Five screws
     (BVTP3
 × 8)
0
 Two screws
     (BVTP3
 × 8)
qs
 Two screws
     (BVTP3
 × 8)
8
 Connector
     (CN412)
7
 Wire (flat type)
     (19 core) (CN411)   
1
 Wire (flat type) (CN441)
5
 Eeven screws
     (BVTP3
 × 8)
4
 Five screws
     (BVTP3
 × 8)
3
 Two screws
     (BVTP3
 × 8)
2
 Connector     
     (CN903) 
qa
 Open the two 
     cable clamps
qd
1
 Five screws
     (BVTP3
 × 8)
2
  
LX10AV Model
6
11
3-6. BASE UNIT (BU-5BD32L)
3
 Base unit
(BU-5BD32L)
1
 BU fitting screw
2
 Boss
3-7. DISC TABLE
Note: When the disc table is installed, adjust the positions of  roller cam
and mark   as shown in the figure, then set to the groove of disc
table.
1
 Two screws (BVTP3 ¥ 8) 
A
2
 Two brackets (BU)
3
 Step screw
4
 Disc table
A
12
SECTION 4
SERVICE MODE
MC Cold Reset
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to
the customer.
Procedure:
1.
Press three buttons  c/CLOCK SET  ,  ENTER  , and  ?/1  simultaneously.
2. “COLD RESET” is displayed on the fluorescent display tube and reset is executed.
CD Delivery Mode
• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1.
Press  ?/1  button to turn the set ON.
2.
Press  LOOP  button and   ?/1  button simultaneously.
3.
A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.
MC Hot Reset
• This mode resets the set with the preset data kept stored in the memory.  The hot reset mode functions same as if the power cord is
plugged in and out.
Procedure:
1.
Press three buttons  c/CLOCK SET  ,  ENTER  , and  DISC 1  simultaneously.
2.
The fluorescent indicator tube becomes blank instantaneously, and the set is reset.
Sled Servo Mode
• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1.
Press  ?/1  button to turn the set ON.
2.
Press three buttons  c/CLOCK SET  ,  ENTER  , and  DISC 5  simultaneously.
3.
The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4.
With the CD in stop status, When the  . AMS >  knob is rotated in the clockwise direction, the pick-up moves outside. When
rotated counterclockwise, it moves inside.
5.
To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Execute MC cold reset. (Press the three buttons  c/CLOCK SET  ,  ENTER  , and  ?/1  button simultaneously.)
Note:
• Always move the pick-up to most inside track when exiting from this mode.  Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.
Change-over of AM Tuner Step between 9kHz and 10kHz (DR8AV Only)
• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1.
Press  ?/1   button to turn the set ON.
2.
Select the function “TUNER”, and press  TUNER/BAND  button to select the BAND “AM”.
3.
Press  ?/1   button to turn the set OFF.
4.
Press  ENTER  and  ?/1  buttons simultaneously, and the display of  fluorescent indicator tube changes to “AM 9k STEP” or “AM 10k
STEP”, and thus the channel step is changed over.
LED and Fluorescent Indicator Tube All Lit, Key Check Mode
Procedure:
1.
Press three buttons  c/CLOCK SET  ,  ENTER  , and  DISC 2  simultaneously.
2.
LEDs and fluorescent indicator tube are all turned on.
Press  DISC 2  button, and the key check mode is activated.
3.
In the key check mode, the fluorescent indicator tube displays “K @ V0 J0”.  Each time a button is pressed, “K”value increases.
However, once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating  . AMS >  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-”
direction.
“V” Value increases like 1, 2, 3 ... if rotating  VOLUME  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
4.
To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
Page of 81
Display

Click on the first or last page to see other HCD-LX10AV / HCD-LX90AV / HCD-LX9AV / LBT-LX10AV / LBT-LX90AV / LBT-LX9AV service manuals if exist.