DOWNLOAD Sony HCD-GN1000D / MHC-GN1000D Service Manual ↓ Size: 6.38 MB | Pages: 106 in PDF or view online for FREE

21

playback of DVD and CD from the above menu. The maximum
time, which can be displayed are 999h 59min.

4. You can check the error code of latest 10 emergency history

from the above menu. To view the previous or next page of
emergency history, press .  or  >  on the remote
commander.  “Error code” consists of the following (a), (b) and
(c).

(a) Error code

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

The meaning off error code is as follows.
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer Jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Qdata/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type

 (b) Parameter of error code

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

This is the detailed contents of error information

 (c) Time of error code

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

This is the laser hours when an error occured.

5. How to clean laser hours

Press 

 DISPLAY

 button and then press [CLEAR] button.

Both CD and DVD data are cleared.

Manual Adjust

1. Track Balance Adjust:

2. Track Gain Adjust:

3. Focus Balance Adjust:

4. Focus Gain Adjust:

5. Eq Boost Adjust:

6. Iop. ED:

7. TRV. Level:

8. S curve(FE) Level:

9. RFL(PI) Level:

0. MIRR Time:

$ 4 

Change Value

[RETURN]

 Return to previous menu

6. Convert data from hexadecimal to decimal using conversion

table.

7.

Please find the label on the rear of the BU (Base Unit).
The default IOP value is written in the label.

8.

Subtract between these two values.

9. If the remainder is smaller than 93 (decimal), then it is OK.

However, if the value is bigger than 93, then the BU (base unit)
is defective and need to be change.

10. Press 

O RETURN

 button on the remote commander to return

to previous menu.

11. Press [0] button on the remote commander to return to the Top

Menu  of Remocon Diagnosis Menu.

12. Press 

?/1

 button to turn off the set.

Information of Emergency History.

1. Enter DVD Service Mode.

2. Select “3. Emergency History” by pressing [3] button on the

remote commander. The screen will appear as follows.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next]

 Next Page 

[Prev]

 Prev Page

[0]

 Return to Top Menu

3. You can check the total time when the laser is turned on during

22

Emg. History Check

Laser Hours

CD

0h

0min

DVD

0h

0min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next]

 Next Page 

[Prev]

 Prev Page

[0]

 Return to Top Menu

6. How to clean Emergency History

Press [DVD TOP MENU] button and then press [CLEAR] button.
All emergency history are cleared.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 00 00 00 00

00 00 00 00

00 00 00 00

00 00 00 00

2. 00 00 00 00

00 00 00 00

00 00 00 00

00 00 00 00

[Next]

 Next Page 

[Prev]

 Prev Page

[0]

Return to top Menu

7. To return to the Top Menu of Remocon Diagnosis Menu, press

[0] button on the remote commander.

Information of firmware version.

1. Enter DVD service Mode.

2. Select “4. Version Information” by pressing [4] button on the

remote commander. The screen will appears follows.

Version information

Firm (Main) : Ver. xxxxx

Firm (Sub) : xxxxx

RISC : xxxxx

8032 : xxxxx

Audio DSP : xxxxx

Servo DSP : xxxxx

[0]

 Return to Top Menu

3. To return to the Top Menu of Remocon Diagnosis Menu, press

[0] button on the remote commander.

Press [DVD MENU] button and then press [CLEAR] button

on the remote commander.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

Initialize setup data...

[Next]

 Next Page 

[Prev]

 Prev Page

[0]

Return to top Menu

23

1. Clean the following parts with a denatured alcohol-moistened

swab:
record/playback heads pinch rollers
erase head

rubber belts

capstan

idlers

2. Demagnetize the record/playback head with a head

demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to

the parts adjusted.

5. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

2.9m N • m to 6.9m N • m

FWD

CQ-102C

30 to 70 g • cm

(0.42 – 0.97 oz • inch)

FWD

0.15m N • m to 0.59m N • m

back tension

CQ-102C

2 to 6 g • cm

(0.03 – 0.08 oz • inch)

 2.9m N • m to 6.9m N • m

REV

CQ-102RC

30 to 70 g • cm

(0.42 – 0.97 oz • inch)

0.15m N • m to 0.59m N • m

REV

CQ-102RC

2 to 6 g • cm

back tension

(0.03 – 0.08 oz • inch)

4.8m N • m to 16.7m N • m

FF/REW

CQ-201B

49 to 170 g • cm

(0.68 – 2.36 oz • inch)

Mode

Torque meter

Meter reading

0 dB=0.775 V

1. Demagnetize the record/playback head with a head

demagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjust.

4. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in

this service manual.  (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)

6. The adjustments should be performed for both L-CH and R-

CH.

7. Switches and controls should be set as follows unless otherwise

specified.

• Test Tape

  Perform this adjustments for both decks

1. Mode:  Playback

P-4-A100

10 kHz, –10 dB

Azimuth Adjustment

set

MAIN board
CN510
Pin 

1

 (L-CH)

Pin 

3

 (R-CH)

MAIN board
CN510
Pin 

2

 (GND)

+
–

level meter

test tape
P-4-A100
(10 kHz, –10 dB)

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

Screw
position

L-CH
peak

within
1dB

Output
level

L-CH
peak

R-CH
peak

within
1dB

Screw
position

R-CH
peak

24

Use the following test disc on test mode.
• CD:

YEDS-18 (PART No. 3-702-101-01)

or

PATD-012 (PART No. 4-225-203-01)

• DVD (SL)
   NTSC

HLX-503 (PART No. J-6090-069-A)

or

HLX-504 (PART No. J-6090-088-A)

   PAL

HLX-506 (PART No. J-6090-077-A)

• DVD (DL)
   NTSC

HLX-501 (PART No. J-6090-071-A)

or

HLX-505 (PART No. J-6090-089-A)

   PAL

HLX-507 (PART No. J-6090-078-A)

1. Connect an oscilloscope to CN105 pin 6  (RFMON) and

CN105 pin 3 (GND) on the DMB15 board.

2. Turn the power on.
3. Set the test disc (DVD: HLX-503 (NTSC) or HLX-504 (PAL),

CD: YEDS-18) on the tray and press  Y  button to playback.

4. Confirm that oscilloscope waveform is clear and check

RFMON signal level is correct or not.

A clear RFMON signal waveform means that the shape “

◊

” can be

clearly distinguished at the center of the waveform.

Checking Location: DMB15 board (Side A)

+
–

CN105 pin 

6

 (RFMON)

CN105 pin 

3

 (GND)

oscilloscope 

DMB15 board

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

RFMON signal waveform

level: 0.58 to 1.23 Vp-p (DVDSL)

          0.57 to 1.1 Vp-p (CD)

IC102

IC101

IC104

IC201

CN105

CN106

CN105 pin 

3

 (GND)

CN105 pin 

6

 (RFMON)

1

6

3. Mode:  Playback

4. After the adjustments, apply suitable locking compound to

the pats adjusted.

Adjustment Location:  Playback Head (Deck A).

Record/Playback/Erase Head (Deck B).

set

MAIN
board
CN510

test tape
P-4-A100
(10 kHz, –10 dB)

pin 

3

oscilloscope

L-CH

R-CH

V

H

waveform of oscilloscope

in phase 45

°

90

°

135

°

180

°

good

wrong

pin 

2

pin 

1

L

R

When the BASE UNIT is replaced, perform the IOP measurement

(Refer to page 20 of the TEST MODE).

forward

reverse