DOWNLOAD Sony HCD-GRX8 / HCD-R800 / HCD-RX88 / HCD-RX99 / MHC-GRX8 / MHC-R800 / MHC-RX88 Service Manual ↓ Size: 9.77 MB | Pages: 99 in PDF or view online for FREE

– 9 –

1

 

Two screws

     (BVTT 2x5)

2

 

Two screws

     (BVTT 2x5)

9

 

Three screws

     (BVTP 2.6x8)

!º

 

Two screws

     (BVTP 2.6x8)

!£

 

Three screws

     (BVTP 2.6x8)

!¡

 

Screw

     (BVTP 2.6x8)

!™

 

Screw

     (BVTP 2.6x8)

!¢

 

Bracket

!∞

 

Mechanism deck

3

 

Small damper

4

 

Small damper

5

 

Push the cassette lids.

6

 

Remove the cassette lids.

7

 

Spring

8

 

Spring

1

 

Ten screws

     (BVTP 2.6x8)

2

 

Three screws

     (BVTP 2.6x8)

!º

 

Four screws

     (BVTP 2.6x8)

!¡

 

Six screws

     (BVTP 2.6x8)

3

 

Panel board

!™

 CONT COM

 board

4

 

Shield

5

 

Flat type wire

     (CN602)

6

 

Konb(Jog)

7

 

Nut

9

 

Nut

8

 

Konb(Volume)

– 10 –

Claw

B

Claw

A

1

 

Turn the cam the

     direction of arrow.

2

 

Pull-out the disc tray.

5

 

Remove the disc tray.

4

 

Two claws

3

 

Flat type wire  (8 core)

Note: When installing the Disc tray, pull around the flat type wire to

pass through the clawA and clawB, as shown in the figure.

(Perfom after removing the front panel.)

– 11 –

• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the

customer.

Procedure:
1. Press three buttons  p  ,  ENTER/NEXT  , and  1/u  simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press  1/u  button to turn the set ON.
2. Press  LOOP  button and  1/u  button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.

• This mode resets the set with the preset data kept stored in the memory.  The hot reset mode functions same as if the power cord is plugged

in and out.

Procedure:
1. Press three buttons  p  ,  ENTER/NEXT  , and  DISC 1  simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons  p  ,  ENTER/NEXT  , and  §  simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, press  ) +  utton move the pick-up to outside track, or  – 0  button to inside track.
5. To exit from this mode, perform as follows:

1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.

Note:
• Always move the pick-up to most inside track when exiting from this mode.  Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press  1/u  button to turn the set ON.
2. Select the function “TUNER”, and press  TUNER/BAND  button to select the BAND “AM”.
3. Press  1/u  button to turn the set OFF.
4. Press  ENTER/NEXT  and  1/u  buttons simultaneously, and the display of  fluorescent indicator tube changes to “AM 9k STEP” or “AM

10k STEP”, and thus the channel step is changed over.

Procedure:
1. Press three buttons  p  ,  ENTER/NEXT  , and  DISC 2  simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.

Press  DISC 2  button, and the key check mode is activated.

3. In the key check mode, the fluorescent indicator tube displays “K 1 V0 J0”.  Each time a button is pressed, “K”value increases. However,

once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating  VOLUME  knob in “+”  direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.

4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.

– 12 –

This mode can be used for checking the operations of the CD player and tape deck.
• When problems occur;

Aging stops, and the stopped state is displayed on the fluorescent display tube.

• When no problems;

Aging continues.

Preparations:
• Set the CD on the DISC1 tray.
• Insert a commercially available tape for recording (tapes which contents can be erased, etc.) in decks A and B.

Press the  p  button,  ENTER/NEXT  button, and  DISC SKIP/EX-CHANGE  button together.
When the aging mode is set, the CD roulette mark blinks. To exit the mode, press the  1/u  button and turn OFF the power.

The aging mode is executed in the following sequence.
If the function is set to “CD” when the aging mode is set, aging is performed starting from the CD player. When set to “TAPE A” or “TAPE
B”, aging is started from deck A.
If the function is set to others, aging will not be started until the function is switched to CD or TAPE.

• The aging status is displayed on the fluorescent display tube.
• Normally, the CD player displays the remaining aging time. But if operations ended abnormally, it displays the cause.
• During the aging of the tape deck, the operations performed will be displayed. If operations ended abnormally, this will be displayed at the

fluorescent display tube.

• During normal operations:

Display of fluorescent display tube

**1-@@

**: Displays “CD” and the remaining aging time (minutes) alternately. The remaining aging time is counted down from 12.

@@: Track number being accessed.

Display

Main Cause

NO DISC ERR

FOCUS1 ERR

FOCUS2 ERR

GFS ERR

FBIAS ERR

SENSOR ERR

TABLE ERR

TRAY ERR

DISC 1 is NO DISC from the beginning

Focus is not imposed properly

The focus deviated several times after the disc rotated normally

GFS ERROR

Error during focus bias adjustment

DISC 1 was found to be NO DISC by the disc sensor

The table did not rotate normally

The tray containing the BD did not operate normally

Aging of CD player (12 minutes)

Aging of deck A

Aging of deck B

Maximum about 12 minutes