Sony HCD-LS1 Service Manual ▷ View online
5
SECTION 2
GENERAL
• LOCATION OF CONTROLS
– Front View –
– Front View –
1 FUNCTION button
2 DISC 1 button and indicator
3 DISC 2 button and indicator
4 DISC 3 button and indicator
5 DISC 4 button and indicator
6 DISC 5 button and indicator
7 VOLUME + button
8 TUNER/BAND button
9 u button and indicator
q; x button
qa . m , TUNER - button
qs > M , TUNER + button
qd A button
qf VOLUME - button
1 AM ANTENNA terminals
2 FM ANTENNA jack
3 TAPE OUT jack
4 TAPE IN jack
5 PHONES jack
6 `/1 button
7 PANEL OPEN switch
8 PANEL OPEN/CLOSE switch
1 CD DIGITAL OUT (OPTICAL) connector
2 LEFT SPEAKER terminals
3 RIGHT SPEAKER terminals
– Top View –
– Rear View –
8
9 q; qa qs qd
qf
1
2 3 4 5 6
7
5
4
3
2
1
6
7
8
1
2
3
6
This section is extracted from
instruction manual.
instruction manual.
Step 2: Setting the time
You must set the time before you can use the
timer functions.
timer functions.
The clock is on a 24-hour system for the European
model, and a 12-hour system for other models.
The 24 hour system model is used for illustration
purposes.
model, and a 12-hour system for other models.
The 24 hour system model is used for illustration
purposes.
Set the time before turning on the power.
–
+
–
+
>10
10/0
8
9
7
5
6
4
2
3
1
m
M
–
+
x
.
>
N
X
1
2,3
2,3
1
Press CLOCK/TIMER SET while the
power is off.
power is off.
The hour indication flashes.
2
Press +/– to set the hour then press
ENTER.
ENTER.
The minute indication flashes.
3
Press +/– to set the minute then press
ENTER.
ENTER.
The clock starts.
To change the time
You can change the preset time while the power is
on.
on.
1
Press CLOCK/TIMER SET.
2
Press +/– repeatedly until “SET CLOCK”
appears then press ENTER.
appears then press ENTER.
3
Repeat steps 2 and 3 of “Setting the time”.
Tips
• If you have made a mistake, start again from step 1.
• The built-in clock shows the time in the display
• The built-in clock shows the time in the display
while the power is off.
• The upper dot flashes for the first half of a minute
(0 to 29 seconds), and the lower dot flashes for the
last half of a minute (30 to 59 seconds).
last half of a minute (30 to 59 seconds).
7
SECTION 3
DISASSEMBLY
Note
: Follow the disassembly procedure in the numerical order given.
MAIN CASE SECTION
MECHANISM DECK (HG-1)
6
two claws
7
FFC (26core)
(CN604)
(CN604)
5
two screws
(BTP 3
(BTP 3
×
10)
5
two screws
(BTP 3
(BTP 3
×
10)
9
main case section
4
two screws
(BTP 3
(BTP 3
×
10)
1
screw
(B3
(B3
×
6)
2
bottom cover
3
belt
8
two connectors
(PC501, 502)
(PC501, 502)
5
mechanism deck (HG-1)
2
two lugs
1
four screws
(BTP 3
(BTP 3
×
10)
4
connector
(CP503)
(CP503)
2
two lugs
3
DOOR MOTOR ASS’Y (M391) (Next Page)
HOLDER MECHA, DUST SEAL EMA SL
(Page 9)
HOLDER MECHA, DUST SEAL EMA SL
(Page 9)
8
DOOR MOTOR ASS’Y (M391)
MAIN BOARD
1
connector
(CN391)
(CN391)
5
two screws
(P2.6
(P2.6
×
3)
7
door motor ass’y
(M391)
(M391)
6
motor bracket
2
two screws
(BTP3
(BTP3
×
8)
3
lug
4
1
FFC (15core)
(CN101)
(CN101)
slide knob
4
Remove the MAIN board
in the direction of the arrow.
in the direction of the arrow.
2
five connectors
(CN203, 301, 302, 303, 391)
(CN203, 301, 302, 303, 391)
3
two screws
(PWH2.6
(PWH2.6
×
6)
2
two connectors
(CN201, 204)
(CN201, 204)
Note: On installation MAIN board
adjust the S391 and slide knob.
S391
Click on the first or last page to see other HCD-LS1 service manuals if exist.