Sony HCD-CP100 / HCD-CP100K Service Manual ▷ View online
4
HCD-CP100/CP100K
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
• MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
Power Voltage Indication
VOLTAGE SELECTOR
Switch
Switch
Power Voltage
Incdication
AC: 120 V 60 Hz 75 W
AC: 230 V -50/60 Hz 75 W
AC: 110 – 120/
220 – 240 V / 50/60 Hz 75 W
220 V/60 MHz 75 W
Model
US, CND, MX models
AEP, UK models
E, EA, AR, SP, AUS models
KR model
• Abbreviation
AR
: Argentina model.
AUS
: Australian model.
CND : Canadian model.
EA
EA
: Saudi Arabia model.
KR
: Korean model.
MX
: Mexican model.
SP
: Singapore model.
TH
: Thailand model.
SERVICE POSTION
In checking the CD block, prepare jig (extension cable J-2501-
011-B).
011-B).
Connect jig (extension cable J-2501-011-B)
to the MAIN board (CN101) and CD board (CN101).
to the MAIN board (CN101) and CD board (CN101).
MAIN board
CD board
5
HCD-CP100/CP100K
SECTION 2
GENERAL
• LOCATION OF CONTROLS
– Front View –
1 STANDBY I/1 button and indicator
2 Remote sensor
3 BASS knob
4 TREBLE knob
5 DSG button and indicator
6 TAPE REC z button
7 TAPE Y button
8 TAPE EJECT Z button
9 TAPE x button
0 TAPE m / M button
qa TAPE X button
qs CD SYNC button and indicator
qd TUNER BAND button
qf TUNING +/– button
qg TUNING MODE button
qh VOLUME knob
qj CD EJECT Z button
qk CD x button
ql CD . m / M > button
w; REPEAT button
wa PLAY MODE button
ws CD u button
wd PHONES jack
wf FUNCTION knob
– Rear View –
1 AM ANTENNA terminals
2 FM ANTENNA jack or terminals
3 AUDIO IN MD (VIDEO) jacks
4 CD DIGITAL OUT OPTICAL connector
5 SPEAKER terminals
6 VOLTAGE SELECTOR switch
7 AC power cord
A
Z
Y
?/1
x
m
M
z
X
Z
u
x
.
>
m
M
1 2
5
8
9
q;
wf
qd
qf
qg
qj
qk
qa
6
3
4
7
ql
w;
wa
wd
ws
qs
qh
6
7
1
3
4
5
2
6
HCD-CP100/CP100K
This section is extracted from
instruction manual.
instruction manual.
Remote Control
1
2
3
8
5
6
4
9
0
qa
qs
qd
qj
qk
qh
qg
qf
ql
w;
wa
ws
7
Setting the time
1
Turn on the system.
2
Press TIMER SET on the remote.
If you are setting the clock for the first time,
go to step 5.
go to step 5.
3
Press ./> on the remote
repeatedly until “SET CLOCK” appears
in the display.
repeatedly until “SET CLOCK” appears
in the display.
4
Press ENTER on the remote.
The hour indication flashes.
5
Press ./> on the remote
repeatedly to set the hour.
repeatedly to set the hour.
6
Press ENTER on the remote.
The minute indication flashes.
7
Press ./> on the remote
repeatedly to set the minute.
repeatedly to set the minute.
8
Press ENTER on the remote.
The clock will begin operating.
To reset the system clock
Start over from step 1.
1 DSG button
2 DISPLAY button
3 I/1 (power) button
4 X button
5 x button
6 . / > buttons
7 m / M buttons
8 z REC button
9 PLAY MODE button
0 TUNING MODE button
qa VOLUME +/– buttons
qs TIMER SELECT button
qd ENTER button
qf SLEEP button
qg TIMER SET button
qh MEMORY button
qj STEREO/MONO button
qk CD REPEAT button
ql DIR MODE button
w; TAPE Y button
wa TUNER/BAND button
ws CD N button
HCD-CP100/CP100K
7
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. COVER (UPPER)
(Page 8)
Set
3-4. FRONT PANEL SECTION
(Page 9)
3-3. CD LID
(Page 8)
3-5. TAPE MECHANISM DECK
(Page 9)
3-7. BASE UNIT
(BU-K6BD41A)
(Page 10)
3-8. LOADING BOARD
(Page 11)
3-9. CAM (CDM55)
(Page 11)
3-6. CD MECHANISM DECK
(CDM55F-K6BD41A)
(Page 10)