Sony HCD-FC7 (serv.man2) Service Manual ▷ View online
21
HCD-FC7
3-18. TIMING BELT (FRONT/REAR)
1
screw
(PTPWH2.6
(PTPWH2.6
×
8)
3
screw
(PTPWH2.6
(PTPWH2.6
×
8)
7
screw
(PTPWH2.6
(PTPWH2.6
×
8)
9
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qa
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qs
cam (gear)
5
screw
(PTPWH2.6
(PTPWH2.6
×
8)
2
pulley
(mode deceleration)
(mode deceleration)
4
gear
(mode 5)
(mode 5)
8
gear (mode 3)
0
gear
(mode 2)
(mode 2)
6
gear (mode 4)
3
slider (mode cam) assy
5
two gears
(center)
(center)
7
two gears (center)
8
timing belt (rear)
timing belt
(rear)
(rear)
When install three timing belts,
its pass under each claws.
its pass under each claws.
9
timing belt (rear)
4
gear
(timing)
(timing)
2
gear (mode cam)
6
timing belt
(front)
(front)
1
screw
(PTPWH2.6
×
8)
timing belt
(rear)
(rear)
timing belt (front)
two claws
two claws
two claws
two claws
3-19. CAM (GEAR)
22
HCD-FC7
3-20. SENSOR BOARD
8
screw
(PTPWH2.6
(PTPWH2.6
×
8)
1
screw
(PTPWH2.6
(PTPWH2.6
×
8)
9
cam
(eject lock)
(eject lock)
qs
gear
(eject lock)
(eject lock)
qd
gear
(mode 1)
(mode 1)
qg
two claws
0
screw
(PTPWH2.6
(PTPWH2.6
×
8)
ql
screw
(BVTP2.6
(BVTP2.6
×
8)
3
screw
(BVTP2.6
(BVTP2.6
×
8)
7
shaft
(shutter)
(shutter)
6
compression spring
(shutter)
(shutter)
4
two screws
(BVTP2.6
(BVTP2.6
×
8)
5
base (shutter) block
2
lever shutter (A)
w;
SENSOR board
qf
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qh
rotary encoder
(S771)
(S771)
qj
claw
qk
harness
qa
cam
(BU U/D)
(BU U/D)
23
HCD-FC7
• This set can be assembled in the order shown below.
4-1. HOW TO INSTALL THE CAM (EJECT LOCK)
SECTION 4
ASSEMBLY
mark
cam (BU U/D)
cam (eject lock)
– bottom view • front –
gear (eject lock)
1
Rotate the cam (BU U/D) fully in the direction of arrow.
2
Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
aligning the mark with the center of the gear (eject lock).
4-2. HOW TO INSTALL THE CAM (GEAR)
boss
cam (gear)
mark
cam (BU U/D)
– bottom view • front –
1
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2
Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
and install the cam (gear).
24
HCD-FC7
mark
B
slider (mode cam) assy
shaft
mark
A
mark
D
gear (mode cam)
cam (gear)
mark
C
1
Slide the shaft in the direction of arrow.
2
Align mark
A
on the gear (mode cam) with mark
B
on the slider (mode cam) assy,
then install the gear (mode cam).
3
Check that mark
C
on the gear (mode cam) is in alignment with mark
D
on the cam (gear).
– bottom view • front –
4-3. HOW TO INSTALL THE GEAR (MODE 2)
4-4. HOW TO INSTALL THE GEAR (MODE CAM)
– bottom view • front –
gear
(mode 2)
(mode 2)
rotary encoder
(S771)
(S771)
cam (BU U/D)
mark
projection
chassis
1
Align the mark on the rotary encoder (S771) with the projection of the assy.
2
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3
Install the gear (mode 2).
Click on the first or last page to see other HCD-FC7 (serv.man2) service manuals if exist.