Sony HCD-GN1200D / MHC-GN1200D Service Manual ▷ View online
HCD-GN1200D
21
[EMERGENCY HISTORY CHECK]
Information of Emergency History.
1. Enter DVD Service Mode.
2. Select “3. Emergency History” by pressing [3] button on the
remote commander. The screen will appear as follows.
Emg.History Check
Laser Hours CD 999h 59min
1. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
2. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45
DVD 999h
59min
Next Next Page Prev Prev Page
0 Return to top Menu
3. You can check the total time when the laser is turned on during
playback of DVD and CD from the above menu. The maxi-
mum time, which can be displayed are 999h 59min.
mum time, which can be displayed are 999h 59min.
4. You can check the error code of latest 10 emergency history
from the above menu. To view the previous or next page of
emergency history, press
emergency history, press
or
on the remote com-
mander. “Error code” consists of the following (a), (b) and
(c).
(c).
(a) Error code
Example of Error code
1. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
The meaning off error code is as follows.
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer Jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Qdata/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer Jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Qdata/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type
(b) Parameter of error code
Example of Error code
1. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
This is the detail of error code.
(c) Time of error code
Example of Error code
1. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
This is the laser time when an error occured.
5. How to clean laser hours
Press
Press
DISPLAY
button and then press [CLEAR] button.
Both CD and DVD data are cleared.
Emg.History Check
Laser Hours CD
0h 0min
1. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
2. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45
DVD 0h 0min
Next Next Page Prev Prev Page
0 Return to top Menu
6. How to clean Emergency History
Press [DVD TOP MENU] button and then press [CLEAR]
button.
button.
The error code for all emergency history would be reset.
Emg.History Check
Laser Hours CD 999h 59min
1. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
2. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
DVD 999h
59min
Next Next Page Prev Prev Page
0 Return to top Menu
7. To return to the Top Menu of Remocon Diagnosis Menu, press
[0] button on the remote commander.
HCD-GN1200D
22
[CLEAR THE INITIALIZE SETUP DATA]
Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.
remote commander.
Emg.History Check
Laser Hours CD 999h 59min
Initialize setup data...
DVD 999h
59min
Next Next Page Prev Prev Page
0 Return to top Menu
[VERSION INFORMATION CHECK]
Information of fi rmware version.
1. Enter DVD service Mode.
2. Select “4. Version Information” by pressing [4] button on the
remote commander. The screen will appears follows.
Version information
Firm (Main) : Ver. xxxxx
Firm (Sub)
: xxxxx
RISC : xxxxx
8032 : xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx
0 Return to top Menu
3. To return to the Top Menu of Remocon Diagnosis Menu, press
[0] button on the remote commander.
[ERROR MESSAGE]
1. GC error message
• Display
Display on fl uorescent indicator tube,
[GC ERR01]
When “GC ERR01” message appears, all LEDs lights up and
set becomes hang.
set becomes hang.
Set does not respond to any main unit keys or remote controller
keys.
keys.
•
What to do
1. Please check the model resistor value and replace with correct
parts.
2. Plug in the set. The error message shall not be appear.
HCD-GN1200D
23
SECTION 5
MECHANICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode
Torque meter
Meter reading
FWD
CQ-102C
2.9m N • m to 6.9m N • m
30 to 70 g • cm
(0.42 – 0.97 oz • inch)
FWD
back tension
back tension
CQ-102C
0.15m N • m to 0.59m N • m
2 to 6 g • cm
(0.03 – 0.08 oz • inch)
REV
CQ-102RC
2.9m N • m to 6.9m N • m
30 to 70 g • cm
(0.42 – 0.97 oz • inch)
REV
back tension
back tension
CQ-102RC
0.15m N • m to 0.59m N • m
2 to 6 g • cm
(0.03 – 0.08 oz • inch)
FF/REW
CQ-201B
4.8m N • m to 16.7m N • m
49 to 170 g • cm
(0.68 – 2.36 oz • inch)
HCD-GN1200D
24
SECTION 6
ELECTRICAL ADJUSTMENTS
[FM Tune Level Check]
Procedure:
1. Turn the power on.
2. Input the following signal from Signal Generator to FM
1. Turn the power on.
2. Input the following signal from Signal Generator to FM
antenna input directly.
* Carrier Freq : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF)
Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You
cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C
signals.
The mark of “TUNED” means “The selected station signal is
received in good condition.”
TUNER SECTION
FM signal generator
OUT (75 7)
SET
DECK SECTION
Tape
Signal
Used for
P-4-A100
10 kHz, –10 dB
Azimuth Adjustment
0 dB=0.775V
1. Demagnetize the record/playback head with a head demagne-
tizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
3. After the adjustments, apply suitable locking compound to the
parts adjusted.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit ad-
justment.)
should be completed before performing recording circuit ad-
justment.)
6. The adjustments should be performed for both L-CH and
RCH.
7. Switches and controls should be set as follows unless other-
wise specifi ed.
• Test Tape
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT
Note:
Perform this adjustments for both decks
Procedure:
1. Mode: Playback
1. Mode: Playback
set
MAIN board
CN510
Pin (L-CH)
Pin (R-CH)
MAIN board
CN510
Pin (GND)
+
–
level meter
test tape
P-4-A100
(10 kHz, –10 dB)
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
Screw
position
L-CH
peak
within
1dB
Output
level
L-CH
peak
R-CH
peak
within
1dB
Screw
position
R-CH
peak
DECK A
DECK B
Click on the first or last page to see other HCD-GN1200D / MHC-GN1200D service manuals if exist.