Sony DVP-NS36 / DVP-NS37 / DVP-NS45P / DVP-NS55P / DVP-NS61P / DVP-NS63P / HTP-36DW / HTP-36SS Service Manual ▷ View online
2-2
DVP-NS36/NS37/NS45P/NS55P/NS61P/NS63P
2-3. LOADING ASSEMBLY
a
a
4
Three Screws
+BV3
(3-CR)
5
Loading Assembly
1
FMO-009 Flat Flexible Cable (CN101, 24P)
3
FMS-010 Flat Flexible Cable (CN202, 5P)
2
MD-111 Harness (CN201, 6P)
2-3
DVP-NS36/NS37/NS45P/NS55P/NS61P/NS63P
2-4. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
After take-out FMO-009 Flat Flexible Cable from CN101 of
MV-50/MV-51 board immediately ground FMO-009 Flat
Flexible Cable pattern using short clip. Metal paper clip can be
used as short clip.
MV-50/MV-51 board immediately ground FMO-009 Flat
Flexible Cable pattern using short clip. Metal paper clip can be
used as short clip.
Shortland Position
Note:
Solder shortland before remove the
FMO-009 Flat Flaxible Cable from
24 pin BU connector.
FMO-009 Flat Flaxible Cable from
24 pin BU connector.
5
FMO-009 Flat Flexible Cable (CN101, 24P)
4
MD-111 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-313CAA/C2RP)
2
FFC Holder
2-4
DVP-NS36/NS37/NS45P/NS55P/NS61P/NS63P
2-5. REAR PANEL, MV BOARD and IF BOARD
2-5-1. REAR PANEL, MV-51 and IF-144/IF-145 BOARDS
(DVP-NS45P/NS55P/NS61P/NS63P/NS36:RUS)
4
FMS-010 Flat Flexible Cable
(CN202,
5P)
6
FIM-013 Flat Flexible Cable
(CN404,
17P)
5
FMO-009 Flat Flexible Cable
(CN101,
24P)
7
MV-51 Board
3
MD-111 Harness
(CN201,
6P)
8
PM-127 Harness
(CN501,
10P)
6
Five Screws
+BV3
(3-CR)
1
Three Screws
+BV3
(3-CR)
2
Rear Panel
1
Tapping Screw
q;
IF-144 Board
9
a
a
l
3
FSW-001 Flat Flexible Cable
(CN403,
7P)
0
IF-145 Board
o
l
EXCEPT DVP-NS63P
DVP-NS63P
Note:
Caution Point on the PWB IF-144/IF-145
When handling IF-144/IF-145 PWB avoid
contact with the sharp metal edge on the top side
of Vacuum Fluorescent Display (ND401).
contact with the sharp metal edge on the top side
of Vacuum Fluorescent Display (ND401).
2-5
DVP-NS36/NS37/NS45P/NS55P/NS61P/NS63P
2-6. SWITCHING REGULATOR
2-5-2. REAR PANEL, MV-50 and IF-144 BOARDS
(DVP-NS36:AEP/NS37)
2
Two Screws
+BV3
(3-CR)
1
Connector
(PM-127
Harness,
CN201,
10P)
3
Power Board
4
FMS-010 Flat Flexible Cable
(CN202,
5P)
6
FIM-013 Flat Flexible Cable
(CN404,
17P)
5
FMO-009 Flat Flexible Cable
(CN101,
24P)
7
MV-50 Board
3
MD-111 Harness
(CN201,
6P)
8
PM-127 Harness
(CN501,
10P)
6
Five Screws
+BV3
(3-CR)
1
Three Screws
+BV3
(3-CR)
2
Rear Panel
1
Tapping Screw
a
a
l
3
FSW-001 Flat Flexible Cable
(CN403,
7P)
0
IF-14
4
Board
q;
9
Click on the first or last page to see other DVP-NS36 / DVP-NS37 / DVP-NS45P / DVP-NS55P / DVP-NS61P / DVP-NS63P / HTP-36DW / HTP-36SS service manuals if exist.