Sony HCD-FX350I Service Manual ▷ View online
HCD-FX350i
6
2-3. TOP PANEL BLOCK
Note: This illustration sees the set from rear side.
2-4. FRONT PANEL BLOCK
1 connector
(SW880)
3 connector
(CN914)
7 top panel block
4 claw
4 claw
2 flexible flat cable (15 core) (CN401)
6 three claws
5
qd front panel block
5 lead wire (from IP board)
qa claw
6 lead wire (from PANEL board)
8 lead wire (from
PANEL
board)
4 screw (BV3)
3 flexible flat cable (21 core) (CN912)
1 connector (CN913)
qs
qa claw
0 screw
(BVTP3
u 8)
7 screw (BV3)
9 floating screw (PTPWH M2.6)
2 Lift up the lead pin.
(AEP,
UK)
UK)
(AEP, UK)
(AEP, UK)
Ver. 1.1
HCD-FX350i
7
2-6. MODULE (DAB TUNER) BLOCK, MAIN BOARD
2-5. KNOB
(VOL)
Note: This illustration sees the front panel block from PANEL board side.
3 connector
(CN904)
1 connector (CN901)
0 MAIN board
4 two screws (BV3)
6 screw
(BVTP3
u 8)
2 connector
(CN902)
5
9 module (DAB tuner) block
7 wire
8
2 knob (VOL)
hole
1 Push the knob (VOL)
by flat-head screwdriver.
front panel block
PANEL board
HCD-FX350i
8
2-7. BASE UNIT
Note 1: This illustration sees the top panel block from base unit side.
1 four floating screws
(PTPWH
M2.6)
3 two vibration proof rubbers
(red)
4 two vibration proof rubbers (green)
6 cover (D1)
7 base unit
2
5 four claws
Note
2: Four claws might be fixed by bond.
Please fix four claws by the bond when
you replace the cover (D1).
2-8. OPTICAL PICK-UP BLOCK (DA11MMVGP)
3 wire (flat type) (16 core) (optical pick-up)
1 Remove four solders.
2 Solder the short-land.
4 BD73 board block
7 optical pick-up block
(DA11MMVGP)
5 tapping screw (P2)
6 shaft (support)
Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the wire (flat type) (16 core).
Note 1: When disconnecting the wire (fl at type) (16 core) of optical pick-up block, solder the short-land.
HCD-FX350i
9
SECTION 3
TEST MODE
COLD RESET
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
The cold reset clears all data including preset data stored in the
memory to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [FUNCTION], [DAB INITIAL SCAN]
and [
?/1
] simultaneously.
3. When “RESET” appears, the set enters standby status.
PANEL TEST MODE
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
Enter The Panel Test Mode
Procedure:
1. In the standby status, press the [
?/1
] button to turn the power
on.
2. Press three buttons of [ENTER], [FUNCTION] and [
?/1
] si-
multaneously
3. When the panel test mode is activated, segments of the liquid
crystal display are all turned on.
Version Check
Procedure:
1. In the panel test mode (segments of the liquid crystal display
Procedure:
1. In the panel test mode (segments of the liquid crystal display
are all turned on), press the [DAB INITIAL SCAN] button.
2. On the liquid crystal display, date and version are displayed.
3. From this status, press the [DAB] button, and the destination
3. From this status, press the [DAB] button, and the destination
and model name are displayed.
4. To release from this mode, press three button of [ENTER],
[FUNCTION] and [
?/1
] simultaneously .
Key Test Mode
Procedure:
1. In the panel test mode (segments of the liquid crystal display
Procedure:
1. In the panel test mode (segments of the liquid crystal display
are all turned on), press the [
u] button.
2. The message “KEY0 0 0”displayed. Whenever any buttons are
pressed the value is changed.
The message “VOL UP” is displayed when [VOLUME] knob
is turned clockwise, and “VOL DOWN” is displayed when
[VOLUME] knob is turned counterclockwise.
is turned clockwise, and “VOL DOWN” is displayed when
[VOLUME] knob is turned counterclockwise.
3. To release from this mode, press three button of [ENTER],
[FUNCTION] and [
?/1
] simultaneously.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the [
3. Press the [
?/1
] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button on the remote com-
mander, while pressing the [
x
] button, press the [
?/1
] button.
5. It turns power on and display “CD POWER”, then display
“ON” or “OFF”.
CD SERVICE MODE
This mode can move the SLED of the optical pick-up, and also can
turn the optical pick-up laser power on and off.
Procedure:
1. Press the [
This mode can move the SLED of the optical pick-up, and also can
turn the optical pick-up laser power on and off.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [DSGX], [TUNE +
3. Press three buttons of [DSGX], [TUNE +
M L] and [
?/1
]
simultaneously.
4. It enters the CD service mode and displays “SERVICE”.
5. To exit from this mode, press three buttons of [DSGX],
[TUNE +
5. To exit from this mode, press three buttons of [DSGX],
[TUNE +
M L] and [
?/1
] simultaneously.
Key Operation:
[TUNE +
[TUNE +
M L], [– TUNE l m]:
Use these keys to move the SLED.
When [TUNE +
M L] is pressed in this mode,
the SLED moves to outer circumference and the
message “SLED OUT” is displayed.
message “SLED OUT” is displayed.
When
[–
TUNE
l m] is pressed in this mode,
the SLED moves to inner circumference and the
message “SLED IN” is displayed.
message “SLED IN” is displayed.
[FUNCTION]:
Use this key to turn the optical pick-up laser power
on and off. When the laser power is turned on, the
message “LD ON” is displayed. When the laser
power is turned off, the message “LD OFF” is dis-
played.
on and off. When the laser power is turned on, the
message “LD ON” is displayed. When the laser
power is turned off, the message “LD OFF” is dis-
played.
Click on the first or last page to see other HCD-FX350I service manuals if exist.