Sony HCD-FX350I Service Manual ▷ View online
HCD-FX350i
7
2-6. MODULE (DAB TUNER) BLOCK, MAIN BOARD
2-5. KNOB
(VOL)
Note: This illustration sees the front panel block from PANEL board side.
3 connector
(CN904)
1 connector (CN901)
0 MAIN board
4 two screws (BV3)
6 screw
(BVTP3
u 8)
2 connector
(CN902)
5
9 module (DAB tuner) block
7 wire
8
2 knob (VOL)
hole
1 Push the knob (VOL)
by flat-head screwdriver.
front panel block
PANEL board
HCD-FX350i
8
2-7. BASE UNIT
Note 1: This illustration sees the top panel block from base unit side.
1 four floating screws
(PTPWH
M2.6)
3 two vibration proof rubbers
(red)
4 two vibration proof rubbers (green)
6 cover (D1)
7 base unit
2
5 four claws
Note
2: Four claws might be fixed by bond.
Please fix four claws by the bond when
you replace the cover (D1).
2-8. OPTICAL PICK-UP BLOCK (DA11MMVGP)
3 wire (flat type) (16 core) (optical pick-up)
1 Remove four solders.
2 Solder the short-land.
4 BD73 board block
7 optical pick-up block
(DA11MMVGP)
5 tapping screw (P2)
6 shaft (support)
Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the wire (flat type) (16 core).
Note 1: When disconnecting the wire (fl at type) (16 core) of optical pick-up block, solder the short-land.
HCD-FX350i
9
SECTION 3
TEST MODE
COLD RESET
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [FUNCTION], [DAB INITIAL SCAN]
and [
?/1
] simultaneously.
3. When “RESET” appears, the set enters standby status.
PANEL TEST MODE
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [ENTER], [FUNCTION] and [
?/1
] si-
multaneously
3. When the panel test mode is activated, segments of the liquid
crystal display are all turned on.
Version Check
Procedure:
1. In the panel test mode (segments of the liquid crystal display
Procedure:
1. In the panel test mode (segments of the liquid crystal display
are all turned on), press the [DAB INITIAL SCAN] button.
2. On the liquid crystal display, date and version are displayed.
3. From this status, press the [DAB] button, and the destination
3. From this status, press the [DAB] button, and the destination
and model name are displayed.
4. To release from this mode, press three button of [ENTER],
[FUNCTION] and [
?/1
] simultaneously .
Key Test Mode
Procedure:
1. In the panel test mode (segments of the liquid crystal display
Procedure:
1. In the panel test mode (segments of the liquid crystal display
are all turned on), press the [
u] button.
2. The message “KEY0 0 0”displayed. Whenever any buttons are
pressed the value is changed.
The message “VOL UP” is displayed when [VOLUME] knob
is turned clockwise, and “VOL DOWN” is displayed when
[VOLUME] knob is turned counterclockwise.
is turned clockwise, and “VOL DOWN” is displayed when
[VOLUME] knob is turned counterclockwise.
3. To release from this mode, press three button of [ENTER],
[FUNCTION] and [
?/1
] simultaneously.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the [
3. Press the [
?/1
] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button on the remote com-
mander, while pressing the [
x
] button, press the [
?/1
] button.
5. It turns power on and display “CD POWER”, then display
“ON” or “OFF”.
CD SERVICE MODE
This mode can move the SLED of the optical pick-up, and also can
turn the optical pick-up laser power on and off.
Procedure:
1. Press the [
This mode can move the SLED of the optical pick-up, and also can
turn the optical pick-up laser power on and off.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [DSGX], [TUNE +
3. Press three buttons of [DSGX], [TUNE +
M L] and [
?/1
]
simultaneously.
4. It enters the CD service mode and displays “SERVICE”.
5. To exit from this mode, press three buttons of [DSGX],
[TUNE +
5. To exit from this mode, press three buttons of [DSGX],
[TUNE +
M L] and [
?/1
] simultaneously.
Key Operation:
[TUNE +
[TUNE +
M L], [– TUNE l m]:
Use these keys to move the SLED.
When [TUNE +
M L] is pressed in this mode,
the SLED moves to outer circumference and the
message “SLED OUT” is displayed.
message “SLED OUT” is displayed.
When
[–
TUNE
l m] is pressed in this mode,
the SLED moves to inner circumference and the
message “SLED IN” is displayed.
message “SLED IN” is displayed.
[FUNCTION]:
Use this key to turn the optical pick-up laser power
on and off. When the laser power is turned on, the
message “LD ON” is displayed. When the laser
power is turned off, the message “LD OFF” is dis-
played.
on and off. When the laser power is turned on, the
message “LD ON” is displayed. When the laser
power is turned off, the message “LD OFF” is dis-
played.
HCD-FX350i
10
CD FACTORY MODE
Note 1: Do not enter the this mode while any other test mode is in prog-
ress.
Note 2: Do not enter any other test mode while the this mode is in prog-
ress.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function
3. Press three buttons of [DSGX], [DAB] and [
3. Press three buttons of [DSGX], [DAB] and [
?/1
] simultane-
ously.
4. It enters the CD factory mode and the message “FACTORY” is
displayed. When the [DSGX] button is pressed four times, the
following message (initial display) is displayed.
following message (initial display) is displayed.
– –X 1ON
S curve mode setting
Tracking servo setting
RF gain setting
Key Operation:
[DSGX]:
[DSGX]:
The display changes in the following order when-
ever the button is pressed.
ever the button is pressed.
(Initial display)
FCSAG
(
: Focus AGC value)
TRKAG
(
: Track AGC value)
RF_AG
(
: RF AGC value)
[ENTER]:
RF gain setting changes whenever the button is
pressed.
pressed.
“– –”: No gain fi xation.
“AL”: Fix to the gain for AL disc.
“RW”: Fix to the gain for RW disc.
[DAB INITIAL SCAN]:
Tracking servo setting changes whenever the but-
ton is pressed.
ton is pressed.
“ON”: Tracking servo ON.
“OFF”: Tracking servo OFF.
[FUNCTION]:
S curve mode setting changes whenever the button
is pressed.
is pressed.
“ ”: S curve mode OFF.
“S”: S curve mode ON.
5. To release from this mode, press three buttons of [DSGX],
[DAB] and [
?/1
] simultaneously.
SECTION 4
ELECTRICAL CHECK
CD SECTION
Note:
1. CD Block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
1. CD Block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
ed.
3. Use an oscilloscope with more than 10 M
Ω impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specifi ed value with the following checks.
5. Check the focus bias check when optical pick-up block is replaced.
FOCUS BIAS CHECK
Procedure:
1. Connect the oscilloscope to CL102 (RFOUT) and CL117
1. Connect the oscilloscope to CL102 (RFOUT) and CL117
(VREF) on the BD73 board.
2. Press the [
?/1
] button to turn the power on, and press the
[FUNCTION] button to select CD function.
3. Set disc (YEDS-18) and press the [
u] button to playback.
4. Confi rm that oscilloscope waveform is as shown in the fi gure
below (eye pattern).
A good eye pattern means that the diamond shape (
◊) in the
center of the waveform can be clearly distinguished.
Checking Location:
+
–
–
BD73 board
oscilloscope
(DC range)
CL102 (RFOUT)
CL117 (VREF)
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.1 ± 0.4 Vp-p
– BD73 Board (Conductor Side) –
IC101
CL102
(RFOUT)
CL117
(VREF)
Click on the first or last page to see other HCD-FX350I service manuals if exist.