Sony HCD-GPX6 / HCD-GPX7 Service Manual ▷ View online
HCD-GPX6/GPX7
17
3-17. CLOSE LEVER
1
washer (3-1-0.4)
2
SPR-E lever close
4
shaft disc stop
5
close lever
3
claw
3-18. (LEVER DIR), GEAR (IDL-B)
4
pulley (gear)
3
nylon washer 1.7
2
claw
washer
0
lever (DIR)
6
gear (IDL-A)
qa
gear (IDL-B)
1
DIR SPR-E
9
stoper
7
Loosen the screw.
8
Hold the release lever
and change the direction.
5
gear (cap)
HCD-GPX6/GPX7
18
6
claw
1
gear (IDL-F)
5
gear loading lever
2
two claws
4
three hooks
3
gear (IDL-D)
7
gear (IDL-C)
3-19. GEAR (IDL-C)
19
HCD-GPX6/GPX7
SECTION 4
TEST MODE
[MC COLD RESET]
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the
I
/
1
button to turn the power
on.
2. Press three buttons of
I
/
1
,
x
(CD), and
[DSGX]
simulta-
neously.
3. The set is reset, and become standby status.
[COMMON TEST MODE]
Enter The Common Test Mode
Procedure:
1. In the standby status, press the
1. In the standby status, press the
I
/
1
button to turn the power
on.
2. Press three buttons of
[REPEAT]
,
x
(TAPE), and
[DSGX]
simultaneously.
3. When the common test mode is activated, “SLEEP” and
“PLAY” icons are blink on the fluorescent indicator tube.
AMP Test
Procedure:
1. In the common test mode, if turn the
1. In the common test mode, if turn the
[VOLUME]
knob clock-
wise, it displays “VOL MAX”, and if turn the knob counter-
clockwise, it displays “VOL MIN”.
clockwise, it displays “VOL MIN”.
2. If the
[TREBLE]
knobs are turned clockwise or counterclock-
wise, it displays “TONE FLAT”.
3. If the
[BASS]
knobs are turned clockwise, it displays “TONE
MAX”, and if turn the knob counterclockwise, it displays
“TONE MIN”.
“TONE MIN”.
4. To release from this mode, disconnect the AC plug to turn the
power off.
Tape Test
Procedure:
1. In the common test mode, insert a tape.
2. Input any audio signal from the
1. In the common test mode, insert a tape.
2. Input any audio signal from the
[VIDEO/MD]
jack (J301) on
the MAIN board.
3. Press the
[ REC]
button, and press the
[ TAPE]
button
to select the tape direction.
4. Press the
[ REC]
button again to start recording.
5. If press the
m
(TAPE) or
M
(TAPE) button, the tape is
returned to recording start point by cue or review operation,
and starts playback.
and starts playback.
6. To release from this mode, disconnect the AC plug to turn the
power off.
[PANEL TEST MODE]
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the
1. In the standby status, press the
I
/
1
button to turn the power
on.
2. Press three buttons of
[PLAY MODE]
,
x
(TAPE), and
[DSGX]
simultaneously.
3. When the panel test mode is activated, LEDs and segments of
fluorescent indicator tube are all turned on.
Version Check
Procedure:
1. In the panel test mode (all LEDs and segments of fluorescent
1. In the panel test mode (all LEDs and segments of fluorescent
indicator tube are turned on), press the
[TUNING MODE]
but-
ton.
2. Destination indication and model type indication are displayed
on the fluorescent indicator tube alternately.
3. From this status, each time the
[TUNING MODE]
button is
pressed, it changes the version display of each module cycli-
cally as follows.
cally as follows.
Display
Module
MC
Main controller
GC
Display
CD
CD system
CDD
CD device master
CDMA
CDM upper module
CDMB
CDM lower module
BDA
BD upper module
BDB
BD lower module
ST
Tuner
TA
Amplifier
TM
Timer
TC
Tape
4. To date of any module, press the
[DSGX]
button.
5. To release from this mode, press three buttons of
[PLAY
MODE]
,
x
(TAPE), and
[DSGX]
simultaneously.
Key Check
Procedure:
1. In the panel test mode (all LEDs and segments of fluorescent
1. In the panel test mode (all LEDs and segments of fluorescent
indicator tube are turned on), press the
[PLAY MODE]
button.
