Sony DHC-FLX5D / DHC-FLX7D / HCD-FLX5D / HCD-FLX7D Service Manual ▷ View online
HCD-FLX5D/FLX7D
21
• This set can be assembled in the order shown below.
4-1.
ASSEMBLY FLOW
SECTION 4
ASSEMBLY
4-4. STOCKER SECTION INSTALLATION
(Page 22)
4-3. SLIDER (SELECTION) INSTALLATION
(Page 22)
4-2. GEARS INSTALLATION
(Page 21)
4-5. CHASSIS (MOLD B) SECTION
INSTALLATION (Page 23)
1
Slide the slider (u/d)
fully in the arrow
direction.
fully in the arrow
direction.
3
gear (gear B)
2
gear (U/D slider)
4
gear (gear A)
portion A
Adjust the gear (gear B) with the
portion A as shown.
portion A as shown.
slider (U/D) gear
Adjust the gear so that it meshes with
the bottom tooth of slider (U/D) gear,
as shown.
the bottom tooth of slider (U/D) gear,
as shown.
gear
(gear B)
(gear B)
linearly
Adjust so as to be aligned with
gear B linearly, as shown.
gear B linearly, as shown.
4-2.
GEARS INSTALLATION
Note:
Follow the assembly procedure in the numerical order given.
HCD-FLX5D/FLX7D
22
2
portion A of tray (sub)
1
stocker section
3
two step screws
3
two step screws
Hook the portion A of tray (sub)
to the slider (selection).
to the slider (selection).
portion A
of tray (sub)
of tray (sub)
sticking of
slider (selection)
slider (selection)
2
gear (chuking)
6
two screws
(PTPWH M2.6)
(PTPWH M2.6)
5
washer
3
convex portion of
slider (selection)
slider (selection)
4
compression spring
7
Insert the slider (selection)
into the portion A.
1
rotary encoder
rotary encoder
Align with the slot of
rotary encoder.
rotary encoder.
align marking
portion A
gear (chuking)
Insert a convex portion into
a groove of gear (chuking).
a groove of gear (chuking).
4-3.
SLIDER (SELECTION) INSTALLATION
4-4.
STOCKER SECTION INSTALLATION
HCD-FLX5D/FLX7D
23
3
three screws
(BVTP M2.6)
(BVTP M2.6)
2
Insert the gear (eject)
under the gear (LD
deceleration).
under the gear (LD
deceleration).
1
Insert the portion A of
chassis (mold B) section
into the portion B of
slider (selection).
chassis (mold B) section
into the portion B of
slider (selection).
gear (LD deceleration)
portion A
portion B of
slider (selection)
slider (selection)
4-5.
CHASSIS (MOLD B) SECTION INSTALLATION
24
HCD-FLX5D/FLX7D
SECTION 5
TEST MODE
[COLD RESET]
•
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Press three buttons
1. Press three buttons
[ ]
,
[DISPLAY]
, and
[GROOVE]
simulta-
neously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[TUNER STEP CHANGE]
(Except FLX5D: Saudi Arabia/FLX7D: Saudi Arabia models)
•
A step of AM channels can be changed over between 9 kHz and
10 kHz.
10 kHz.
Procedure:
1. Press the
1. Press the
[I/ ]
button to turn the power on.
2. Select the function “TUNER”, and press
[TUNER/BAND]
but-
ton to select the BAND “AM”.
3. Press the
[I/ ]
button to turn the set OFF.
4. Press
M
+ and
[I/ ]
buttons simultaneously, and the display
of fluorescent indicator tube changes to “AM 9 K Step” or “AM
10 K Step”, and thus the channel step is changed over.
10 K Step”, and thus the channel step is changed over.
[FUNCTION CHANGE MODE]
•
Select either VIDEO or MD of the external function input.
Procedure:
1. Press the
1. Press the
[I/ ]
button to turn the power on.
2. Hold down
[VIDEO $SAT%]
button then press
[I/ ]
button, and
release
[I/ ]
button first in order not in switch off the set imme-
diately.
The another function of the previous function is selected, the
input level is also changed and displayed “SAT” or “VIDEO”.
The another function of the previous function is selected, the
input level is also changed and displayed “SAT” or “VIDEO”.
