Sony HCD-FC7 Service Manual ▷ View online
25
HCD-FC7
4-5. HOW TO INSTALL THE ROTARY ENCODER (S702), GEAR (STOCKER COMMUNICATION)
4-6. HOW TO INSTALL THE STOCKER ASSY
2
five solders
6
two gears
(stocker communication)
(stocker communication)
4
gear
(stocker communication)
(stocker communication)
RELAY board
7
two screws
(PTPWH2.6
×
8)
5
screw
(PTPWH2.6
×
8)
3
screw
(PWH2
×
6)
rotary encoder
(S702)
(S702)
gear
(stocker
communication)
(stocker
communication)
– rear –
1
rotary encoder
(S702)
(S702)
Engage the rotary encoder (S702)
and the gear (stocker communication)
as shown below in the figure.
and the gear (stocker communication)
as shown below in the figure.
2
three cams
(stocker U/D)
3
three screws
(PTPWH2.6
×
8)
shaft
shaft
rotary encoder
(S702)
(S702)
Install the stocker assy
fitting three shafts into the
each groove of cam (stocker
U/D) then fix by rotating
the cams in the direction
of arrow.
fitting three shafts into the
each groove of cam (stocker
U/D) then fix by rotating
the cams in the direction
of arrow.
hole
gear
(stocker communication)
(stocker communication)
– rear –
screw
1
Position the hole on the gear
(stocker communication) on the
screw of the rotary encoder (S702).
(stocker communication) on the
screw of the rotary encoder (S702).
To install three cams
(stocker U/D), align each groove
of the cam (stocker U/D)
with each
(stocker U/D), align each groove
of the cam (stocker U/D)
with each
f
mark on the
chassis as shown in the figure.
cam
(stocker U/D)
(stocker U/D)
26
HCD-FC7
SECTION 5
TEST MODE
[Version Display Mode]
* The software version is displayed.
Procedure:
1.
Procedure:
1.
Press three buttons of [FUNCTION], x and A (DISC 1)
simultaneously for two seconds.
simultaneously for two seconds.
2.
The message “VERSION” is displayed. The version display
mode is activated.
mode is activated.
3.
Press the NEXT > button. “IF ***” is displayed.
4.
Each time the NEXT > button is pressed, the display
changes in the order of DVD, AREA, VERSION and IF.
changes in the order of DVD, AREA, VERSION and IF.
5.
To exit from this mode, press the ?/1 button.
[Key Test Mode]
* Button check
Procedure:
1.
Procedure:
1.
Press three buttons of [DISPLAY], [FUNCTION] and A (DISC
2) simultaneously.
2) simultaneously.
2.
The message “KEY NUM 0” is displayed and “0” blinks.
3.
Each time a button is pressed, “KEY NUM 0” value increases.
However, once a button is pressed, it is no longer taken into
account.
However, once a button is pressed, it is no longer taken into
account.
4.
When all buttons are pressed, “KEY NUM 24” appears and
the number blinking is stopped.
the number blinking is stopped.
5.
To exit from this mode, disconnect the power cord.
[Display Test Mode]
Procedure:
1.
1.
Press three buttons of [BAND], [DISPLAY] and A (DISC 3)
simultaneously.
simultaneously.
2.
All segments and LEDs are turned on.
3.
When the NEXT > button is pressed, all LEDs are still
turned on and the display will light up as follows.
turned on and the display will light up as follows.
4.
Press the NEXT > button, all LEDs are turned off and
confirm the display.
confirm the display.
5.
Press the NEXT > button, all segments are turned off.
6.
Every pressing of the NEXT > button turns on each
segments in the same order.
segments in the same order.
7.
To exit from this mode, press the ?/1 button.
[OSD Test Mode]
Procedure:
1.
1.
Press the ?/1 button on the main unit or the ?/1 button on
the remote commander to turn the set on.
the remote commander to turn the set on.
2.
Set the FUNCTION to DVD.
3.
Press three buttons of A (DISC 1) , . PREV and [VOLUME
+] simultaneously.
+] simultaneously.
4.
The message “SERVICE IN” is displayed on the display. The
Test Mode Menu is displayed on the TV screen.
Test Mode Menu is displayed on the TV screen.
5.
To execute each function, select the number on the remote
commander.
commander.
6.
See the following section for explanation in detail.
7.
To exit from this mode, press the ?/1 button.
[Disc Slot Lock]
The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1.
disc in the store is equipped.