2. It displays “K 0 J0 V0” on the fluorescent indicator tube.
3. Each time a button is pressed, “K” value increases. However,
3. Each time a button is pressed, “K” value increases. However,
once a button is pressed, it is no longer taken into account.
All keys are pressed, display becomes “K26”.
All keys are pressed, display becomes “K26”.
4. “V” value increases like 1, 2, 3 ... if turn the
[VOLUME]
knob
clockwise, or it decreases like 0, 9, 8 ... if turn the knob coun-
terclockwise.
“J” value increases like 1, 2, 3 ... if turn the
terclockwise.
“J” value increases like 1, 2, 3 ... if turn the
[BASS]
or
[TREBLE]
knob clockwise, or it decreases like 0, 9, 8 ... if
turn the knob counterclockwise.
5. To release from this mode, press three buttons of
[PLAY
MODE]
,
x
(TAPE), and
[DSGX]
simultaneously.
z
nN
z
20
HCD-GPX6/GPX7
[CD REPEAT 5 LIMIT CANCEL MODE]
Number of repeat for CD playback is 5 times when the repeat
mode is “REPEAT”. This mode enables CD to repeat playback for
limitless times.
Procedure:
1. Press the
mode is “REPEAT”. This mode enables CD to repeat playback for
limitless times.
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[FUNCTION]
button to select CD function.
3. Press three buttons of . m (CD), x (TAPE), and
[DSGX]
simultaneously.
4. It enters the CD repeat 5 limit cancel mode and display “LIMIT
OFF”
5. To release this mode, press the
I
/
1
button to turn the power
off.
[CD SHIP MODE]
This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the
for instance, when cleaning the optical pick-up.
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[FUNCTION]
button to select CD function.
3. Press three buttons of
[TUNING MODE]
, x (CD),
and
I
/
1
simultaneously. *1
4. Set to the CD ship mode. (chucking on)
5. After blink “STANDBY”, “LOCK” is displayed, disconnect
5. After blink “STANDBY”, “LOCK” is displayed, disconnect
the AC plug.
*1) If press three buttons of
*1) If press three buttons of
[DIRECTION]
, u (CD), and
[DSGX]
simultaneously, Activate the CD ship mode and
MC cold reset.
[CD SLOT LOCK]
This mode is for the antitheft of CD disc in shop. (not for trans-
port)
Procedure:
1. Press the
port)
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[FUNCTION]
button to select CD function.
3. Insert a disc.
4. While pressing the x (CD) button, press the A (CD) button
4. While pressing the x (CD) button, press the A (CD) button
for more 5 seconds.
5. The message “LOCKED” is displayed and the disc slot is
locked. (Even if exiting from this mode, the disc slot is still
locked)
locked)
6. If press the A (CD) button to eject the disc, the message
“LOCKED” is displayed and can not eject the disc.
7. To release this lock, while pressing the x (CD) button, press
the A (CD) button for 5 seconds again.
8. The message “UNLOCKED” is displayed and the disc slot is
unlocked.
[CD POWER MANAGE]
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the
state pulls out AC plug, it is held.
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[FUNCTION]
button to select CD function.
3. Press the
I
/
1
button again to turn the power off (standby).
4. While pressing the x (CD) button, press the
I
/
1
button.
5. It turns power on and display “CD POWER”, then display
“ON” or “OFF”.
[CHANGE-OVER THE AM TUNING INTERVAL]
(EXCEPT AEP model)
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[BAND, TUNER]
button to select TUNER (AM) func-
tion.
3. Press the
I
/
1
button again to turn the power off (standby).
4. While pressing the
[TUNING +]
button, press the
I
/
1
button.
5. It turns power on and display “STEP 9kHz” or “STEP 10kHz”,
and thus the tuning interval is changed over.
[MD/VIDEO FUNCTION CHANGE]
Select either VIDEO or MD of the external input.
Procedure:
1. Press the
Procedure:
1. Press the
I
/
1
button to turn the power on.
2. Press the
[FUNCTION]
button to select MD or VIDEO func-
tion.
3. Press the
I
/
1
button again to turn the power off (standby).
4. While pressing the
[FUNCTION]
button, press the
I
/
1
but-
ton.
5. The another function of the previous function is selected and
display “MD” or “VIDEO”.
Click on the first or last page to see other HCD-GPX6 / HCD-GPX7 service manuals if exist.