Sony HCD-BX5 / HCD-DX5 / HCD-DX5J / MHC-BX5 / MHC-DX5 / MHC-DX5J Service Manual ▷ View online
5
SECTION 2
GENERAL
1
2 3 4
5
6
7
8
qa
qs
qd
qf
qg
qh
qk
w;
ea
es
wf
wg
wh
wj
wk
wl
9
q;
ql
qj
wa
ws
wd
e;
1
DISC SKIP EX-CHANGE button
2
DISC 1 button and indicator
3
DISC 2 button and indicator
4
DISC 3 button and indicator
5
Z OPEN/CLOSE button
6
EDIT, TUNER MOMERY button
7
PLAY MODE, STEREO/MONO button
8
REPEAT button
9
DIRECTION, PTY knob
q;
SURROUND button
qa
VOLUME knob
qs
PHONE jack
qd
ENTER/NEXT button
qf
REC/PAUSE START button and indicator
qg
CD SYNC HI-DUBB button
qh
LOOP button
qj
V-GROOVE button and indicator
qk
CURSOL button and indicator
ql
GROOVE button
w;
EQ EDIT button
wa
SPECTRUM button
ws
DISPLAY button
wd
?/1 button and indicator
wf
TUNER BAND button
wg
MD (VIDEO) button
wh
Y button
wj
> + button
wk
X button
wl
– . button
e;
x button
ea
TAPE A/B button
es
CD button
Photo: HCD-BX5
6
6
Step 1: Hooking up the system
(continued)
To attach the front speaker pads
Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the
speakers and prevent them from slipping.
Positioning the speakers
(MHC-BX7/DX7 only)
Before you connect them, determine the best
location for your speakers.
1
Place the front speakers at an angle
of 45 degrees from your listening
position.
2
Place the surround speakers facing
each other at about 60 to 90 cm
above your listening position.
E
e
e
E
Front
speaker
(L)
Front
speaker
(R)
Surround
speaker
(L)
Surround
speaker
(R)
45º
Surround
speaker
60 to 90 cm
Inserting two size AA (R6)
batteries into the remote
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates
the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of
time, remove the batteries to avoid possible damage
from battery leakage.
When carrying this system
Do the following to protect the CD
mechanism.
1
Make sure that all discs are removed from
the unit.
2
Hold down CD and then press
?/1
so that
“LOCK” appears in the display.
3
Unplug the AC power cord.
7
1
Press CLOCK/TIMER SET.
The hour indication flashes.
2
Press
.
or
>
repeatedly to set
the hour.
3
Press ENTER.
The minute indication flashes.
4
Press
.
or
>
repeatedly to set
the minute.
5
Press ENTER.
The clock starts working.
Tip
If you’ve made a mistake, start over from step 1.
To change the time
The previous explanation shows you how to set the
time while the power is off. To change the time
while the power is on, do the following:
1
Press CLOCK/TIMER SET.
2
Press
.
or
>
repeatedly to select
SET CLOCK.
3
Press ENTER.
4
Perform steps 2 through 5 above.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
Step 2: Setting the
time
You must set the time before using the timer
functions.
The clock is on a 24-hour system for the
European model and a 12-hour system for
other models.
The 24-hour system model is used for
illustration purposes.
0)
=+
œP
p
(P
p
1
3,5
2,4
This section is extracted from
instruction manual.
instruction manual.
7
SECTION 3
DISASSEMBY
Note :
Follow the disassembly procedure in the numerical order given.
Side panel R
4
q;
8
Upper case (Top)
Side panel L
5
Two screws (Case)
7
Two screws
(+BVTP 3
×
10)
3
Two screws
1
Two screws (Case)
9
Two screws (+BVTP 3
×
10)
6
Screw (Case)
2
Screw (Case)
2
Pull-out the disc tray.
1
Turn the pulley to the direction of arrow.
pulley
Loading panel assy
Front panel side
CD mechanism deck (CDM58)
3
3-1. UPPER CASE (TOP)
3-2. LOADING PANEL ASSY
8
7
8
CD mechanism deck (CDM58)
Front panel section
3
Connector (CN2)
2
Connector (CN1)
1
Flat type wire (CN304)
6
Three screws (+BVTT 3
×
6)
5
Screw (+BVTP 3
×
10)
4
Screw (+BVTP 3
×
10)
6
Tape mechanism deck
5
Five screws (+BVTP 2.6
×
8)
1
Screw (+BVTP 2.6
×
8)
2
Bracket (Heart cam R)
4
Bracket (Heart cam L)
3
Screw (+BVTP 2.6
×
8)
3-3. FRONT PANEL SECTION
3-4. TAPE MECHANISM DECK
Click on the first or last page to see other HCD-BX5 / HCD-DX5 / HCD-DX5J / MHC-BX5 / MHC-DX5 / MHC-DX5J service manuals if exist.