Setting Procedure:
1.
Turn the set on.
2.
Press two buttons of x and A simultaneously for five
seconds.
seconds.
3.
The message “LOCKED” is displayed and the slot is locked.
Releasing Procedure:
1.
1.
Press two buttons of x and A simultaneously for five seconds
again.
again.
2.
The message “UNLOCKED” is displayed and the slot is
unlocked.
unlocked.
Note : When “LOCKED” is displayed, the slot lock is not released
by turning power on/off with the ?/1 button.
[Repeat Limit Release Mode]
Procedure:
1.
1.
Press three buttons of A (DISC 1) , . PREV and [VOLUME
-] simultaneously.
-] simultaneously.
2.
Repeat limit is released.
[CDM Ship Mode]
* This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
after repair.
Procedure:
1.
1.
Turn the set on.
2.
Set the function to DVD.
3.
Press the x button for five seconds.
4.
The message “MECHA LOCK” is displayed.
5.
Press the ?/1 button to turn off. The CDM ship mode is set.
SACD MULTI
ST NIGHT ALBM
TITLE
SLEEP
TRK
CHAP
INDEX
H TUNED
M MONO
S
kHz BASS SHUF
MHz PBC PROG
MHz PBC PROG
NTSC REP1
DOLBY PLII FMAM
PCMMP3ALL1DISC S
PCMMP3ALL1DISC S
DIGITAL
D
D
dts
SACD MULTI
ST NIGHT ALBM
TITLE
SLEEP
TRK
CHAP
INDEX
H TUNED
M MONO
S
kHz BASS SHUF
MHz PBC PROG
MHz PBC PROG
NTSC REP1
DOLBY PLII FMAM
PCMMP3ALL1DISC S
PCMMP3ALL1DISC S
DIGITAL
D
D
dts
27
HCD-FC7
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[TEST DISC LIST]
Use the following test disc on test mode.
TDV-520CSO (DVD-SL): PART No. J-2501-236-A
LUV-P01 (CD):
TDV-520CSO (DVD-SL): PART No. J-2501-236-A
LUV-P01 (CD):
PART No. 4-999-032-01
TDV-540C (DVD-DL):
PART No. J-2501-235-A
Note:
Do not use exiting test disc for DVD.
[STARTING TEST MODE]
1.
Press the
@/1
button to turn the power on, and set the function
to DVD.
2.
Press three buttons of
Z
(DISC1),
.
PREV and
[VOLUME +]
simultaneously to enter the test mode.
3.
It displays “SERVICE IN” on the fluorescent indicator tube,
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Mecha Error History
6. Version Information
7. Video Level Adjustment
Exit: POWER Key
Model :DAV-FC7
xx
Revision :x.xx
4.
To execute each function, select the desired menu and press its
number on the remote commander (RM-SP900).
number on the remote commander (RM-SP900).
5.
To release from test mode, press the
@/1
button and turn the
power off.
[OPERATING TEST MODE]
0.
SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander operation.
On the Test Mode Menu screen, press
checked from the remote commander operation.
On the Test Mode Menu screen, press
[10/0]
key on the remote
commander, and the following Check Menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. EEPROM
4. GPIO
5. SD Bus
6. Video
0-0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
0-1. All (All items continuous check)
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
• Example display
### Syscon Diagnosis ###
Diag All Check
No.2 Version
2-3. ROM Check Sum
Check Sum = 5498
Press NEXT Key to Continue
Press PREV Key to Repeat
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the
[NEXT ]
button to go to the
next item, or press the
[ PREV]
button to repeat the same
operation again.
To quit the diagnosis and return to Check Menu screen, press the
To quit the diagnosis and return to Check Menu screen, press the
[RETURN]
key on the remote commander to display Check Menu.
• Error occurred
If an error occurred, the diagnosis is suspended and error is displayed.
Press the
Press the
[RETURN]
key on the remote commander to quit the
diagnosis, or press the
[ PREV]
button to repeat the same check
where an error occurred, or press the
[NEXT ]
button to continue
the check from the item next to faulty item.
General Description of Checking Method
Selecting 2 and subsequent items calls the submenu screen of each
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.
Check Items List:
0-2.
Version
0-2-1. All
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-3.
EEPROM Check
0-3-1. Sampling Check
0-3-2. Detail Check
0-3-2. Detail Check
0-4.
GP I/O Check
0-5.
SD Bus Check
0-6.
