DOWNLOAD Sony HCD-DX70 Service Manual ↓ Size: 9.53 MB | Pages: 71 in PDF or view online for FREE

13

[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:

The aging operation stops and display status.

• If no error occurs:

The aging operation continues repeatedly.

1.

Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray.  Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x ,  ENTER ,  and

DISC SKIP/EX-CHANGE  simultaneously.

4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [MC Cold Reset].

3. Aging Mode in CD section
1) Display state
• No error occurs

Note:
[*][*][*][*] :  Number of aging operations

E

** s ## $$ %%
1 2 3 4 5

• When the buttons x ,  ENTER  and  DISC 1  are pressed simultaneously, number of time of the mechanism error and the NO DISC error

can be checked.
Display:

EMC**EDC**

**:

Number of times of error (Maximum three times)

EMC: Mechanism error
EDC: NO DISC error

• When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.

D: No disc error

01: FOCUS ERROR
02: GFS ERROR
03: SETUP ERROR

01: NO DISC judgment without chucking retry
02: NO DISC judgment after chucking retry

Status at the time of NO DISC judgment
(High order digits only)
1:

STOP

2:

SETUP

3:

TOC READ

4:

ACCESS

5:

PLAY BACK

6:

PAUSE

7:

MANUAL SEARCH (PLAY)

8:

MANUAL SEARCH (PAUSE)

AGING[*][*][*][*]

1

 

**

2

 s

3

 

##

4

 

$$

5

 

%%

M: Mechanism error

Don’t care

High order digits only
D: Stopped during closing due to problems other than mechanism.
E: Stopped during opening due to problems other than mechanism.
C: Stopped during chucking due to problems other than mechanism.
F: Stopped during EX-opening due to problems other than mechanism.

Emergency related errors (High order digits only)
1:

Stopped during chuck-up

2:

Stopped during chuck-down

3:

Time out by EX-OPEN

5:

Time out by EX-CLOSE

The error No. 00 indicates the newest error.  As the error No. increases, it means the older error.
When you want to retrieve the error history, press the  PLAY MODE  button in the case of mechanism error.
Or press the  REPEAT  button in the case of NO DISC error.

Display

14

2)  Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1)

The disc tray opens and closes.

(2)

The mechanism accesses DISC 2 and makes an attempt to
read TOC.  However, since there are no discs, a message
“CD2 NO DISC” appears.

(3)

The mechanism accesses DISC 3 and a message “CD3 NO
DISC” appears.

(4)

The disc tray turns to select a disc1.

(5)

A disc is chucked.

(6)

TOC of disc is read.

(7)

The pickup accesses to the track 1, and  playing 2 seconds.

(8)

The pickup accesses to the last track, and playing 2 seconds.

(9)

Every time when an aging operation of step 1 to step 8 is
complete, the display “AGING[*][*][*][*]” value increases
as the number of aging operations is counted up.

(10) Returns to step 1.

3. Aging Mode in Tape Deck section
1) Display state
• No error occurs

Display action now

• Error occurred

Display action last time

2)  Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1) Rewind is executed up to the top of tape A and B.
(2) A tape on FWD side is played for 2 minutes.
(3) FF is executed up to either made for 20 second or the end of

tape.

(4) A tape is reversed, and the tape on REV side is played for 2

minutes.

(5) Rewind is executed up to the top of tape.
(6) Returns to step 2, and repeat steps from 2 to 5.

[Function Change Mode]
* elect either VIDEO or MD of the external FUNCTION input.

Procedure:
1.

Turn on the power.

2.

Press the two buttons  ENTER  and  ?/1  at the same time.
The main power is turned on and the other function of the
previous function is selected and displayed.  “MD” or
“VIDEO”.

