Sony HCD-GV10AV Service Manual ▷ View online
2
HCD-GV10AV
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
The following caution label is located inside the unit.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
AM tuner section
Tuning range
Middle Eastern and Philippine models:
Middle Eastern and Philippine models:
531 – 1,602 kHz
(with the interval set at 9
kHz)
(with the interval set at 9
kHz)
Other models:
531 – 1,602 kHz
(with the interval set at 9
kHz)
530 – 1,710 kHz
(with the interval set at 10
kHz)
(with the interval set at 9
kHz)
530 – 1,710 kHz
(with the interval set at 10
kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
120 V, 220 V or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
230 watts
Dimensions (w/h/d)
Approx. 355
×
425
×
450
mm
Mass :
Approx. 16.0 kg
Design and specifications are subject to change
without notice.
without notice.
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50 kHz step)
(50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency
10.7 MHz
3
HCD-GV10AV
TABLE OF CONTENTS
1.
SERVICING NOTES
................................................
4
2.
GENERAL
Location of Controls .......................................................
5
Setting the Time ..............................................................
6
3.
DISASSEMBLY
3-1. Disassembly Flow ...........................................................
7
3-2. Case .................................................................................
7
3-3. Front Panel Section .........................................................
8
3-4. Cover (TC), Tape Mechanism Deck
(TCM-230PWR42) .........................................................
8
3-5. MAIN Board, D.C. Fan (M901) .....................................
9
3-6. CD Mechanism Deck (CDM37L-5BD34L) ................... 10
3-7. Base Unit (BU-5BD34L) ................................................ 11
3-8. Disc Table ........................................................................ 11
3-7. Base Unit (BU-5BD34L) ................................................ 11
3-8. Disc Table ........................................................................ 11
4.
TEST MODE
.............................................................. 12
5.
MECHANICAL ADJUSTMENTS
....................... 14
6.
ELECTRICAL ADJUSTMENTS
Deck section .................................................................... 14
CD Section ...................................................................... 17
Video Section .................................................................. 18
CD Section ...................................................................... 17
Video Section .................................................................. 18
7.
DIAGRAMS
7-1. Block Diagram – CD SERVO Section – ....................... 19
7-2. Block Diagram – AUDIO/VIDEO CD Section – .......... 20
7-3. Block Diagram – TUNER/TAPE DECK Section – ...... 21
7-4. Block Diagram – MAIN Section (1/2) – ....................... 22
7-5. Block Diagram – MAIN Section (2/2) – ....................... 23
7-6. Block Diagram – DISPLAY/KEY CONTROL/
7-2. Block Diagram – AUDIO/VIDEO CD Section – .......... 20
7-3. Block Diagram – TUNER/TAPE DECK Section – ...... 21
7-4. Block Diagram – MAIN Section (1/2) – ....................... 22
7-5. Block Diagram – MAIN Section (2/2) – ....................... 23
7-6. Block Diagram – DISPLAY/KEY CONTROL/
POWER SUPPLY Section – ........................................... 24
7-7. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 25
7-8. Printed Wiring Board – BD Board – ............................. 26
7-9. Schematic Diagram – BD Board – ................................ 27
7-10. Schematic Diagram – VIDEO Board (1/2) – ................ 28
7-11. Schematic Diagram – VIDEO Board (2/2) – ................ 29
7-12. Printed Wiring Board – VIDEO Board – ....................... 30
7-13. Printed Wiring Boards – CD MOTOR Section – .......... 32
7-14. Schematic Diagram – CD MOTOR Section – .............. 33
7-15. Printed Wiring Board – AUDIO Board – ...................... 34
7-16. Schematic Diagram – AUDIO Board – ......................... 35
7-17. Printed Wiring Board – LEAF SW Board – .................. 36
7-18. Schematic Diagram – LEAF SW Board – ..................... 36
7-19. Schematic Diagram – MAIN Board (1/3) – .................. 37
7-20. Schematic Diagram – MAIN Board (2/3) – .................. 38
7-21. Schematic Diagram – MAIN Board (3/3) – .................. 39
7-22. Printed Wiring Board – MAIN Board – ........................ 40
7-23. Printed Wiring Board – PA Board – .............................. 42
7-24. Schematic Diagram – PA Board – ................................. 43