[GC TEST MODE]
•
This mode is used to check the software version, FL tube, LED,
keyboard and VACS.
keyboard and VACS.
Procedure:
1. Press three buttons
1. Press three buttons
[ ]
,
[DISPLAY]
, and
[EFFECT]
simulta-
neously.
2. LEDs and fluorescent indicator tube are all turned on.
3. When you want to enter the software version display mode,
3. When you want to enter the software version display mode,
press
[GROOVE]
. The model number and destination are dis-
played.
4. Each time
[GROOVE]
is pressed, the display changes stating
from MC version, GC version, DP version, DVD version,
CDDM, CDMA, CDMB, BDA, BDB, ST version, TA version,
TM version, TC version, in this order.
CDDM, CDMA, CDMB, BDA, BDB, ST version, TA version,
TM version, TC version, in this order.
5. When
[CD SYNC HI-DUB]
is pressed while the version num-
bers are being displayed except model number and desti-
nation, year, month and day of the software creation ap-
pear. When
nation, year, month and day of the software creation ap-
pear. When
[CD SYNC HI-DUB]
is pressed again, the display
returns to the software version display. When
[GROOVE]
is pressed while year, month and day of the software creation
are being displayed, the year, month and day of creation of the
software versions are displayed in the same order of version
display.
are being displayed, the year, month and day of creation of the
software versions are displayed in the same order of version
display.
6. Press
[EFFECT]
button, and the key check mode is activated.
7. In the key check mode, the fluorescent indicator tube displays
“KXX V0 C T”. Each time a button is pressed, “K” value
decreases.
However, once a button is pressed, it is no longer taken into
account.
“V” value increases like 1, 2, 3...if rotating
decreases.
However, once a button is pressed, it is no longer taken into
account.
“V” value increases like 1, 2, 3...if rotating
[VOLUME]
knob
in the clockwise, or it decreases like 0, 9, 8...if rotating in the
counterclockwise.
Each time the “CD DOOR LOCK DETECT” or “CD DOOR
OPEN/CLOSE DETECT” switch is turned on, “C” value in-
counterclockwise.
Each time the “CD DOOR LOCK DETECT” or “CD DOOR
OPEN/CLOSE DETECT” switch is turned on, “C” value in-
x
1
1
1
1
1
1
creases.
Each time the “CASSETTE LID OPEN/CLOSE DETECT”
switch is pressed, “T” value increases.
Each time the “CASSETTE LID OPEN/CLOSE DETECT”
switch is pressed, “T” value increases.
8. Also when
[GROOVE]
is pressed after lighting of all LEDs
and fluorecsent indicator tube, value of VACS appears.
9. To exit from this mode, press three buttons in the same man-
ner as step 1, or disconnect the power cord.
[MC TEST MODE]
•
This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
of Amplifier, Tuner, and Tape.
1. Entering the MC Test Mode
Procedure:
1. Press the
1. Press the
[I/ ]
button to turn the power on.
2. Press the three buttons of
[ ]
,
[DISPLAY]
and
[CD SYNC HI-
DUB]
simultaneously.
3. The segments blinks on the fluorescent indicator tube as bel-
low.
2. Releasing the MC Test Mode
Procedure:
1. To release this mode, press the
1. To release this mode, press the
[I/ ]
button.
2. The cold reset is enforced at the same time.
3. Check of Amplifier
Initial settings:
Input , DIGITAL
EQ
EQ
, FLAT
Mode , MUSIC
VACS , OFF
VACS , OFF
Output channel setting:
Each time the
Each time the
[EFFECT]
button is pressed, output channels switch
as following order.
x
x
1
DIGITAL
EFFECT
Blink
1
Order
Channels
Bass Manage
VACS
*
1
1
L t L
Through
ON
R t R
2
L t L
Through
OFF
R t R
3
L t SL
Through
ON
R t SR
4
L t SL
Through
OFF
R t SR
5
L t L, C, SL
on
ON
R t R, SR, SW
6
L t L, C, SL
on
OFF
R t R, SR, SW
7
L t C
Through
ON
R t SW
8
L t C
Through
OFF
R t SW
*
1
) “EFFECT” indication
Click on the first or last page to see other DHC-FLX5D / DHC-FLX7D / HCD-FLX5D / HCD-FLX7D service manuals if exist.