Video Check
0-2. Version
0-2-2. Revision
The revision number of ROM (IC205) that the program for
the DVD system processor (IC206) is stored.
the DVD system processor (IC206) is stored.
0-2-3. ROM Check Sum
Check sum is calculated. (4 digits hexadecimal number)
>
.
>
.
28
HCD-FC7
0-2-4. Model Type
Model name is displayed. (DAV-FC7)
0-2-5. Region
Model destination code is displayed. (2 digits number)
0-3. EEPROM Check
0-3-1. Sampling Check
EEPROM check at every 64 words.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-3-2. Detail Check
EEPROM check at every 1 word.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-4. GP I/O Check
Pull up/down setting check of the DVD system processor (IC206)
pin 150, 151 and 154 (for clock setting port).
pin 150, 151 and 154 (for clock setting port).
0-5. SD Bus Check
SD bus data check between DVD decoder (IC701) and D-RAM
(IC706).
(IC706).
0-6. Video Check
Output the color bars for video level adjustment.
1.
DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press the
[1]
key on the remote
commander, and the Adjustment Menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
Exit: RETURN
Normally,
[10/0]
is selected to adjust DVD (single layer), CD and
DVD (dual layer) in this order. But, individual items can be adjusted
for the case where adjustment is suspended due to an error. In this
mode, the adjustment can be made easily through the operation
following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment.
for the case where adjustment is suspended due to an error. In this
mode, the adjustment can be made easily through the operation
following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment.
1-0. ALL
Press the
[10/0]
key on the remote commander, and the servo set
data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the
[RETURN]
button on the remote commander.
Note:
During adjustment of each disc, the measurement for disc type judg-
ment is made. As automatic adjustment does not judge the disc
type unlike conventional models, take care not to insert wrong type
discs. Also, do not give a shock during adjustment.
ment is made. As automatic adjustment does not judge the disc
type unlike conventional models, take care not to insert wrong type
discs. Also, do not give a shock during adjustment.
1-1. DVD-SL (single layer)
Press the 1 key on the remote commander and insert a DVD single
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.
DVD Single Layer Disc Adjustment Steps:
1.
Sled tilt reset
2.
Disc check memory SL
3.
Wait 300 msec
4.
Set disc type SL
5.
LD on
6.
Spindle start
7.
Wait 1 sec
8.
Focus servo on 0
9.
Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto LFO adjust
17. Auto focus offset adjust
18. Auto tilt position adjust
19. Auto focus gain adjust
20. Auto focus offset adjust
21. EQ boost adjust
22. Auto loop filter offset adjust
23. Auto track gain adjust
Search Check
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto LFO adjust
17. Auto focus offset adjust
18. Auto tilt position adjust
19. Auto focus gain adjust
20. Auto focus offset adjust
21. EQ boost adjust
22. Auto loop filter offset adjust
23. Auto track gain adjust
Search Check
24. 32 track jump forward
25. 32 track jump reverse
26. 500 track jump forward
27. 500 track jump reverse
25. 32 track jump reverse
26. 500 track jump forward
27. 500 track jump reverse
28.All servo stop
29.EEP copy loop filter offset
29.EEP copy loop filter offset
1-2. CD
Press the
[2]
key on the remote commander and insert a CD disc
following the message. Then the adjustment will be made through
the steps below, then adjusted values will be written to the EEPROM.
the steps below, then adjusted values will be written to the EEPROM.
CD Adjustment Steps
1.
Sled tilt rest
2.
Disc check memory CD
3.
Wait 500 msec
4.
Set disc type CD
5.
LD on
6.
Spindle start
7.
Wait 500 msec
8.
Focus servo on 0
9.
Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. (TC display start)
14. Wait 1 sec
15. Jitter display start
16. Sled ON
17. Check CLV on
18. Auto loop filter offset adjust
19. Auto focus offset adjust
20. Auto focus gain adjust
21. Auto focus offset adjust
22. EQ boost adjust
23. Auto LFO Adjust
11. Wait 500 msec
12. Tracking on
13. (TC display start)
14. Wait 1 sec
15. Jitter display start
16. Sled ON
17. Check CLV on
18. Auto loop filter offset adjust
19. Auto focus offset adjust
20. Auto focus gain adjust
21. Auto focus offset adjust
22. EQ boost adjust
23. Auto LFO Adjust
Click on the first or last page to see other HCD-FC7 service manuals if exist.