DOWNLOAD Sony HCD-DX10 / HCD-RG20 / HCD-RG30T / HCD-RG4SR / MHC-DX10 / MHC-RG20 / MHC-RG30T / MHC-RG4SR Service Manual ↓ Size: 4.84 MB | Pages: 52 in PDF or view online for FREE

3

PARTS No.

This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.

Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

• Keep the temperature of soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

— BACK PANEL —

• Abbreviation

CND : Canadian model
AUS

: Australian model

AR

: Argentina model

SP

: Singapore model

TW

: Taiwan model

MX

: Mexican model

MY

: Malaysia model

E2

: 120V AC Area in E model

E3

: 240V AC Area in E model

E51

: Chilean and Peruvian model

·········································································· 4

································································ 6

···································································· 11

······························· 13

······································································ 15

5-1. Circuit Board Location ················································ 15
5-2. Block Diagrams ··························································· 16

Tuner/CD Section ························································ 16
Main Section ······························································· 17

5-3. Printed Wiring Board   CD Section ····························· 18
5-4. Schematic Diagram   CD Section ································ 19
5-5. Printed Wiring Board   Main Section ·························· 20
5-6. Schematic Diagram   Main Section (1/4) ···················· 21
5-7. Schematic Diagram   Main Section (2/4) ···················· 22
5-8. Schematic Diagram   Main Section (3/4) ···················· 23
5-9. Schematic Diagram   Main Section (4/4) ···················· 24
5-10. Printed Wiring Board   Address Sensor,

Driver Motor Section ··················································· 25

5-11. Printed Wiring Board   Panel Section ·························· 26
5-12. Schematic Diagram   Panel Section ···························· 27
5-13. Printed Wiring Board   Power Section ························ 28
5-14. Printed Wiring Board   Trans Section ·························· 29
5-15. Schematic Diagram   Trans Section ···························· 30
5-16. IC Block Diagrams ······················································ 31
5-17. IC Pin Function Description ········································ 34

6-1. Main Section ······························································· 36
6-2. Front Panel Section ····················································· 37
6-3. Main Board Section ····················································· 38
6-4. CD Mechanism Deck Section ····································· 39

······································· 40

RG20: US, CND models

RG20: AEP, UK models

DX10: E2, E3, E51, TW models

DX10: AUS, AR, MX models

RG30T

RG4SR

DX10: MY, SP models

4-234-701-0s

4-234-701-1s

4-234-701-2s

4-234-701-3s

4-234-701-4s

4-234-701-5s

4-234-701-6s

4

This section is extracted
from instruction manual.

1

2

3

4 5 6

7

8

9

q;

qa

qs

qd

qf

qg

qh

qj

qk

ql

w;

wa

ws

wd

wf

wg

wh

wj

wk

AUDIO jacks wd (19)
CD wk (10 – 12, 15)
CD SYNC qh (15)
Deck A ws (14)
Deck B qs (14 – 16)
DISC 1 – 3 4 (10, 11)
DISC SKIP EX-CHANGE 3

(10, 11)

Disc tray 5 (10)
DISPLAY w; (12)
EFFECT ON/OFF qd

(17)

GAME wg (18 – 20)

?/1 (power) 1
Z OPEN/CLOSE 6
Z (deck B) qa
M (fast forward) qf
. (go back) qj
> (go forward) qj
X (pause) qj
H (play) qj
x (stop) qj
m (rewind) qk
Z (deck A) wa

GAME EQ ql (17, 18, 20)
GROOVE 8 (17)
MOVIE EQ 7 (17)
MUSIC EQ 2 (17)
PHONES jack q;
REC PAUSE/START qg (15)
TAPE A/B wh (14, 15)
TUNER/BAND wj (12, 13, 15)
VIDEO jack wf (19, 20)
VOLUME control 9

5

1 2 3 4

5

6

7

8

9

0

qa

qs

qd

qf

qg

qh

qj

qk

ql

w;

wa

CD ql (10 – 12, 15)
CLEAR w; (11)
CLOCK/TIMER SELECT 2

(16, 19)

CLOCK/TIMER SET 3 (9, 16,

18)

DISPLAY 6 (12)
D.SKIP 7 (10)
ENTER qg (9, 11 – 13, 16, 18,

19)

EQ +/– qf (17)
GAME q; (18 – 20)
GROOVE qd (17)

ON/OFF qh (17)
PLAY MODE wa (10, 11)
PRESET +/– 5 (13)
REPEAT 8 (11)
SLEEP 1 (18)
STEREO/MONO 8 (13)
SURROUND qa (17)
TAPE A/B 9 (14, 15)
TUNER MEMORY qj (12, 13)
TUNER/BAND qk (12, 13)
TUNING +/– 5 (12, 13)
VOL +/– qs

?/1 (power) 4
M (fast forward) 5
. (go back) 5
> (go forward) 5
X (pause) 5
N (play) 5
m (rewind) 5
x (stop) 5

?/1

Proceed to step 5 when “CLOCK” appears
in the display.

.

>

.

>

The minute indication flashes.

.

>

If you made a mistake or want to change the time,
start over from step 2.

The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.

6

 Disassemble the unit in the order as shown below.

 Follow the disassembly procedure in the numerical order given.

4

qa

q;

q;

8

Case (Top)

Case (Side-L)

Case (Side-R)

5

Two screws (Case 3 TP2)

7

Two screws

     (+BVTP 3

 

×

 10)

3

Two screws

     (+BVTP 3

 

×

 10) 

1

Two screws (Case 3 TP2)

9

Four screws (+BVTP 3

 

×

 6)

6

Screw (Case 3 TP2)

2

Screw (Case 3 TP2)