NO. Display action

Action contents

Final timing

1

TAPE A AG-1

Rewind the TAPE A, B

The top of tape

2

TAPE A AG-2

FWD play the TAPE A

2 minutes playing

3

TAPE A AG-3

F.F. the TAPE A

20 second FF or the end

of tape

4

TAPE A AG-4

REV play the TAPE A

2 minutes playing

5

TAPE A AG-5

Rewind the TAPE A

The top of tape

6

TAPE B AG-2

FWD play the TAPE B

2 minutes playing

7

TAPE B AG-3

F.F. the TAPE B

20 second FF or the end

of tape

8

TAPE B AG-4

REV play the TAPE B

2 minutes playing

9

TAPE B AG-5

Rewind the TAPE B

The top of tape

15

0 dB=0.775 V

1. Demagnetize the record/playback head with a head

demagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjust.

4. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this

service manual.  (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)

6. The adjustments should be performed for both L-CH and R-

CH.

7. Switches and controls should be set as follows unless otherwise

specified.

• Test Tape

P-4-A100

10 kHz, –10 dB

Azimuth Adjustment

WS-48B

3 kHz, 0 dB

Tape Speed Adjustment

P-4-L300

315 Hz, 0 dB

Level Adjustment

Note:  Perform this adjustments for both decks

Procedure:
1. Mode:  Playback

Precaution
1. Clean the following parts with a denatured alcohol-moistened

swab:

record/playback heads

pinch rollers

erase head

rubber belts

capstan

idlers

2. Demagnetize the record/playback head with a head

demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

main board
CN301
Pin 3 (L-CH)
Pin 1 (R-CH)

main board
CN301
Pin 2 (GND)

3.06 N • m to 6.96 N • m

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • m

2 to 6 g • cm

(0.02 – 0.08 oz • inch)

3.06 N • m to 6.96 N • m

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • m

2 to 6 g • cm

(0.02 – 0.08 oz • inch)

6.96 N • m to 14.02 N • m

71 to 143 g • cm

(0.98 – 1.99 oz • inch)

9.80 N • m

100 g or more

(3.53 oz or more)

9.80 N • m

100 g or more

(3.53 oz or more)

CQ-102C

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

FWD

FWD
back tension

REV

REV
back tension

FF/REW

FWD tension

REV tension

16

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

3. Mode:  Playback

4. After the adjustments, apply suitable locking compound to the

pats adjusted.

Adjustment Location: Playback Head (Deck A).

Record/Playback/Erase Head (Deck B).

Note: Start the Tape Speed adjustment as below after setting to the test

mode.
In the test mode, the tape speed is high during pressing the

 CD SYNC HI-DUB 

 button.

Procedure:
1. Turn the power switch on.
2. Press the x button,  ENTER  button and  DISC 3  button

simultaneously.
(The “TEST MODE” on the fluorescent indicator tube display
while in the test mode.)
To exit from the test mode, press the ?/1 button.

Mode:  Playback

1. Insert the WS-48B into the deck B.
2. Press the gG button on the deck B.
3. Press the  CD SYNC HI-DUB  button in playback mode.

Then at HIGH speed mode.

4. Adjust RV1001 on the LEAF SW board do that frequency

counter reads 6,000 ± 30 Hz.

5. Press the  CD SYNC HI-DUB  button.

Then back to NORMAL speed mode.

6. Adjust RV1002 on the LEAF SW board so that frequency

counter reads 3,000 ± 15 Hz.

Adjustment Location:  LEAF SW board

Procedure:
Mode:  Playback

Deck A is RV302 (L-CH), Deck B is RV303 (L-CH) so that
adjustment within adjustment level as follows.
Adjustment Level:

CN301 PB level:  334.4 to 748.7 mV (–7.3 to  –0.3 dB) level
difference between the channels:  within ±0.5 dB

Adjustment Location:  MAIN board

Sample Volue of Wow and Flutter: 0.3% or less W. RMS

(WS-48B)

pin 1

° 90° 135° 180°

pin 2

pin 3

main board
CN301 (Pin 3 : 

(Pin 1 : 

main board
CN301 (Pin 3 : L-CH)

forward

reverse