7-25. Printed Wiring Board – SURROUND Board – ............. 44
7-26. Schematic Diagram – SURROUND Board – ................ 45
7-27. Printed Wiring Boards – MIC/FRONT INPUT/
7-9. Schematic Diagram – BD Board – ................................ 27
7-10. Schematic Diagram – VIDEO Board (1/2) – ................ 28
7-11. Schematic Diagram – VIDEO Board (2/2) – ................ 29
7-12. Printed Wiring Board – VIDEO Board – ....................... 30
7-13. Printed Wiring Boards – CD MOTOR Section – .......... 32
7-14. Schematic Diagram – CD MOTOR Section – .............. 33
7-15. Printed Wiring Board – AUDIO Board – ...................... 34
7-16. Schematic Diagram – AUDIO Board – ......................... 35
7-17. Printed Wiring Board – LEAF SW Board – .................. 36
7-18. Schematic Diagram – LEAF SW Board – ..................... 36
7-19. Schematic Diagram – MAIN Board (1/3) – .................. 37
7-20. Schematic Diagram – MAIN Board (2/3) – .................. 38
7-21. Schematic Diagram – MAIN Board (3/3) – .................. 39
7-22. Printed Wiring Board – MAIN Board – ........................ 40
7-23. Printed Wiring Board – PA Board – .............................. 42
7-24. Schematic Diagram – PA Board – ................................. 43
7-25. Printed Wiring Board – SURROUND Board – ............. 44
7-26. Schematic Diagram – SURROUND Board – ................ 45
7-27. Printed Wiring Boards – MIC/FRONT INPUT/
HEADPHONES Boards – ............................................... 46
7-28. Schematic Diagram – MIC/FRONT INPUT/
HEADPHONES Boards – ............................................. 47
7-29. Printed Wiring Board – PANEL FL Board – ................. 48
7-30. Schematic Diagram – PANEL FL Board – ................... 49
7-30. Schematic Diagram – PANEL FL Board – ................... 49
7-31. Printed Wiring Boards
– PANEL VR/ILLUMINATION Boards – ..................... 50
7-32. Schematic Diagram
– PANEL VR/ILLUMINATION Boards – ..................... 51
7-33. Printed Wiring Boards – TC-A/TC-B/CD-L/
CD-R (1)/CD-R (2) Boards – ......................................... 52
7-34. Schematic Diagram – TC-A/TC-B/CD-L/
CD-R (1)/CD-R (2) Boards – ......................................... 53
7-35. Printed Wiring Board – TRANSFORMER Section – ... 54
7-36. Schematic Diagram – TRANSFORMER Section – ...... 54
7-37. IC Pin Function Description ........................................... 61
7-36. Schematic Diagram – TRANSFORMER Section – ...... 54
7-37. IC Pin Function Description ........................................... 61
8.
EXPLODED VIEWS
8-1. Case, Back Panel Section ................................................ 71
8-2. Front Panel Section-1 ...................................................... 72
8-3. Front Panel Section-2 ...................................................... 73
8-4. Chassis Section ............................................................... 74
8-5. CD Mechanism Deck Section (CDM37L-5BD34L) ...... 75
8-6. Base Unit Section (BU-5BD34L) ................................... 76
8-7. Tape Mechanism Deck Section-1
8-2. Front Panel Section-1 ...................................................... 72
8-3. Front Panel Section-2 ...................................................... 73
8-4. Chassis Section ............................................................... 74
8-5. CD Mechanism Deck Section (CDM37L-5BD34L) ...... 75
8-6. Base Unit Section (BU-5BD34L) ................................... 76
8-7. Tape Mechanism Deck Section-1
(TCM-230PWR42) ......................................................... 77
8-8. Tape Mechanism Deck Section-2
(TCM-230PWR42) ......................................................... 78
9.
ELECTRICAL PARTS LIST
............................... 79
4
HCD-GV10AV
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
check that the S curve waveforms is output three times.
SECTION 1
SERVICING NOTES
• MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
MODEL
PART No.
Malaysia and Singapore models
4-232-090-4
[]
Saudi Arabia model
4-232-090-5
[]
Indonesia model
4-232-090-7
[]
SELF-DIAGNOSIS
This unit is equipped with a self-diagnosis function.
The function is used for diagnosing the conditions of the circuits
of the VIDEO board.
The circuits can be determined if normal or abnormal by the light-
ing of D502 of the VIDEO board.
The function is used for diagnosing the conditions of the circuits
of the VIDEO board.
The circuits can be determined if normal or abnormal by the light-
ing of D502 of the VIDEO board.
Lighting of D502
When lit
When lit
: Operates normally
Blinks repeatedly: The circuit may be faulty.
D502
IC505
– VIDEO Board (Side A) –
PART No.
