Sony HCD-DZ7T Service Manual ▷ View online
5
HCD-DZ7T
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
disc in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the
x
button and the
A
button simultaneously for five
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the
x
button and the
A
button simultaneously for five
seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note:
When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the ?/1 button.
power on/off with the ?/1 button.
On cleaning discs, disc/lens cleaners
•
Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause the apparatus
to malfunction.
(including wet or spray types). These may cause the apparatus
to malfunction.
IMPORTANT NOTICE
Caution: This system is capable of holding a still video image or
on-screen display image on your television screen indefinitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
on-screen display image on your television screen indefinitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
Attention when transported
Use this mode when returning the set to the customer after repair.
Procedure:
Procedure:
1. Press the
?/1
button to turn the set on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons
3. Remove all discs, and then press two buttons
H
and
?/1
simultaneously.
4. After a message “MECHA LOCK” is displayed on the
fluorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the
?/1
button to turn the set
on.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CD-RWs recorded in the
following formats:
following formats:
– audio CD format
– VIDEO CD format
– MP3 audio tracks, JPEG image files, and DivX video files of
– VIDEO CD format
– MP3 audio tracks, JPEG image files, and DivX video files of
format conforming to ISO 9660 Level 1/Level 2, or its extended
format, Joliet
format, Joliet
The system can play DVD-ROMs/DVD+RWs/DVD-RWs/
DVD+Rs/DVD-Rs recorded in the following formats:
DVD+Rs/DVD-Rs recorded in the following formats:
– MP3 audio tracks, JPEG image files, and DivX video files of
format conforming to UDF (Universal Disc Format)
Example of discs that the system cannot play
The system cannot play the following discs:
•
CD-ROMs/CD-Rs/CD-RWs other than those recorded in the
formats listed on “Note about CDs/DVDs”
formats listed on “Note about CDs/DVDs”
•
CD-ROMs recorded in PHOTO CD format
•
Data part of CD-Extras
•
DVD Audios
•
Super Audio CD
•
DATA DVDs that do not contain MP3 audio tracks, JPEG
image files, or DivX video files
image files, or DivX video files
•
DVD-RAMs
Also, the system cannot play the following discs:
•
A DVD VIDEO with a different region code
•
A disc that has a non-standard shape (e.g., card, heart)
•
A disc with paper or stickers on it
•
A disc that has the adhesive of cellophane tape or a sticker
still left on it
still left on it
“DVD-RW,” “DVD+RW,” “DVD+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
“DVD VIDEO,” and the “CD” logos are trademarks.
Format of
discs
discs
Disc logo
DVD VIDEO
DVD-RW/
DVD-R
DVD-R
DVD+RW/
DVD+R
DVD+R
VIDEO CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
CD-RW/CD-R
(audio data)
(MP3 files)
(JPEG files)
(audio data)
(MP3 files)
(JPEG files)
This System Can Play the
Following Discs
Following Discs
6
HCD-DZ7T
Copyrights
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
This system incorporates with Dolby* Digital and Dolby Pro Logic
(II) adaptive matrix surround decoder and the DTS** Digital
Surround System.
(II) adaptive matrix surround decoder and the DTS** Digital
Surround System.
*
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS” and “DTS Digital Surround” are registered trademarks
of DTS, Inc.
of DTS, Inc.
Notes about CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/
DVD+RW
DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/
DVD+RW cannot be played on this system due to the recording
quality or physical condition of the disc, or the characteristics of
the recording device and authoring software.
The disc will not play if it has not been correctly finalized. For
more information, see the operating instructions for the recording
device.
Note that some playback functions may not work with some
DVD+RWs/DVD+Rs, even if they have been correctly finalized. In
this case, view the disc by normal playback. Also some DATA CDs/
DATA DVDs created in Packet Write format cannot be played.
DVD+RW cannot be played on this system due to the recording
quality or physical condition of the disc, or the characteristics of
the recording device and authoring software.
The disc will not play if it has not been correctly finalized. For
more information, see the operating instructions for the recording
device.
Note that some playback functions may not work with some
DVD+RWs/DVD+Rs, even if they have been correctly finalized. In
this case, view the disc by normal playback. Also some DATA CDs/
DATA DVDs created in Packet Write format cannot be played.
Peel off the seal and so the lever is moved
in the direction of the arrow with the thin rod.
in the direction of the arrow with the thin rod.
How to open the disc table when power switch turns off
Insert a tapering driver into the aperture of the unit bottom, and slide it in the direction of the arrow.
seal
disc tray
7
HCD-DZ7T
Discharge the charged electricity in capacitors to prevent electric shock as follows
When disassembling the machine, be sure to discharge the charged electricity in the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
POWER board
C903: 440 V (EXCEPT MX) / 240 V (MX)
C932, C933, C934, CN904: 30 V
C903: 440 V (EXCEPT MX) / 240 V (MX)
C932, C933, C934, CN904: 30 V
MAIN board
CN3002: 30 V
CN3002: 30 V
Point of capacitor discharge for C932, C933, C934:
Connect to the red and black wire of CN904
Point of capacitor discharge for C903:
Connect to the foot of CN903
800
Ω
/2W
MAIN board service position
Please take the above-mentioned position in the repair of MAIN board.
In that case, it is necessary the following extension cable during CN304 on IO-S-OUT board and CN4302 on MAIN board .
In that case, it is necessary the following extension cable during CN304 on IO-S-OUT board and CN4302 on MAIN board .
jig P/N: J-2501-242-A
(pitch 1.00 mm/11p/length 300 mm)
(pitch 1.00 mm/11p/length 300 mm)
CN304
jig
MAIN board service position
CN4302
•
Abbreviation
MX : Mexican model
MX : Mexican model
Ver. 1.1
8
HCD-DZ7T
Parts that require fixing using adhesive agent
The following parts on the POWER board must be fixed by using the adhesive agent (such as Sony Bond Master) as it is specified by Safety
Regulations. When any part or printed circuit board is replaced during repair work, be sure to confirm that the following capacitors and resistors
are fixed by using the adhesive agent (such as Sony Bond Master) without fail.
Regulations. When any part or printed circuit board is replaced during repair work, be sure to confirm that the following capacitors and resistors
are fixed by using the adhesive agent (such as Sony Bond Master) without fail.
POWER board : • C924 and R927 (refer to below fig.)
• C913 (Push down to C903 side and so fix.)
• C910 and C930 (refer to below fig.)
• EB905 side of C903
• EB905 side of C934
• C964 and C963 (refer to below fig.)
• Space between C933 and C932
• C908 and Q901 (Don’t touch IC901.)
• C910 and C930 (refer to below fig.)
• EB905 side of C903
• EB905 side of C934
• C964 and C963 (refer to below fig.)
• Space between C933 and C932
• C908 and Q901 (Don’t touch IC901.)
OK:more than 3.5mm
NG:less than 3.5mm
OK:more than 8mm
NG:less than 8mm
OK:more than 8mm
NG:less than 8mm
Don't incline C924 to outside.
POWER BOARD
C910
C924
R927
C930
C964
C963
Attention of the direction at replacement
Please defend and install the direction of the below fig in the following parts on the POWER board.
LF902
LF901
R912
R912
POWER BOARD
L931
mark this side
OK
NG
Click on the first or last page to see other HCD-DZ7T service manuals if exist.