Sony HCD-GNX600 / MHC-GNX600 Service Manual ▷ View online
6
HCD-GNX600
This section is extracted
from instruction manual.
from instruction manual.
Remote control
ALBUM + qf
ALBUM – qh
CD wf
CLEAR qk
CLOCK/TIMER SELECT 2
CLOCK/TIMER SET 4
DISC SKIP qd
DISPLAY wh
ENTER qs
EQ qj
ALBUM – qh
CD wf
CLEAR qk
CLOCK/TIMER SELECT 2
CLOCK/TIMER SET 4
DISC SKIP qd
DISPLAY wh
ENTER qs
EQ qj
FM MODE 6
FUNCTION 8
FUNCTION 8
PLAY MODE 5
REPEAT 6
SLEEP 1
REPEAT 6
SLEEP 1
TAPE wd
TUNER/BAND 7
TUNER MEMORY wg
TUNING MODE 5
VOLUME +/– qg
TUNER/BAND 7
TUNER MEMORY wg
TUNING MODE 5
VOLUME +/– qg
The + button has a tactile dot.*
?/1 (power) 3
x (stop) qa
x (stop) qa
29, 31)
X (pause) ql
N (play) w;
–. (go backward) ws
>+ (go forward) wa
N (play) w;
–. (go backward) ws
>+ (go forward) wa
m (rewind) q;
M (fast forward) 9
M (fast forward) 9
* Use the tactile dot as a reference
when operating the system.
ALPHABETICAL ORDER
A – E
F – Z
SYMBOLS
7
5
q;
qg
qh
qj
qk
w;
ws
wd
wg
wh
qf
qd
qs
qa
9
8
6
4
3
1
2
ql
wa
wf
Use buttons on the remote for the operation.
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET.
“CLOCK” appears in the display. Then, the
hour indication flashes in the display.
hour indication flashes in the display.
3
Press –
.
or
>
+
repeatedly to set
the hour.
4
Press ENTER.
The minute indication flashes in the
display.
display.
5
Press –
.
or
>
+ repeatedly to set
the minute.
6
Press ENTER.
The clock starts functioning.
To adjust the clock
1
Press CLOCK/TIMER SET.
“SET” appears in the display, then “PLAY
SET” flashes in the display.
“SET” appears in the display, then “PLAY
SET” flashes in the display.
2
Press –
.
or
>
+ repeatedly to select
“CLOCK SET”, then press ENTER.
The hour indication flashes in the display.
The hour indication flashes in the display.
3
Do the same procedures as step 3 to 6
above.
above.
Notes
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
You cannot set the clock in Power Saving Mode
Setting the clock
7
HCD-GNX600
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2.
SIDE CASE, TOP CASE
(Page 8)
3-3.
LOADING PANEL
(Page 8)
3-4.FRONT PANEL ASSY
(Page 9)
3-5.TUNER PACK
(Page 9)
3-10.
MAIN BOARD,
ADC BOARD
(Page 12)
3-8.CD MECHANISM DECK
(Page 11)
3-7.PANEL BOARD,
IR BOARD,
VOL BOARD
(Page 10)
3-6.TAPE MECHANISM DECK,
MIC BOARD
(Page 10)
3-13.DRIVER BOARD,
SW BOARD
(Page 13)
3-11.POWER BOARD,
SPEAKER BOARD
(Page 12)
3-16.MOTOR (TB) BOARD
(Page 15)
3-17.MOTOR (LD) BOARD
(Page 15)
3-15.SENSOR BOARD
(Page 14)
3-12.SMASTER BOARD,
(Page 13)
3-9.BACK PANEL,
DC FAN (M981)
(Page 11)
3-14.CD BOARD,
OPTICAL PIC-UP
(Page 14)
SET
8
HCD-GNX600
Note:
Follow the disassembly procedure in the numerical order given.
3-2. SIDE CASE, TOP CASE
3-3. LOADING PANEL
2
screw
(case 3 TP2)
(3
(3
×
12)
1
screw (case 3 TP2)
(3
×
8)
4
9
qd
3
screw
(+BVTP 3
×
8)
5
case (side-R)
6
screw
(case 3 TP2)
(3
(3
×
8)
7
screw
(case 3 TP2)
(3
(3
×
12)
8
screw
(+BVTP 3
×
8)
0
case (side-L)
qs
two screws
(+BVTP 3
×
8)
qa
two tapping screws
qf
case (top)
CD mechanism deck (CDM74KFS-F1BD81A)
1
Turn the pulley to the arrow direction.
Front side
Pulley
2
Pull out disc tray.
3
4
loading panel
9
HCD-GNX600
3-4. FRONT PANEL ASSY
3-5. TUNER PACK
1
two screws
(+BVTT 3
×
6)
2
wire (flat type)
(CN1)
3
tuner pack
1
four screws
(+BVTP 3
×
8)
2
tapping screw
3
tapping screw
4
front panel assy
5
wire (flat type)
(CN201)
6
wire (flat type)
(CN509)
7
connector
(CN121)
q;
connector
(CN503)
8
connector
(CN131)
9
connector
(CN205)
Click on the first or last page to see other HCD-GNX600 / MHC-GNX600 service manuals if exist.