5
HCD-GV10AV
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
LOCATION OF CONTROLS
– Front Panel –
– Front Panel –
ACTIVE wa (22)
A EJECT Z /Z B EJECT wk (25)
AUDIO L jack wd (34)
AUDIO R jack ws (34)
CD FLASH ef (17)
CD LOOP eg (8,17)
CD SYNC qj (26,27)
DIRECT EQUALIZER 6 (29)
A EJECT Z /Z B EJECT wk (25)
AUDIO L jack wd (34)
AUDIO R jack ws (34)
CD FLASH ef (17)
CD LOOP eg (8,17)
CD SYNC qj (26,27)
DIRECT EQUALIZER 6 (29)
SALSA REGGAE
SAMBA TANGO
MOVIE POP
ROCK
SAMBA TANGO
MOVIE POP
ROCK
JAZZ
DANCE GAME
DIRECTION r; (25~27,32)
DISC SKIP w; (12~16,21,27)
DISC 1~5 ea (13,15)
DISPLAY 4 (11,17)
DOLBY NR r; (25,26)
DSP rg (26,29)
DVD5.1CH wh (35)
ECHO LEVEL el (31)
EDIT ed (27)
ENTER e; (23)
ENTER/NEXT qg (11,28,30,33)
FLAT qg (29)
DISC SKIP w; (12~16,21,27)
DISC 1~5 ea (13,15)
DISPLAY 4 (11,17)
DOLBY NR r; (25,26)
DSP rg (26,29)
DVD5.1CH wh (35)
ECHO LEVEL el (31)
EDIT ed (27)
ENTER e; (23)
ENTER/NEXT qg (11,28,30,33)
FLAT qg (29)
FUNCTION qa
(8,15,16,26,27,32,34)
GAME qs (32,34)
GROOVE rf (29)
H SPEED DUB qj (26)
IR receptor 2
Jog dial (AMS./>) ql
GROOVE rf (29)
H SPEED DUB qj (26)
IR receptor 2
Jog dial (AMS./>) ql
(13~17,21,27)
KARAOKE PON/MPX ra (31)
KEY CONTROL 2/# qf (31)
MIC 1 jack ej (31)
MIC 2 jack eh (31)
MIC LEVEL ek (31)
NEXT wa (13,14)
NON STOP es (16)
P.FILE qg (29,30)
PHONES jack qk
PLAY MODE w; (12,15,16,21,27)
POWER SAVE/DEMO
KEY CONTROL 2/# qf (31)
MIC 1 jack ej (31)
MIC 2 jack eh (31)
MIC LEVEL ek (31)
NEXT wa (13,14)
NON STOP es (16)
P.FILE qg (29,30)
PHONES jack qk
PLAY MODE w; (12,15,16,21,27)
POWER SAVE/DEMO
(STANDBY) 3 (11)
PREV wa (13,14)
PRO LOGIC wh (10,30)
PUSH OPEN wj (12,13,15)
REPEAT w; (13,15)
RETURN wa (14)
SELECT wa (14)
PRO LOGIC wh (10,30)
PUSH OPEN wj (12,13,15)
REPEAT w; (13,15)
RETURN wa (14)
SELECT wa (14)
SLEEP 8 (32)
SPECTRUM ANALYZER 5 (31)
STEREO/MONO wg (24)
SUPER WOOFER rd (29,35)
SUPER WOOFER MODE rs (29)
TIMER SELECT 9 (28,33)
TUNER/BAND wl (23,24,26)
TUNER MEMORY e; (23)
TUNING MODE wg (23,24)
VIDEO jack wf (34)
VOLUME control qd (24)
SPECTRUM ANALYZER 5 (31)
STEREO/MONO wg (24)
SUPER WOOFER rd (29,35)
SUPER WOOFER MODE rs (29)
TIMER SELECT 9 (28,33)
TUNER/BAND wl (23,24,26)
TUNER MEMORY e; (23)
TUNING MODE wg (23,24)
VIDEO jack wf (34)
VOLUME control qd (24)
BUTTON DESCRIPTIONS
@/1 1
c/CLOCK SET 7
v/V/b/B q;
z REC qh
X qhr;
m /M, AMS./>
c/CLOCK SET 7
v/V/b/B q;
z REC qh
X qhr;
m /M, AMS./>
(TAPE A/B) qhr;
h/H qhr;
x qhw;r;
m /M (CD/VCD) w;
HX w;
+/– wl
x qhw;r;
m /M (CD/VCD) w;
HX w;
+/– wl
wa
ws
wd
wf
wg
wj
wk
wl
e;
ea
es
ed
ef
eg
ej
el
ek
r;
ra
rs
rd
rf
rg
eh
wh
w;
ql
qd
qs
qa
2 3456789 q;
qf
qg
qh
qj
qk
1