Sony HCD-CX4IP / HCD-CX5IP Service Manual ▷ View online
HCD-CX4iP/CX5iP
9
2-4. CD MECHANISM DECK (CDM80BTK-F4BD94D-V)
3 four screws
(BVTP3
u 8)
1 connector
(CN1210)
2 connector
(CN1100)
6 connector
7 CD mechanism deck
(CDM80BTK-F4BD94D-V)
Insert is straight to the interior.
Insert is incline
flat cable
connector
connector
flat cable
OK
NG
Note: When you install the flat cable, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
5 flexible flat cable (21 core)
(CN301)
4
– Rear bottom view –
:LUHVHWWLQJ
tape
tape
tape
tape
HCD-CX4iP/CX5iP
10
2-5. MAIN BOARD
– Rear side view –
– Front side view –
– Rear side view –
0 two screws
(BVTT3
u 6)
0 screw
(BVTT3
u 6)
qa coating clip (75)
coating clip (75)
qs spacer
(KGSL-2M-V0)
qd claw
qf MAIN board
1 connector
(CN301)
7 connector
(CN471)
9 connector
(CN702)
8 connector
(CN701)
2 connector
(CN690)
3 connector
(CN671)
4 flexible flat cable (7 core)
(CN1161)
AUDIO-JACK board
DC-JACK board
SP board
tuner block
5 Cut the binding
band
(taiton).
binding band (taiton)
6 sleeve ferrite clamp
sleeve ferrite clamp
tape
tape
tape
Note 1: In reassembling, use new binding
band (taiton) to fasten the clamp
same as before.
Note 2: When you install the flat cable, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is straight to the interior.
Insert is incline
flat cable
connector
connector
flat cable
OK
NG
(US, Canadian)
(US, Canadian)
(US, Canadian, Taiwan)
tape
ferrite core
ferrite core
tape
tape
tape
MAIN board
coating clip
:ire settinJ
adhesive
tape (EMC)
tape (EMC)
adhesive tape (EMC)
HCD-CX4iP/CX5iP
11
2-7. BASE UNIT (BU-F4BD94D-V)
2-6. BELT
(MOT)
– CD mechanism deck block bottom view –
1 belt (MOT)
4
– CD mechanism deck block bottom view –
3 three floating screws
(PTPWH
M2.6)
3 floating screw
(PTPWH
M2.6)
1 tension coil spring (G-1)
2 tension coil spring (G-2)
5 vibration proof rubber
5 vibration proof rubber
5 vibration proof rubber
5 vibration proof rubber
6 base unit
(BU-F4BD94D-V)
HCD-CX4iP/CX5iP
12
2-8. OPTICAL PICK-UP (KSM-215CFP)
Note 1: When disconnection the wire (fl at type) (16 core) of optical pick-up, solder the short-land.
2 Solder the short-land.
Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the wire (flat type) (16 core).
1 Remove four solders.
3 wire (flat type) (16 core)
(optical
pick-up)
5 optical pick-up
(KSM-215CFP)
4 BD94D-V board
Click on the first or last page to see other HCD-CX4IP / HCD-CX5IP service manuals if exist.