Sony HCD-GPX3G Service Manual ▷ View online
HCD-GPX3G
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
• Abbreviation
AR :
AR :
Argentina
model
E2
: 120V AC area in E model
E51
: Chilean and Peruvian models
MX
: Mexican model
Model
Part No.
HCD-GPX3G: E2, E51, AR
4-411-594-0[]
HCD-GPX3G: MX
4-411-594-1[]
MODEL IDENTIFICATION
– Model Number Lavel –
– Model Number Lavel –
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press
1. Press
[I/
1
STANDBY] button to turn the power on.
2. Press the [CD/DISC SKIP] button to select CD function.
3. While pressing the [
3. While pressing the [
x
] button, press the [ENTER] button for
more 5 seconds).
4. The message “UNLOCKED” is displayed and the disc tray is
unlocked.
Note: When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the [?/1 STANDBY] button.
ANTENNA
FM/AM
AUDIO
IN
L
TV/
DVD/
SAT
PC/
GAME
FRONT SPEAKERS
R
L
IMPEDANCE
USE 4
R
Parts No.
Ver. 1.4
Note : Refer to SUPPLEMENT-1 for adding SERVICING
NOTES
NOTES
(TROUBLESHOOTING)
HCD-GPX3G
5
SERVICE POSITION OF CDM76
SERVICE POSITION OF BOARDS
BD76 board
stand
stand
USB board
PANEL board
2CH DAMP board
REGULATOR, SWITCHING board
HCD-GPX3G
6
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
pin
bracket
Pull the tray by the hand.
HCD-GPX3G
7
CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION
:
C1431
&
&
:
&+'$03ERDUG
LQFKHFNLQJWKH&+'$03ERDUGPDNHDFDSDFLWRU
GLVFKDUJHRI&DQG&IRUHOHFWULFDOVKRFN
SUHYHQWLRQ
GLVFKDUJHRI&DQG&IRUHOHFWULFDOVKRFN
SUHYHQWLRQ
LQFKHFNLQJWKH5(*8/$7256:,7&+,1*ERDUGPDNHDFDSDFLWRU
GLVFKDUJHRI&IRUHOHFWULFDOVKRFNSUHYHQWLRQ
GLVFKDUJHRI&IRUHOHFWULFDOVKRFNSUHYHQWLRQ
5(*8/$725
6:,7&+,1*ERDUG
6:,7&+,1*ERDUG
: